Loading ...
Loading ...
Loading ...
20 | English
F 016 L81 437 | (23.11.15) Bosch Power Tools
Longer material standing out from the machine could
lash out when being pulled in by the knives! Please
keep at safe distance!
– Only insert as much material so that the chute assembly 8
will not be blocked up.
– Shred withered, moist material and garden waste which
has been stored for some days alternately with branches.
This prevents the cutting roller 16 from clogging.
– Do not fill soft waste such as kitchen rubbish into the
shredder but compost directly.
– Take care that the shredded material can fall freely from
the discharge chute – danger of backing up!
– The ventilation slots 3 must not be covered by the shred-
ded material.
– Avoid blocking the discharge chute with shredded material
as this could result in kickback of material through the
chute assembly 8 opening.
Advice on Shredding
Branches become harder to shred depending on the type, age
and dryness of the wood.
For best results, shred fresh branches soon after they have
been cut.
Soft garden waste should be shredded in smaller loads, par-
ticularly when wet. Any blockages can be avoided by intermit-
tently shredding branches.
Pressure Plate Adjustment (see figureH)
The pressure plate 15 is factory adjusted and may not require
adjustment before the first use.
Adjustment of the pressure plate 15 is necessary as a result of
wear (shredded material, e. g. branches, hangs together as a
chain and is not properly cut through).
With the motor running in the forward direction (green button
4), turn the adjustment knob 10 a small amount at a time in a
clock wise direction until a light grinding sound can be heard
(the cutting roller 16 cuts the pressure plate 15 to the proper
clearance, and some small aluminium shavings fall out of the
ejection chute).
To check, look for shavings in the collection box 11.
Readjust only to the required extent, otherwise the pressure
plate 15 could wear unnecessarily.
Troubleshooting
The following chart lists problem symptoms, possible causes and corrective action, if your garden product does not operate
properly. If these do not identify and correct the problem, contact your service agent.
Warning! Switch off, remove plug from mains before adjusting, cleaning or if cable is cut, damaged or entangled.
Problem Possible Cause Corrective Action
Machine fails to operate Collection box not fitted correctly Fit collection box correctly
Chute assembly not fitted correctly Fit chute assembly correctly
Mains socket faulty Use another socket
Extension cable damaged Inspect cable, replace if damaged
The machine is overheated Wait until the machine cools down
Fuse faulty/blown Replace fuse
Machine beeps (also two lights
on AXT 23 TC/25TC/2550TC)
and does not start
Collection box/chute is not correctly
assembled
Ensure the collection box is in position
Ensure the chute assembly is in position and clamped
by turning the clamping knob (red) fully clockwise
Machine periodically beeps
three times and does not start.
(also two lights are flashing rap-
idly the same way on
AXT 23 TC/25 TC/2550 TC)
Undervoltage protection Press the STOP button. Wait until the machine cools
down. The machine will beep for 2 seconds and switch
to standby.
One flashing light on
AXT 23 TC/25 TC/2550 TC
None, this is ok, machine is “pluged
in” and ready to use
Machine periodically beeps
three times and does not start.
(also two lights are flashing rap-
idly the same way on
AXT 23 TC/25 TC/2550 TC)
Undervoltage protection Restart machine.
Check extension cable is as required in instructions
(lower quality extension cables can cause error)
When powered by aggregator, check its performance.
Machine beeps continuously for
10 seconds and does not start,
error cannot be cleared pressing
STOP button (also two lights are
blinking the same way on
AXT 23 TC/25 TC/2550 TC)
The electronic control unit is faulty Contact your Bosch Service Centre
OBJ_BUCH-895-007.book Page 20 Monday, November 23, 2015 8:59 AM
Loading ...
Loading ...
Loading ...