Leviton IPV15-1LZ INSTALLATION INSTRUCTIONS

Loading ...

•Positionallwirestoprovideroominoutletwallbox

fordevice.

•Ensurethattheword"TOP"isfacingupondevice

strap.

•Partially screw in mounting screws in wall box

mounting holes.

•Removethefacecoverofthesensortoexpose

the adjustment dials (refer to Changing the

Color of your Device on page 1).

•Settimeselectionofthesensorto30seconds

foraquicktimeoutduringtesting(Refer to

ADJUSTMENT SETTINGS section).

•Setthelightleveldialfullclockwise(Refer to ADJUSTMENT SETTINGS

section).

•Placethefacecoverbackonthesensor.

•Restorepoweratcircuitbreakerorfuse.

•ForIPS15lightswillautomaticallyturnonafterpowerisapplied.

•ForIPV15,pressandreleasepushpadtoturnthelightsON.

NOTE: See Locator Light Status chart to conﬁrm the operational state of

thedevice.IflightsstilldonotturnON,refertotheTROUBLESHOOTING

section.

•Leavetheroomoreldofviewtoallowthesensortotimeoutandshutoff

the lights due to absence of motion.

•Within30secondsofthelightstimingoutstepbackintotheroomorthe

eldofviewofthesensorandthelightsshouldturnbackonautomatically.

•Ifthelightsdonotturnoff30secondsafterleavingtheroomdecreasethe

sensitivityofthesensor(refer to the ADJUSTMENT SETTING section).

•Ifthelightstonotturnbackonautomaticallywhenyoustepbackintothe

roomincreasethesensitivityofthesensor(refer to the ADJUSTMENT

SETTING section).

•Settimeselectionandlightlevel(Refer to ADJUSTMENT SETTINGS

section).

•Whenthedesiredlightlevel(IPS15 only),timeselectionandsensitivity

settingsareselectedplacethefacecoverbackonthesensorand

continue to Step 6.

Restore Power: Restore power at circuit breaker or

fuse.

Installation is complete.

Step 7

Device Mounting:

TURN OFF POWER AT

CIRCUIT BREAKER OR FUSE.

Step 6

Installation may now be

completed by tightening

mounting screws into wall

box. Attach wallplate.

Testing your Device prior to mounting in wall box:

Step 5

NOTE: Dress wires with a bend as shown in diagram in order

torelievestresswhenmountingdevice.

ADJUSTMENT SETTINGS

NOTE: Toavoid PERMANENT DAMAGE to the unit, be careful NOT TO

OVERTURN the adjustment dials when setting the Sensor.

1. Withpowerrestoredandwallplateremoved,removefaceofdevicetoexpose

adjustment dials (refer to Changing the Color of your Device on page 1).

Useasmallscrewdrivertoadjustthelightlevel,timeselectionandsensitivity

onthedeviceasfollows (Refer to Diagram):

Light Level Adjustment (IPS15 only):

•Adjustthelightleveldialclockwise.LightswillturnONinlighterconditions.

•Adjustthelightleveldialcounterclockwise.LightswillturnONinlesslighting

conditions.

Time Selection:

•Adjustthetimeselectordialtothedesiredlengthoftimethelightsareto

remainON.LightswillremainONfrom30secondsto30minutesafterthe

roomisvacated.

•AdjustthetimeselectordialclockwisetoincreasethedurationoftheON

timeupto30minutes.

•Adjustthetimeselectordialcounterclockwisetodecreasethedurationofthe

ONtimedownto30sec.

Sensitivity:

•Increaseordecreasethesensitivityofthesensorasfollows.

•Todecreasesensitivityanddetectionrange,rotatethedialcounter-clockwise.

Toincreasethesensitivityanddetectionrange,rotatethedialclockwise.With

thearrowpointingat3thesensitivityisfull.Withthearrowpointingat0,the

sensitivityisreducedbyhalf.Asthedialrotatesfrom2to0,thechangein

sensitivityismadeinnesteps.

