Loading ...
When the battery is low, the light will start to shine
weakly. We suggest you charge the batteries after
every use to keep them ready to use. Place the
battery properly into the charger.
1.Remove the head of KL52 PLUS
2.Rotate the tail cap toward to LED side
3.Unscrew and replace with different clolor LED
module
4.Screw up the head of KL52 PLUS as far as it can
go.
*The specifications in the chart above claim to ANSI/NEMA FL1-2009
Standards. Tests are performed with 1X 18650 battery (3.7V. 3000mAh).
All specification are subject to change without prior notice
1.Please keep the battery positive pole (+)
towards the flashlight head (The LED direction).
2.Odepro recommends using excellent quality
battery. If the light will not be used for an
extended period, remove the battery to avoid
damage from electrolyte leakage or battery
explosion.
3.Long-term use can result in O-ring abrasion.
Check the condition of O-rings every time you
open the body of the light. Replace the ring with
an approved spare to keep the light properly
sealed against water.
4.Please clean the contacts of your light periodi-
cally to keep the light performance good,
especially when the light flickers or does not light
up. There are probably several reasons for a
flickering or not working light as following:
Reason A:
The battery need to be replaced.
Solution: Replace battery (please confirm the
correct installation of anode and cathode).
Reason B:
The threads, PCB board contact or
other contacts are dirty.
Solution: Clean the contact points with a cotton
swab soaked in rubbing alcohol. If the above
methods don’t work, please refer to the warranty
policy and contact us for customer service.
Danger:
Never point the flashlight into your eyes or the
eyes of other people otherwise it will cause your
eyes blind or get hurt.
(1)30 days free replacement: Return to Odepro
for free replacement.
(2) 24 months free repair: Reture to Odepro for
repair.
(3) Limited lifetime warranty: If problems develop
after 24 months of the purchase, we will charge
for parts. The total repair fee is assessed
according to the cost of the replaced materials.
This warranty does not cover normal wear and
modifications, misuse, disintegrations,
negligence, accidents, improper maintenance,
or repair by anyone other than Odepro itself.
CUSTOMER SERVICE: service@odepro.com
www.odepro.com
Odepro Technology Co., Ltd.
Add：7F,Building 6,Yusheng Industrial
Park,Gushu,Xixiang,
Baoan,Shenzhen,China 518102
Tel：+86-755-36538983
Fax：+86-755-29454989
HOW TO CHARGE BATTERY
FLASHLIGHT MAINTENANCE
SPECIFICATIONS
MODULE REPLACEMENT
WARRANTY
Red LED : charging in progress.
Green LED : charging fully completed.
Please ensure the positive end (+) pointing to the
head of light and insert the battery properly. If the
battery is not installed correctly, the light can not
turn on properly.
+
-
Replace the LED module
Twist to remove the LED module
BODY
HEAD
LED colors
HIGH
Run time Beam Distance
White 1.63HOURS 400 YARDS
Red 3.3HOURS 375 YARDS
Green 4.1HOURS 452 YARDS
IR850
Infrared is not visible to the human eye.
Use of IR viewing device is required
(WHITE)
lumens
IMPACT 1M/(3.28ft)
LENGTH (flood / spot ) 148mm(5.82in)/171mm(6.73in)
BEZEL DIAM 54mm / 2.12in
WEIGHT (w/o battery) 240g / 8.46oz
MED
(WHITE)
LOW
(WHITE)
SOS
(WHITE)
STROBE
(WHITE)
800
lumens
240
lumens
36
lumens
800
lumens
800
*