© Copyright 2007, LG Electronics U.S.A., Inc.
Installation and Operating Guide | Warranty
Model Numbers | L26W56SA • L26W56BA • L26W56WA | LCD TV/Monitors
page
5
t a b l e o f c o n t e n t s
page
60
installer quick setup guide
Zenith and the lightning Z logo are registered
trademarks of Zenith Electronics Corporation
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED
SERVICE PERSONNEL.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
THIS PRODUCT MUST BE USED WITH UL LISTED MOUNTING BRACKET.
IT IS FORBIDDEN TO CONNECT THIS TV TO ANY TELECOMMUNICATION NETWORK / TELEPHONE.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature accompanying the appliance.
NOTE TO CABLE TV INSTALLER:
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code
provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of
the building, as close to the point of the cable entry as practical.
REGULATORY INFORMATION:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
Marketed and Distributed in the United States by LG Electronics U.S.A., Inc.
2000 Millbrook Drive, Lincolnshire, IL 60069.
For Customer Support/Service please call:
1-888-865-3026
www.zenith.com
www.lgcommercial.com
RECORD THE MODEL NUMBER
The model and serial number of this LCD TV/Monitor are
located on the back of the cabinet. For future reference,
we suggest that you record the serial number here:
MODEL NO. L26W56SA, L26W56BA, L26W56WA
SERIAL NO.____________________________________
PAGE 3
CAUTION:
Do not attempt to modify this product in any way without written authorization from Zenith Electronics Corporation.
Unauthorized modification could void the user’s authority to operate this product.
COMPLIANCE:
The responsible party for this product’s compliance is:
LG Electronics U.S.A., Inc.,
2000 Millbrook Drive
Lincolnshire, IL 60069, USA.
Phone: 1-847-941-8000
WARNING:
Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall not be placed on the
apparatus.
CAUTION:
THESE SERVICING INSTRUCTIONS ARE FOR USE BY QUALIFIED SERVICE PERSONNEL ONLY. TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN THE OPERATING INSTRUCTIONS UNLESS YOU ARE
QUALIFIED TO DO SO.
CAUTION:
When used outside of the U.S., it may be used HAR cord with fitting of an approved agency is employed.
(When used outside of U.S., other power supply cords may be used if the cord is approved by the local regulating agency.)
CLEANING AND DISINFECTION:
Clean the exterior of this television by removing dust with a lint-free cloth.
CAUTION: To avoid damage to the surface of the television, do not use abrasive or chemical cleaning agents.
IMPORTANT SAFEGUARDS FOR YOU AND YOUR NEW PRODUCT
YOUR PRODUCT HAS BEEN MANUFACTURED AND TESTED WITH YOUR SAFETY IN MIND. HOWEVER, IMPROPER USE CAN RESULT IN
POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. TO AVOID DEFEATING THE SAFEGUARDS THAT HAVE BEEN BUILT INTO YOUR NEW
PRODUCT, PLEASE READ AND OBSERVE THE FOLLOWING SAFETY POINTS WHEN INSTALLING AND USING YOUR NEW PRODUCT, AND SAVE
THEM FOR FUTURE REFERENCE. OBSERVING THE SIMPLE PRECAUTIONS DISCUSSED IN THIS MANUAL CAN HELP YOU GET MANY YEARS OF
ENJOYMENT AND SAFE OPERATION THAT ARE BUILT INTO YOUR NEW PRODUCT.
Notes
- If the TV feels cold to the touch, there may be a small “flicker” when it is turned on. This is normal, there is nothing wrong
with the TV.
- Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they have no
adverse effect on the TVs performance.
- Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce some
temporary distortion effects on the screen.
PAGE 4
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that
produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider
than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is
provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where
they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart
is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been spilled or object have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate normally, or has been dropped.
Outdoor Antenna Grounding
If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to
provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code (U.S.A.),
ANSI/NFPA 70 provides information with regard to proper grounding of the mast and supporting structure, grounding of the
lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to
grounding electrodes, and requirements for the grounding electrode.
