Loading ...
Loading ...
Dimplex M2GT & M2GTS Ceramic Fan Heaters
THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
IMPORTANT SAFETY ADVICE
DO NOT use the heater in the immediate
surroundings of a bath, a shower or a swimming
pool.
DO NOT place the heater directly below a xed
socket outlet.
The socket-outlet must be accessible at all times
to enable the mains plug to be disconnected as
quickly as possible.
DO NOT COVER the heater or obstruct the air
inlet and outlet openings in any way.
DO NOT operate the heater with the mains lead
overhanging the front outlet grille.
WARNING: In order to avoid overheating do not
cover the heater.
IMPORTANT: If the mains lead of this appliance is
damaged, it must be replaced by the manufacturer
or its service agent or a similarly qualied person
in order to avoid a hazard.
WARNING: In order to avoid a hazard due to
inadvertent resetting of the thermal cut-out,
this appliance must not be supplied through an
external switching device, such as a timer, or
connected to a circuit that is regularly switched
on and off by the utility.
This appliance can be used by children aged from
8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of
experience or knowledge if they have been given
supervision or instruction concerning the use of
the appliance in a safe way and understand the
hazards involved. Children shall not play with the
appliance. Cleaning and user maintenance shall
not be made by children without supervision.
Children of less than 3 years should be kept away
unless continuously supervised.
Children aged from 3 years and less than 8 years
shall only switch on/off the appliance provided
that it has been placed or installed in its intended
normal operating position and they have been
given supervision or instruction concerning the
use of the appliance in a safe way and understand
the hazards involved. Children aged from 3
years and less than 8 years shall not plug in,
regulate and clean the appliance or perform user
maintenance.
CAUTION: Some parts of this product can
become very hot and cause burns. Particular
attention has to be given where children and
vulnerable people are present.
IMPORTANT: The heater must be on a at stable
surface when in use.
IMPORTANT: Avoid use of an extension cord
because the extension cord may overheat and
cause risk of re.
Keep combustible materials such as drapes and
other furnishings clear from the front, sides and
rear of the heater. Do not use heater to dry your
laundry.
IMPORTANT: Minimum distance to heater of
150mm from the back and sides and 300mm
from the top to any surface must be maintained
at all times.
Electrical connection
This heater must be used on an A.C. ~ supply only and the voltage
marked on the heater must correspond to the supply voltage. This
heater is tted with a plug incorporating a 13-amp fuse. When
replacing the fuse, a 13-amp fuse approved by ASTA to BS 1362
must be used.
If the plug is not suitable for the socket outlets in your home, the
plug must be cut off and an appropriate one tted. A plug cut off
from a mains lead will give a shock hazard if inserted into a 13-
amp socket elsewhere in the house. To avoid this, it should be
disposed of immediately.
NOTE: The fuse cover of a non-rewirable plug must be retted
when changing the fuse. Should the cover become lost, the plug
must not be used until the correct replacement fuse cover is
obtained from your supplier or by contacting our customer helpline.
IMPORTANT: The wires in this mains lead are coloured in
accordance with the following code:
BLUE: NEUTRAL
BROWN: LIVE
GREEN & YELLOW: EARTH
As the colours of the wires in the mains lead may not correspond
with the coloured markings in your plug, proceed as follows:
Connect the BROWN wire to the terminal marked ‘L’ or coloured
RED. Connect the BLUE wire to the terminal marked ‘N’ or
coloured BLACK. Note: ‘L’ or ‘N’ must not be connected to the
EARTH terminal marked ‘E’ or ‘ ’ or coloured GREEN or GREEN
AND YELLOW.
If in doubt, consult your electrician.
Operation
Main Elements - See Fig. 2
1. Control Panel
2. Display Screen
3. Air Outlet
4. Oscillation Base (M2GTS Only)
The heat output is controlled electronically according to the room
temperature. When the unit is plugged in the display screen will
light up white with STANDBY displayed at the bottom of the screen,
see Fig. 9, and the appliance will beep once. After 10 seconds the
intensity of the display will fade to 20%. The display will remain lit
until the appliance is disconnected from the mains or a button is
pressed. The control panel elements are shown in Table 1, Fig. 3
(M2GT) and Fig.4 (M2GTS).
Table 1
Standby
Runback Time
Plus Button
Minus Button
Oscillation (M2GTS Only)
Loading ...