Loading ...
Loading ...
Loading ...
4.6. Adjusting the coarseness of grinding
Attention: Only adjust the grinding coarseness whilst the grinder is running.
You can adjust the grinder according to the particular blend of bean. We suggest the grinder is kept
on a medium setting.
To change the coarseness of the grinding, please follow these steps:
➔ Open the service door on the right of the casing (g. 1/L).
The grinding coarseness control is at the top right (g. 9).
➔ Place a cup under the spout
➔ Turn the rotary control to “ESPRESSO” and press it.
➔ While the grinder is grinding, change the coarseness of grinding by moving the control (g. 9).
The smaller the dot, the ner the coffee powder will be. Please note:
• A light roast level needs ner grinding adjustment (control further to the left).
• A dark roast level requires coarser grinding adjustment (control further to the right).
Check out for yourself the best setting according to your personal taste.
➔ Close the service door and in doing so carefully place the pivots at the back of the service door
into the notches. Make sure that the door completely snaps back into place.
4.7. Making ground coffee (e.g. for decaffeinated coffee)
➔ Open the lid on the right of the appliance (g. 1/G)
➔ Open the lid of the coffee powder chute (g. 1/M).
The display shows “INSERT GROUND COFFEE”.
➔ Pour in one level measuring spoon of ground coffee and close the lid. The display shows
“GROUND COFEE READY”.
➔ Place a cup under the spout (g. 5).
➔ Turn the rotary control to the drink of your choice.
➔ Press the button > until the ml-display is blinking.
➔ While “ml” blinks, turn the rotary control to the required quantity.
➔ The new setting is stored when you press the exit button or if you do not carry out any further
changes.
➔ Press the rotary control to start the preparation.
Note: Should you have started the process accidentally or too early, you can also change the quantity
during the preparation.
➔ When the “ml” display is blinking, turn the rotary control to the required position.
➔ If you want to stop the process, press exit button (g. 1/D).
Note: If you have opened the lid of the coffee powder chute accidentally or did not press the rotary control
after having poured in the ground coffee, the appliance will automatically start rinsing for a minute once
the lid is closed (g. 1/E). The appliance will then be operational again.
Attention: The coffee powder chute is not a storage container. Therefore never pour in more than one
portion of coffee and only use fresh or vacuum-packed coffee ground from coffee beans. Do not use
water-soluble instant coffee!
5. Cleaning and maintenance
Your Nivona appliance will show some maintenance requirements on the display (e.g. PLEASE
CLEAN FROTHER”).
➔ If cleaning or maintenance is required and the large icons are set in the main menu turn the
rotary to the “hand symbol”; if the small icons are set turn the rotary until the required mainte-
nance task shows up in the main menu. Then press the rotary.
Your appliance will start the respective cleaning or maintenance programme and will ask you in the
display for further steps.
➔ Follow the instructions on the display. If in doubt go to 5.1. to 5.9. for more details.
5.1. Rinsing the milk frother
Note: Do not disrupt the running program!
We advise you to rinse the frother after each drink for which milk was used, it should denitely be
rinsed when the display asks you to do so.
➔ Turn the rotary control to “MAINTENANCE” and press it.
➔ Turn the rotary control to “RINSE FROTHER” and press it.
The display shows “CONNECT HOSE TO SPOUT AND DRIP TRAY”.
➔ Connect the hose to the spout (g. 7).
➔ Connect the other end to the back of the drip tray (g. 10).
➔ Place a sufciently large bowl (about 0.5 l) under the spout.
➔ Press rotary control.
The display shows “RINSING FROTHER, DO NOT REMOVE HOSE”. The appliance then starts the
cleaning process. Once the process is nished the appliance reheats and is ready for use. The display
shows the main menu.
5.2. System rinsing
From time to time the system should be rinsed. Proceed as follows:
➔ Turn the rotary control to “MAINTENANCE” and press it.
➔ Turn the rotary control to “SYTEM RINSING” and press it.
The display shows “RINSING SYSTEM”.
Once the process is nished, the appliance reheats and is ready for use. The display shows the main
menu.
5.3. Cleaning frother
Attention: Do not disrupt the running program!
Note: The display shows “PLEASE CLEAN FROTHER” when it is required.
Proceed as follows:
➔ Turn the rotary control to “MAINTENANCE” and press it.
➔ Turn the rotary control to “CLEAN FROTHER”.
The display shows “EMPTY TRAYS” and “FILL WATER” alternatingly.
➔ Remove drip tray with used coffee container (g. 1/N and 1/O) and empty both.
➔ If necessary rell the water tank with fresh water. Reinsert the water tank rst, followed by drip
tray and used coffee container.
The display shows “CONNECT HOSE TO SPOUT AND IN CLEANER”.
➔ Connect the hose to the spout (g. 7).
➔ Put some detergent (available as an optional accessory, see 8.) and water in a container, both
should amount to 0,3l. For the correct mix refer to instructions by the detergent’s manufacturer.
➔ Dip the other end of the hose into the cleaning solution
➔ Place a sufciently large bowl (minimum contents 0.5 l) under the spout.
➔ Press the rotary control.
The display shows “START CLEANING”.
➔ Press the rotary control.
The cleaning process is started. The display shows “CLEANING FROTHER. DO NOT REMOVE
82 83
4. Preparing coffee varieties / 5. Cleaning and maintenance 5. Cleaning and maintenance
Loading ...
Loading ...
Loading ...