Loading ...
Loading ...
Loading ...
4
because strong draughts of air may adversely aect the
equipment’s operational eciency.
- Only use the heater in an upright position.
- Use the appliance only on a stable and at oor.
- The heater must be positioned at least 80cm from furniture
or other objects (see g. 3-4).
- The rst time you use the appliance, operate it of at least 15
minutes with the thermostat at maximum to eliminate the
“new” smell. A little smoke due to the protective substances
applied to the heating element before transport may be
given o, for this reason we suggest you ventilate the room
during this operation.
- Do not position the appliance on long hair carpets, in order
to avoid obstruction to the air intake grille located under it.
- Do not obstruct the hot air outlet grilles or the air intake
grille on the bottom of the appliance.
- Position the appliance so that the plug and the outlet can
be easily reached even after installation.
- Do not use the appliance in rooms less than 4m
2
in
area.
- A tip over safety device turns the appliance o if it falls
over or is positioned inappropriately in such a way as to
jeopardise safety. The appliance emits a beep and a dot
ashes on the display. The appliance resumes operation
a few seconds after being placed in an upright position
again. See troubleshooting session.
- The appliance is tted with a safety device which will
switch the appliance o in case of accidental overheating.
To reset, disconnect the plug from the power socket for a
few minutes, remove the cause of overheating then plug
the appliance in again. If this abnormal situation happens
several times, please contact the customer service.
- For appliances provided with fans, means for ventilation
or ducting are provided in accordance with the installation
instructions.
DESCRIPTION
A Power indicator light
B ON/STAND-BY button
C +/- adjustment buttons
D MODE button (selects the operating mode)
E “ECO plus” button
F Timer button
Fundamental recommendations regarding safety
Dear Customer – The plug on this appliance will get ‘warm’
during use, this is perfectly normal.
This product is A HIGH POWER HEATING APPLIANCE designed to
our usual high standards but please make sure your wall
sockets are in good condition and the plug is inserted correctly
to avoid any accidental overheating. We suggest that you check
the plug AND THE SOCKET regularly if the heater is in prolonged
use, if you are in any doubt please consult an electrician.
General instructions
Remove the heater from the packaging. Check that neither the
heater nor the power cable has been damaged during transport.
Do not operate the heater if damaged. Remove all publicity
material present on the appliance. The appliance is suitable for
free-standing or wall-mounted usage. Do not assemble the feet
if wall-mounted.
Electrical connection
- Before connecting the appliance to the current outlet,
check that the voltage indicated on the appliance rating
plate is the same as your electric plant and that it can stand
the power consumption (Watt) indicated by the labelling.
- If more than one appliance is used at once, it is important to
ensure that the electric plant is able to support the power
required.
Mounting the feet
Turn the appliance upside down on a rug or soft surface in order
to prevent damaging the paint nish.
Fix the feet to the appliance with the nr. 4 screws supplied
(see g. 1), 2 screws for each foot.
Wall-Mounting Installation
The wall mounting kit contains:
4 metal brackets ( Fig. 2 A)
2 screws 4,8x13 PH (Fig. 2 B)
4 screws 4,5x25 PH (Fig. 2 C)
4 plastic anchors 6x30 (Fig. 2 D)
Required tools for assembly and estimated assembly
time
Screwdriver PH 2 x 100 (Phillips type supplied)
Estimated assembly time: 30 minutes
Before installing the unit , make sure of the following:
a. The appliance must not be located directly beneath
a current outlet.
b. The plug and outlet must be easy to reach after
installation.
c. No electric cables or other pipes could be damaged
during the installation.
d. Keep away from curtains or ammable materials.
Loading ...
Loading ...