Loading ...
Loading ...
Loading ...
INSTALLATION INSTRUCTIONSINSTALLATION INSTRUCTIONS
Location Requirements
Flooring
For best performance, you must install your washer on a solidly constructed floor. Wood
floors may need to be reinforced to minimize vibration and/or unbalanced load situations.
- Carpeting and soft tile surfaces are contributing factors to vibration which can cause
your washer to move slightly during the spin cycle.
NEVER INSTALL ON A PLATFORM OR WEAKLY SUPPORTED STRUCTURE.
CAUTION
Drain facility
The recommended height of the standpipe is 48in. / 120cm.
The suitable drainage is available in various up to 96in. / 240cm.
The drain hose must be routed through the drain hose clip to the standpipe.
The standpipe must be large enough to accept the outside diameter of the drain hose.
The drain hose is attached to the washer at the factory.
height
Room for washer
Required dimensions for installation
LQ
FP
44.2 in.
112.0cm
38.5 in.
97.5 cm
29 in.
736cm
&ORVHWRU'RRU
48 in²
310 cm²
24 in²
155 cm²
3 in
76 cm
Requiredspacing
Location Requirements
Electric
- 120Volt 60Hz 15 Amps fuse or circ uit breaker.
- Individual branch circuit serving only for your washer is recommended.
- Your washer is equipped with a power cord.
NEVER USE AN EXTENSION CORD.
CAUTION
Grounding
ELECTRICAL GROUNDING IS REQUIRED FOR THIS APPLIANCE.
- This appliance must be grounded. In the event of malfunction or breakdown, grounding
will reduce the risk of electric shock by providing a path of least resistance for electric
current.
- This appliance is equipped with a power cord having a three-prong grounding plug for
use in a properly installed and grounded outlet.
- The plug must be plugged into an appropriate outlet that is properly installed and
grounded in accordance with all local codes and ordinances.
An improperly connected equipment-grounding conductor can increase the risk of
electrical shock. Check with a qualified electrician or serviceman if you are not
sure whether the appliance is properly grounded. Do not modify the plug provided
with the appliance.
- If it does not fit the outlet, have a proper outlet installed by a qualified electrician.
To prevent unnecessary risk of fire, electrical shock or personal injury, all wiring
and grounding must be done in accordance with the National Electrical Code
ANSI/FNPA, No.70 Latest Revision and local codes and ordi
nances. It is the
personal responsibility of the appliance owner to provide adequate electrical
service for this appliance.
WARNING
NEVER CONNECT THE GROUND WIRE TO PLASTIC PLUMBING LINES, GAS
LINES, OR HOT WATER PIPES.
CAUTION
Water
To correctly fill your washer in the proper amount of time, water pressure of 14 to 116psi
(100 to 800kPa) is required.
- Water pressure less than 14psi may cause water valve failure, or may not allow the
water valve to shot off completely, or may extend the fill time beyond what your washer
controls allow, causing your washer to turn off and set off an error alarm. A time limit is
built into the controls to prevent flooding in your home if a hose becomes loose.
The water faucet must be within 4 feet / 122cm of the back of your washer to match the
inlet hoses provided with your washer.
Inlet hoses are available in va
rious lengths up to 8 feet / 240cm for faucets that are
further away from the back of your washer.
To avoid the possibility of water damage:
- Have water faucets easily accessible
- Turn off faucets when the washer is not in use.
- Periodically check that there is no leakage from the water inlet hose fittings.
44.2 in.
112.0cm
59 in.
150.0cm
3 in
76 cm
11
12
IMPORTANT: Do not install your washer in areas where water may freeze, since your washer will
always retain some water in its water valve, pump, and hose areas. Frozen water can damage the
belts, the pump, hoses, and other components.
IMPORTANT: Check all connections at the water valve and faucet for leaks.
Loading ...
Loading ...
Loading ...