Documents: Go to download!
User Manual
- User Manual - (English)
- Product Introduction
- OPERATION METHOD
- Clean and Maintenance
- Common Failures and Diagnosis
- Troubleshooting
Table of contents
Owner's Guide Air Conditioners
Product Introduction
MAIN PARTS AND COMPONENTS
- Handle
- Control panel
- Louver
- Caster
- Air outlet
- Air inlet
- Drainage nozzle
- Remote controller
- Exhaust duct assembly
- Window sealing plate assembly
Control Panel and Remote Controller
- Power key
Press the key to turn ON/OFF the A/C. - Mode key
Press the key to choose cool, fan and dry. - Temperature/ time adjusting key
Press the key at cooling mode to increase/ reduce the setting temperature; press it at timing mode to adjust time; press Up and Down keys simultaneously to switch Fahrenheit and Centigrade degree temperature. - Speed key
Press the key to choose high/ low spee d. - Timer key
Press the key at standby mode to set ON time. Press this key at ON mode to set OFF time. - Temperature/ Time Display Window
See other models: PUCRC25.5 PUCRC96B SLTLSP01 PSLMRB2 PSLMRP15
Displays the adjusted temperature and time - Remote controller receiving window
It is used to receive signal of the remote controller. - °C/°F switching key
Press the key to switch °C and °F - Sleep key
In the cooling mode, the sleep mode can be selected by this key
OPERATION METHOD
Cooling Mode
- When the A/C enters cooling mode automatically or cooling mode is selected after power ON, the cooling indicator lamp lights up.
- Press Up/Down key to adjust setting temperature (16°C~30°C)(60°F~86°F).
- Press Speed key to choose High/Mid/Low speed.
Fan Mode
- When pressing mode key or choosing Fan mode by pressing the remote controller, the wind indicator lamp lights up.
- Press Speed key to choose High/Mid/Low speed.
- Temperature can’t be set.
Dehumidification Mode
- When pressing mode key or choosing dehumidification mode by pressing the remote controller, the dehumidification indicator lamp lights up.
- Remove the dehumidification water wedge, insert water manifold, place the other end of the water manifold into the water vessel or drainage passage, as shown in the right figure.
- After entering the dehumidification mode, if room tempearture≥17°C (62°F), the compressor is ON. Then control as follows: when room temperature ≤15°C (59°F), the compressor is OFF; when temperature increases to room temperature≥17°C (62°F), the compressor will start again (in order to protect the compressor, it will be restarted 3min. later).
- In dehumidification mode, the fan is defaulted to run at low speed, and wind speed can’t be adjusted.
- Temperature can’t be set.
Note : When use dehumidify function, should remove exit pipe components, otherwise, it will cause worse dehumidify performance, and appear “FL” water full alarm
Sleep mode (optional function)
- Under cool mode, pressing sleep mode key on the remote controller or pressing time key and down key together on the machine, it will start sleep mode with low wind speed and can’t be adjusted. Pressing the sleep mode key again or pressing time key and down k ey together on the machine to quit the sleep mode.
- If you press the wind speed key under the sleep mode, the screen will display ”SL”
Timer Mode
- In standby state, press the Timer key to set ON time. Press Up and Down keys to set ON time (0~24H), and the timer indicator lamp lights up.
- In ON state, pressure the timer key to set OFF time. Press Up and Down keys to set OFF time (0~24H), and the timer indicator lamp lights up.
Clean and Maintenance
DRAINAGE METHOD
This product is equipped with automatic water vaporization system. The condenser is cooled with the circulating of condensing water, so as to improve cooling efficiency and save energy.
- If the internal vessel is full of water, the display screen will display “FL”, and the compressor stops working automatically. After power off, unscrew the water cover, pull out the water plug to drain off water, and it will become normal after being restarted.
MAINTENANCE
Notice: In order to avoid electric shock, please turn off the A/C and unplug before maintenance or repair.
CLEANING
- Unplug before cleaning.
- Wipe with soft semi-dry cloth. Don’t use chemical reagent, such as benzene, alcohol and gasoline etc; otherwise surface of the A/C and even the whole A/C will be damaged.
- Prevent water from spattering in the A/C.
FILTER SCREEN
- Wash the filter screen once every two weeks. If it is blocked by dust, efficiency of the A/C will be reduced.
- Take out the air inlet grille and pull out the filter screen at both sides according to the direction shown in the following figures.
- Put the filter screen into the warm water (about 40°C or 104°F) added with neutral detergent, dry it at a shady place after cleaning.
SEASONAL CLEANING
If the A/C will not be used for a long time:
- Pull out the water plug to drain.
- Run the A/C in fan mode for 2H till the inside is dry.
- Turn off the A/C and unplug.
- Wash the filter screen and reassemble it.
- Dismantle the exhaust duct and keep it properly.
- Cover the A/C with a plastic bag and place it at a dry place.
Common Failures and Diagnosis
Intelligent Error Detection
Error-detecting code |
Multi-functional defection |
---|---|
E1 |
Error of the coil’s temperature sensor |
E2 |
Error of indoor temperature sensor |
E4 |
Anti-freezing protection: temperature of the coil is too low and the whole A/C is off. When temperature excesses 8°C or 46.4°F, the protection is released and previous working state is recovered. |
Troubleshooting
In case of any of the following trouble, please contact professional maintenance personnel in time.
TROUBLE |
CAUSE |
SOLUTION |
---|---|---|
The A/C doesn’t work |
No display |
Reset circuit breaker on AC cord |
The display panel displays “FL” |
Restart the A/C after power off and draining, then it will become normal |
|
Time OFF function is started |
The A/C can be restarted 3 minutes after being turning off. |
|
The A/C starts frequently |
Direct sunlight |
Draw the curtain |
Doors and windows keep open; there are lots of people or heat source in room |
Close doors and windows, remove heat source |
|
Filter screen is very dirty |
Clean or replace it |
|
Air inlet or air outlet is blocked |
Remove the stem |
|
Big noise of the A/C |
The A/C is placed unevenly |
Place it at even and firm ground, avoid shaking |
The compressor doesn’t work |
Its delay protection is started |
Wait for 3min., turn on after temperature decreases |
Notice: When there is any abnormal to the A/C, turn it off and unplug, and then contact professional maintenance personnel.
The above technical parameters are subject to change without notice.
Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities. Contact you local government for information regarding the collection systems available. If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the groundwater and get into the food chain, damaging your health and well -being. When replacing old appliances with new ones, the retailer is legally obligated to take back your old appliance for disposals at least free of charge.