2. Attachthefacecoverandtestthatthelightlevel,timeselectionand

sensitivityaresetasdesired.Ifnot,repeatadjustmentsuntilsatised.

For additional information, contact Leviton’s Techline at

1-800-824-3005 or visit Leviton’s website at www.leviton.com

ThisproductiscoveredbyU.S.Pat.No.7,924,155

and corresponding foreign patents.

©2012LevitonManufacturingCo.,Inc.

AllRightsIncludingTradeDressRightsReserved

TROUBLESHOOTING

Lights do not switch ON - IPS15:

• Motionisbeyondsensingrange,moveclosertoswitch.

• Adjustthelightleveladjustmenttowardlighterordarker,dependingon

room conditions.

Lights always stay ON:

• ChecktimedelaysettingsandcomparetohowlongthelightsstayON.

• Besurethatnomotionoccursincoverageareafortimeselected.

• Checkthatswitchisnotinstallednearaheatsource(e.g.,stove,lights,

heatvents)ordetectingmotionfromanadjacentarea(e.g.,hallway

trafc).Ifso,switchmayhavetoberelocated.

• 

TryloweringtheSensitivityAdjustmentControl.Rotatetheknob

counterclockwiseabout30°.Iftheproblempersists,tryreducingagain.

NOTE: DO NOT reduce so much that the sensor cannot see normal

occupancy.

Lights do not turn ON with the pushpad - IPV15:

• Checkthatswitchisinstalledcorrectly.

• CheckthatpowerisON.

• Checkthatlightbulbisfunctioning.

NOTE: If problems continue, consult an electrician.

FCC COMPLIANCE STATEMENT

ThisdevicecomplieswithPart15oftheFCCRules.Operationissubject

tofollowingtwoconditions:(1)thisdevicemaynotcauseharmful

interference,and(2)thisdevicemustacceptanyinterferencereceived,

includinginterferencethatmaycauseundesiredoperationofthedevice.

Thisequipmenthasbeentestedandfoundtocomplywiththelimitsfor

aClassBDigitalDevice,pursuanttoPart15oftheFCCRules.These

limitsaredesignedtoprovidereasonableprotectionagainstharmful

interferenceinaresidentialinstallation.Thisequipmentgenerates,uses,

andcanradiateradiofrequencyenergyand,ifnotinstalledandusedin

accordance with the instructions, may cause harmful interference to radio

communications.However,thereisnoguaranteethatinterferencewill

notoccurinaparticularinstallation.Ifthisequipmentdoescauseharmful

interferencetoradioortelevisionreception,whichcanbedetermined

byturningtheequipmentOFFandON,theuserisencouragedtotryto

correct the interference by one or more of the following measures:

• ReorientorrelocatethereceivingAntenna.

• Increasetheseparationbetweentheequipmentandthereceiver.

• Connecttheequipmentintoanoutletonacircuitdifferentfromthatto

whichthereceiverisconnected.

• Consultthedealeroranexperiencedradio/tvtechnicianforhelp.

FCC CAUTION

AnychangesormodicationsnotexpresslyapprovedbyLeviton

ManufacturingCo.,Inc.,couldvoidtheuser'sauthoritytooperatethe

equipment.

LOCATOR LIGHT STATUS

LOAD

IPS15 IPV15

OFF

Blinking Lit

Blinking Blinking

Lens

Push

Pad

Locator

Light

Side (Vertical) Field-of-View

SENSING AREA COVERAGE

Field-of-View (Horizontal)

30ft

9.1m

30ft

9.1m

6ft

1.7m

1.8m

6ft

30ft

9.1m

8.4m

27ft

2.1m

7ft

1.2m

4ft

2.6m

8ft

Light Level

Adjustment

Sensitivity

Adjustment

Time

Selection

1 2

0 3

1 2

0 3

1 2

0 3

Settings

Time

30sec

5 min

15 min

30min

PK-93977-10-00-2A©2012LevitonMfg.Co.,Inc.

