Loading ...
Loading ...
Loading ...
8 9
SAFETY WARNINGS FOR
EXTRACTING FOR SOUPS
• WARNING!: ONLY USE THE VENTED SOUPERBLAST PITCHER AND TWO-PIECE
LID WHILE OPERATING THE NUTRIBULLET Rx IN SOUPERBLAST MODE. THE
SOUPERBLAST PITCHER IS SPECIALLY VENTED TO RELEASE PRESSURE AS THE
SOUP MIXTURE HEATS. OTHER VESSELS ARE UNVENTED AND MAY RUPTURE
AND CAUSE PERSONAL INJURY IF MISUSED IN SOUPERBLAST MODE.
• TO PREVENT OVERHEATING: DO NOT REPEAT SOUPERBLAST MODE FOR THE SAME
HOT SOUP. IF MORE HEAT IS REQUIRED, PLACE THE CONTENTS IN A MICROWAVE-
SAFE CONTAINER AND CONTINUE HEATING TO DESIRED TEMPERATURE. TO
MAKE A NEW SOUP, EMPTY OLD CONTENTS, ADD NEW INGREDIENTS AND WAIT
1 FULL MINUTE BEFORE RETURNING THE VESSEL TO THE POWER BASE TO START
A NEW SMART TECHNOLOGY CYCLE. DO NOT REPEAT MORE THAN 2 CYCLES IN
SOUPERBLAST MODE RESTING 1 MINUTE BETWEEN CYCLES.
• DO NOT RUN THE NUTRIBULLET IN SOUPERBLAST MODE FOR MORE THAN 2 CYCLES
CONSECUTIVELY WITHOUT ALLOWING THE NUTRIBULLET POWER BASE AND
SOUPERBLAST ACCESSORIES COOL OFF FOR 30-60 MIN. TO PREVENT OVERHEATING
AND ALLOW INGREDIENTS TO SETTLE BEFORE CONTINUING TO BLEND.
• IF POWER BASE DOES NOT SHUT OFF AFTER ONE (1) 7-MINUTE INTERVAL
DURING SOUPERBLAST MODE, DEPRESS THE POWER BUTTON, LOCATED 90˚ TO
THE LEFT SIDE OF THE G-BUTTON OR SIMPLY LIFT THE SOUPERBLAST PITCHER
OFF OF THE POWER BASE.
• ALLOW POWERBASE TO SHUT OFF COMPLETELY AFTER INITIAL INTERVAL AND
WAIT FOR 3-4 MINUTES BETWEEN INTERVALS.
• POWER BASE IS EQUIPPED WITH AN INTERNAL THERMAL BREAKER THAT
SHUTS OFF THE POWER BASE WHEN THE UNIT OVERHEATS. IF THE POWERBASE
OVERHEATS AND SHUTS OFF, UNPLUG THE POWER BASE OR PRESS THE POWER
BUTTON, LOCATED 90˚ TO THE LEFT OF THE G-BUTTON AND LET IT COOL FOR
AN HOUR OR MORE BEFORE ATTEMPTING TO USE IT AGAIN. POWER BASE WILL
RESET WHEN THE UNIT IS POWERED OFF AND THE THERMAL BREAKER HAS
COOLED DOWN SUFFICIENTLY.
HEAT CAUTION!
• DURING SOUPERBLAST MODE, THE CONTENTS INSIDE CAN REACH UP TO
ABOUT 70ºC / 150ºF THROUGH THE FRICTION OF THE ROTATING BLADE.
• KEEP HANDS AND OTHER EXPOSED SKIN AWAY FROM THE LID OPENING TO
PREVENT POSSIBLE BURNS DURING SOUPERBLAST MODE.
• DO NOT REMOVE THE LID DURING PROCESSING OF SOUP—INGREDIENTS WILL
BECOME HOT AND MAY SPLASH OUT AND CAUSE INJURY.
• DO NOT TOUCH SOUPERBLAST PITCHER DIRECTLY WITH HANDS AFTER
SOUPERBLAST MODE! THE SOUPERBLAST PITCHER SURFACE, BLADES AND
COUPLING GEAR WILL BE HOT!
• ALWAYS USE APPROPRIATE HEAT RESISTANT PADS ON THE HANDLE TO HOLD THE
SOUPERBLAST PITCHER AND TO SUPPORT THE BOTTOM OF THE CONTAINER.
• CAREFULLY OPEN SOUPERBLAST PITCHER LID AFTER SOUPERBLAST MODE,
AS ESCAPING STEAM AND MOISTURE MAY CAUSE SCALDING BURNS.
• Always attach blade to SouperBlast Pitcher and hand tighten or use the blade remover to
tighten the blade to prevent leakage prior to adding ingredients into the pitcher.
• NEVER USE THE EXTRACTOR BLADE TO BLEND WITHOUT LIQUID AS DOING SO
MAY DAMAGE THE BLADE.
• Do not use the soup pitcher on the motor base without the black lid and clear vent top
in place when running the NutriBullet Rx.
• TO TURN THE NUTRIBULLET ON IN SOUPERBLAST mode using SMART Technology,
plug the power base into an electrical outlet. Press the power button, located 90˚ to
the left side of the G-button. The power button will glow BLUE, signifying the power
is on. Next, place the cup blade-side-down onto the power base. This will activate the
NutriBullet Rx’s SMART TECHNOLOGY function, causing the G-Button at the front of
the unit to glow GREEN.
• Press the GREEN G-Button down for 2 seconds until it glows RED. This will indicate
that SouperBlast mode has begun. The unit will run in SouperBlast mode for about 7
minutes before automatically turning off. Once off, simply lift the SouperBlast Pitcher
off of the Power Base.
• The motor will run 3 cycles during the 7 minute program—it will slow down twice
through the cycle to allow the ingredients to settle for improved processing then
it will increase again for the next part of the cycle. This is a normal function of the
NutriBullet Rx.
• The contents inside can reach up to about 70ºC / 150ºF through the friction of the rotating blade.
• If you wish to process your soup for less than the programmed time, you may simply
lift off the SouperBlast Pitcher or press the power button, located 90˚ to the left side of
the G-button.
• Always allow it to come to a complete stop prior to adding additional ingredients
during the processing period.
• Always depress the power button when not in use. The BLUE light will stop glowing,
signifying the power is off.
Loading ...
Loading ...
Loading ...