Loading ...
Loading ...
Loading ...
To turn on the appliance, press the “ ” button on the control
panel. To turn off the appliance press the “ ” again. A countdown
from 10 to 1 will be displayed and then the heater will revert to
standby mode, see Fig. 9. The rst time the appliance is turned
on the appliance will set to 22
o
C as the default temperature, the
default mode setting is “Eco”. Subsequently, when the appliance
is turned on it will power on at the last set temperature and mode.
The display will show the current set temperature, see Fig. 5. The
set temperature range starts at 5
o
C and ends at 30
o
C. The set
temperatures are colour coded to easily identify optimal settings.
The colour coding is noted in Fig. 5. To change the set temperature
press “ ” to raise the desired temperature and press “ ” to lower
it. If either button is pressed and held for 1 second or more the
temperature will continually rise or fall until button is released.
When the air temperature rises above the set temperature, the
heat will switch off but the fan will continue to run for 25 seconds.
When the air temperature drops below the set temperature, the
unit will come back on. If the heater is not operating this may be
because the set temperature is lower than the room temperature. If
no buttons have been pressed for 10 seconds, the display screen
will go into sleep mode. The screen backlight will fade to 20% of
its intensity.
Note: When in heating mode if the “ ” button is pressed the fan
will continue to run for 15 seconds while counting down 10 to 1
on screen.
Audio - see Fig. 6
When a button is pressed the heater emits and audible beep. If
the “ ” + “ ” buttons are pressed and held for 2 seconds this
will turn off audio for button presses. If both buttons are pressed
and held again the audio will be turned on again. The screen will
show either the audio on or audio off symbols as shown in Fig.
6. After 2 seconds display will return to the temperature screen.
Fan Only Mode - Fig. 7
If the “ ” + “ ” buttons are pressed and held for 2 seconds this will
switch the appliance into fan only mode. In this mode the heating
elements are powered down and the appliance will blow cool air.
The fan symbol “ ” will appear on the display when the appliance
is in fan only mode. If the “ ” + “ ” buttons are pressed and held
again for 2 seconds this will switch the appliance out of fan only
mode and the display screen will return to the temperature screen.
Oscillation - See Fig. 8 & Fig. 12 (M2GTS Only)
The heater can be switched into oscillation mode by pressing the “
” button on the control panel. An oscillation graphic will appear at
the top of the temperature screen, see Fig. 8. The heater oscillates
back and forth on its base through 90 degrees as shown in Fig. 12.
Power Settings - see Fig. 10
The heater has 3 power settings. To cycle through these settings,
press and hold the “ ” button for 2 seconds. This will bring up the
power setting screen. Press the “ ” button again to cycle through
the 3 settings, “Low”, “High” and “Eco”, as shown in Fig. 10. The
settings will ash when displayed on the screen. Once a setting
is left highlighted for 6 seconds it will then become selected and
return to the temperature screen. Press the “ ” button at any
time to cancel the operation. When in “Eco” setting the heater will
automatically switch between “High” (2000W) and “Low” (1000W)
setting as required to maintain the set temperature.
‘Intelligent’ Eco Mode
This is the appliance default setting, the appliance will automatically
start up in this setting once power is applied and the standby
key is pressed. The LCD display will indicate the desired room
temperature and the appliance will automatically regulate the room
temperature accordingly. In this mode the appliance operates at
full power, however the output of the appliance is automatically
reduced and regulated as the room temperature approaches the
desired level. This mode optimises energy use by calculating the
most efcient and effective way to achieve the desired temperature
setting. The desired room temperature can be adjusted at any time
during operation by pressing the appropriate key.
Runback Timer Mode - See Fig. 11
The heater is tted with a run-back timer feature which can be set
in any of the operating modes. Press the “ ” button to switch to the
runback timer screen. The runback timer range is 1 to 12 hours.
The displayed runback time will be ashing on screen, starting
at “01 Hrs”. Press the “ ” button again to increase the runback
time by 1 hour. Pressing “ ” will cancel the runback operation.
Once the desired runback time is left to ash for 6 seconds the
timer will be set. The display will switch back to the temperature
screen with the runback countdown displayed below as shown in
Fig. 11. To cancel the current runback timer, press the “ ” button.
The runback countdown will ash to “OFF” then disappear. Once
the run time has been set the heater will run and the runback
countdown will remain on the display until the set time runs out.
At this point the heater will switch to standby mode. To turn the
heater back on, press the “ ” button.
Note: If runback countdown is active in Fan mode the text below the
fan symbol will alternate between “Fan” and runback countdown.
Tilt Switch
The heater is tted with a tilt switch which will prevent the heater
from working if the heater is accidentally tipped over in any
direction.
Overheat Protection
The heater is tted with a temperature limiter. If the air inlet or outlet
grilles are restricted in anyway the temperature limiter switches the
heater off automatically. To bring the heater back into operation,
remove the cause of overheating then unplug the unit from the
electricity supply for a few minutes. When the heater has cooled
sufciently reconnect and switch on the heater.
Electronic Thermostat
In addition, if the electronic thermostat reads an abnormal ambient
room temperature it will cut the power to the heater and display
“ERROR” on screen. When the temperature has cooled to an
acceptable ambient room temperature it will restore power to the
heater and “ERROR” will disappear from the screen. The heater
will return to previous operation mode. The heater will then operate
as normal, if the heater does not switch on this may be because
the room temperature is still warmer than the set temperature.
Cleaning
Switch off the appliance rst and disconnect the plug from the
socket. Clean the housing with a moist cloth, vacuum cleaner or
brush. Do not use any abrasive or caustic cleaning agents. Do
not use any ammable cleaning agents e.g. petrol or spirit for
cleaning the appliance. Never immerse the appliance in water.
Air inlet and outlet area should be cleaned with a vacuum cleaner
regularly· If the appliance is not used for extended periods, it must
be protected against excessive dust and dirt.
Recycling
For electrical products sold within the European
Community. At the end of the electrical products useful
life it should not be disposed of with household waste.
Please recycle where facilities exist. Check with your
Local Authority or retailer for recycling advice in your
country.
After sales service
Your product is guaranteed for 3 years from the date of purchase.
After sales information or assistance with this product can be found
on our website: www.dimplex.co.uk/support
Your rights under this guarantee are additional to your statutory
rights, which in turn are not affected by this guarantee.
Please do not return a faulty product to us as this may result in loss
or damage and delay in providing you with a satisfactory service.
If after following these steps your product still does not operate
you should return it to your point of purchase.
Please retain your receipt as proof of purchase.