NOTE:TheOccupancysensormust be installed in a wall box that

hasaLoadconnection.TheSensorremotemust be installed in a

wallboxwithaLineHotconnectionandaNeutralconnection.A

Neutralwiretotheremoteneedstobeaddedasshown.Ifyouare

unsure about any part of these instructions, consult an electrician.

NOTE: Maximum wire length from sensor to all installed remotes

cannotexceed300ft(90m).

WIRING REMOTE

(wall box with Line Hot connection):

Connect wires per WIRING DIAGRAM as follows:

•GreenorbarecopperwireinwallboxtoGreenterminalscrew.

•LineHot(common)wallboxwireidentied(tagged)when

removingoldswitchandFirstTravelertosensorterminalscrew

marked "BK".

•SecondTravelerwallboxwirefromsensortoremoteterminalscrew

marked"3-Way"(note wire color).Thistravelerfromtheremote

mustgototheterminalscrewonthesensormarked"3-Way".

•Neutralwallboxwiretoremoteterminalscrewmarked"WH".

WIRING SENSOR (wall box with Load connection):

Connect wires per WIRING DIAGRAM as follows:

•GreenorbarecopperwireinwallboxtoGreenterminalscrew.

•Loadwallboxwireidentied(tagged)whenremovingoldswitchto

terminal screw marked "RD".

•FirstTravelerLineHottoterminalscrewmarked"BK".

•RemoveRedinsulatinglabelfromterminalscrewmarked"3-Way".

•SecondTravelerwallboxwire(note color as above) to terminal

screwmarked"3-Way".Thistravelerfromthesensormustgotothe

terminalscrewontheremotemarked"3-Way".

•Neutralwallboxwiretoremoteterminalscrewmarked"WH".

•ProceedtoStep5.

3-Way Wiring with Sensor Remote or Vizia

Matching Remote (w/LED) Application:

NOTE: IPV0R sensor remote is depicted.

Additional

Neutral Wire

Terminal

Screw marked

Black (BK)

Brass Terminal

Screw marked

3-Way

Terminal

Screw marked

Red (RD)

Terminal

Screw marked

White (WH)

SensorIPV0R/VP0SR-1L Remote

Ground

Terminal Screw

(Green)

Hot (Bla c k )

Neutral (White)

Sensor IPV0R/VP0SR-1L Remote

3-Way

RD 3-Way

BK BK

Bla c k

White

Line

120 V A C , 60H z

Load

Green

Ground

Green

Ground

OPERATION

IPS15

Auto ON: LightswillautomaticallyturnONwhenroomisoccupiedormotion

isdetected.TheIPS15willswitchlightsOFFwhennomotionisdetectedin

un-occupied room after set period of time.

Time delay adjustment: Refer to section on Adjustment Settings.

Manual ON:TheIPS15willmanuallyturn-onlightsortheloadbydepressing

thepushpadonthedevice.TheIPS15canbesettoonlyturnONbythe

pushpad(noautomaticonoperation)byadjustingtheambientlightcontrolto

the "0" position.

IPV15

Manual ON:

TheIPV15requirestheusertomanuallyturnONlightsortheload

by depressing the

push pad

onthedevice.Thelightsorloadwillautomatically

turn-off when the room is left unoccupied for a set period of time.

Time delay adjustment: Refer to section on Adjustment Settings.

NOTE:

Ina3-wayapplication,usingvizia

matching or coordinating remotes,

theremotewillonlyhavetheabilitytomanuallyswitchtheloadON,thesensor

willthentimeoutandswitchtheloadOFFoncemotionisnolongerdetected.

For automatic control at both locations, use IPV0R as the remote.

Locator Light LED:

IPS15:LEDblinkswhenmotionisdetectedandiftheloadisONorOFF.

IPV15: LEDblinkswhenmotionisdetectedandwhenloadisON.LEDwill

remainilluminatedwhenloadisOFF.

Leviton IPV15-1LZ Decora Vacancy Motion Sensor In-Wall Switch, Manual-On, 15A, Single Pole or 3-Way, White/Ivory/Light Almond

INSTALLATION INSTRUCTIONS - Page 2