Loading ...
Loading ...
Loading ...
10
CLEANING SAFEGUARDS
• AFTER MAKING A NUTRIBLAST OR SOUPERBLAST, THE BLADE MUST BE
CLEANED IMMEDIATELY.
• ALWAYS UNPLUG POWER BASE AND DEPRESS THE POWER BUTTON PRIOR TO
CLEANING, ASSEMBLING OR DISASSBMBLING.
• NEVER SUBMERGE THE POWER BASE IN WATER OR PLACE IT IN THE
DISHWASHER. WIPE OFF ANY DEBRIS INSIDE THE POWER BASE IMMEDIATELY
TO KEEP IT IN GOOD WORKING ORDER.
• DO NOT WASH THE BLADES IN THE DISHWASHER AS ELEVATED
TEMPERATURES CAN DAMAGE GASKET SEALS.
• THE NUTRIBULLET Rx CUPS CAN BE WASHED IN THE DISHWASHER AND
SHOULD BE WASHED ON THE TOP RACK OF THE DISHWASHER USING THE
NORMAL (NOT SANITIZE) CYCLE.
• THE NUTRIBULLET Rx CUPS AND BLADES SHOULD NOT BE EMMERSED IN
BOILING WATER FOR ANY REASON AS THIS WILL WARP PLASTIC AND
DAMAGE GASKETS.
• BLADES ARE SHARP! USE CARE WHEN CLEANING BLADES TO AVOID INJURY!
RINSE BLADES IMMEDIATELY AFTER EACH USE TO PREVENT DEBRIS FROM
DRYING AND STICKING TO BLADE COMPONENTS. IF NECESSARY, USE
INCLUDED BRUSH TO LOOSEN ANY DEBRIS AROUND BLADES, GASKETS AND
BLADE HOUSING THREADS WITH CARE.
• HANDWASH ONLY WITH MILD DISH SOAP AND WARM WATER (NOT HOT).
• DRY IMMEDIATELY.
• FOR TOUGH DEBRIS, FILL THE CUP ½ FULL WITH WARM (NOT HOT), MILD
SOAPY WATER. THEN, SIMPLY TWIST ON THE BLADE, POP IT ON THE BASE
AND GIVE IT A RUN FOR 30-45 SECONDS. FOLLOW UP WITH A QUICK BRUSH.
• WHEN WASHING BLADES, DO NOT ATTEMPT TO REMOVE THE GASKET RING.
SIMPLY HAND WASH THE BLADES IN WARM, MILD SOAPY WATER. ATTEMPTED
REMOVAL OF THE GASKET MAY PERMANENTLY DAMAGE THE BLADE
CONFIGURATION AND CAUSE LEAKAGE. IF IN TIME A GASKET BECOMES LOOSE
OR DAMAGED, PLEASE CONTACT CUSTOMER SERVICE FOR A REPLACEMENT
NUTRIBULLET Rx BLADE HOLDER AT: 1-844-696-2791.
STUBBORN CLEANUP
• If ingredients dry inside the NutriBullet Rx Cups or SouperBlast Pitcher, make
your cleanup a snap by filling the cup about 2/3 full with warm soapy water and
screw on the Extractor Blade and if using the SouperBlast Pitcher, put on
lids. Place the cup assembly on the NutriBullet Rx Power Base for about 20-30
seconds. That will loosen the stuck ingredients, and with a light scrub and rinse,
you’ll be all done.
CLEANING THE NUTRIBULLET Rx
POWER BASE
For the most part the Power Base doesn’t really get dirty, but if you neglect to
twist the blade on to the cup tightly, liquids can leak out and get into the base and
activator buttons.
Here’s how to clean it up.
Step 1: The most important thing is to UNPLUG the Power Base before cleaning!
Step 2: Use a damp rag to wipe down the inside and outside of the Power Base.
• NEVER SUBMERGE THE POWER BASE IN WATER OR PLACE IT IN THE
DISHWASHER.
• Never put your hands or utensils near the moving blade and never use your hands
or utensils to press the activator buttons down while the Power Base is plugged in.
HEAVY CLEANING:
• Should the inside of the base become sticky due to spillage you may follow these
additional cleaning instructions:
• UNPLUG the Power Base and depress the power button BEFORE cleaning.
• Place the Power Base on a dish towel to catch any liquid or debris.
• Pour a scant 1/8 cup of a dilute solution of distilled vinegar and warm (not hot)
water (1 part vinegar to 2 parts water) in to the Power Base where the blade
assembly would sit during normal use.
• Immediately use a dish brush to dislodge any debris and wipe it out with a damp cloth.
• The Power Base is constructed with a drain tube to drain any liquid debris safely
through to the dish towel without damaging the inside components.
SAVE THESE INSTRUCTIONS
FOR HOUSEHOLD USE ONLY
11
Loading ...
Loading ...
Loading ...