Example of Grounding According to National Electrical Code Instructions
IMPORTANT SAFETY INSTRUCTIONS
Antenna Lead in Wire
Antenna Discharge Unit
(NEC Section 810-20)
Grounding Conductor
(NEC Section 810-21)
Ground Clamps
Power Service Grounding
Electrode System (NEC
Art 250, Part H)
Ground Clamp
Electric Service
Equipment
NEC - National Electrical Code
PORTABLE CART WARNING
Table of Contents
PAGE 5
Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . .2-3
Important Safety Instructions . . . . . . . . . . . . . . . . . . .4
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Step 1. LCD TV/Monitor Installation and Connections
Setup Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Installation/Connections Overview . . . . . . . . . . . . . . . .7
VESA Standard TV Mounts . . . . . . . . . . . . . . . . . . . . . .8
TV and other Equipment Hookup
Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Cable Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Antenna & VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Cable Service with VCR . . . . . . . . . . . . . . . . . . . . . .12
S-Video (DVD-VCR) . . . . . . . . . . . . . . . . . . . . . . . . .13
Component Video (DVD) . . . . . . . . . . . . . . . . . . . . . .13
DVI Hookup To RJP100 or DVD Player . . . . . . . . . . . . .14
Computer PC Hookup . . . . . . . . . . . . . . . . . . . . . . . .14
Power Cord Hookup . . . . . . . . . . . . . . . . . . . . . . . . .15
Front Panel Controls . . . . . . . . . . . . . . . . . . . . . . . 16
Menus and Displays Overview
On-Screen Menus Overview . . . . . . . . . . . . . . . . . . . .17
Other Menus and On-Screen Displays . . . . . . . . . . . . . .18
User Remote Control Key Functions . . . . . . . . . . . . . . .19
Installer Remote Control Key Functions . . . . . . . . . . . .20
Step 2. Channel Search and Reception Setup
Auto Program (Do a Channel Search) . . . . . . . . . . .21
Channel Menu
Channel List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Channel Labels Setup . . . . . . . . . . . . . . . . . . . . . . . 23
Step 3. Customize the TV’s Features
Setup Menu
Clock Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Menu Language . . . . . . . . . . . . . . . . . . . . . . . . . . .27
V-Chip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28-31
Caption Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Sound Menu . . . . . . . . . . . . . . . . . . . . . . . . . . 34-35
Picture Menu . . . . . . . . . . . . . . . . . . . . . . . . . .36-37
Installer Overview . . . . . . . . . . . . . . . . . . . . . . . . .38
Commercial Mode Setup . . . . . . . . . . . . . . . . . . . . . .39
Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49-56
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . .56-57
TV Operating Check . . . . . . . . . . . . . . . . . . . . . . . . .58
Glossary of Terms . . . . . . . . . . . . . . . . . . . . . . . . . .59
Installer Quick Setup Guide. . . . . . . . . . . . . . . . . . . .60
Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61-63
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
The table of contents lists the pages to go to for setting up the features for the end user.
Optional Installer Remote Control for Model No. L26W56XA
Shown herein is an optional Installer remote control available for the L26W56XA model only. The
remote control is NOT included with the LCD TV/Monitor. However, the user's remote is included with
the TV.
Purchase the Optional Installer's Remote and Clone Programmer
To perform a normal installation set up, you need an installer's remote and the LT2002 Quickset II Clone Programmer –
both are shown and described in later sections. See your Zenith/LG dealer if you wish to purchase the Installer remote and
LT2002. The installer remote allows access to the Installer menus, User menus in the Manual Channel Set options on the
Setup menu. The installer remote has Menu, Select, and Adjust Keys. The LT2002 Quickset II Clone Programmer is used to
duplicate a TV's setup and install it on another identical TV.
*Note: Design and specifications are subject to change without prior notice.
PAGE 6
Installation Overview
• Unpack the LCD TV/Monitor and all
accessories.
• Determine installation location for the
LCD TV/Monitor, TV stand or mount.
• Determine mounting and installation
requirements. If used, AC Power
source outlet, Antenna/Cable service
connectors, any external equipment
required for system or TV operation,
all necessary cables, wires, connectors
and any other additional required
hardware, etc.
Installation Overview & System Setup:
Questions to Consider Before
Installation
VESA Bracket
Does the VESA Bracket have to be
mounted to the TV? Y: Install VESA
Bracket on TV following the instructions
supplied with the bracket.
Yes___ No___
TV Stand
Does the TV have to be mounted on the
stand? Y: Mount the TV on the stand
following the instructions provided with
the TV stand.
Yes___ No___
Installer's Remote Control
Does the Installer have an the optional
Installer's remote control available to
use to set up the TV (This is a must for
TV setup.)?
Yes___ No___
Master TV Setup
Will the Master TV's features setup be
cloned and be copied to other identical
LCD TV/Monitors?
Yes___ No___
LT2002 Quickset II Clone Programmer
To copy the TV's setup, the installer will
need a clone programmer. Is there a
Zenith LT2002 Clone Programmer
available?
Yes___ No___
End-User Remote Control
Will a remote control be provided to the
end user to operate the TV? (The remote
is included with the TV.)
Yes___ No___
End-User Menu Access
Will the end-user have access to all the
menus on the TVs from the front panel?
Yes___ No___
LCD TV/Monitor Setup Checklist
1. Install the LCD TV/Monitor where it
will be used.
Prior to Operation
The LCD TV/Monitor must be connected
to all external antenna/cable, video, and
audio source equipment. and a AC power
source. See page 5, Table of Contents.
2. Make all external source equipment
connections. See pages 10 - 15.
3. Connect the LCD TV/Monitor to a
standard 120V, 60 Hertz, AC power
source. See page 15.
4. Turn on the TV and all source
equipment.
Review TV Setup Options in the
Installer's Menu Section
The Installer's menu includes a number
of options for the master TV's setup that
enable the installer or system
administrator to devise a unique system
using the many different options and
variables available. See Installer's menus
section.
Master TV Features Setup for Cloning
Overview
• Set up Installer's remote control, see
page 20.
• Do a Channel Search, see page 21.
• Channel List.
• Channel Label.
• Video/picture appearance options
setup, see Picture menu.
• Audio/sound options setup, see Sound
menu.
• Set up all other features. See page 5,
Table of Contents, for a list of features
available on this LCD TV/Monitor.
Clone Master TV's Setup
See Clone Programmer section.
Setup Checklist
PAGE 7
M.P.I. INTERFACE
Use with clone programmer.
FUTURE USE
DVI/PC AUDIO IN
PC IN
HDMI/DVI IN
DIGITAL AUDIO OUT
(Optical)
RS-232C PORT
RS-232C SELECT
SWITCH
UPDATE
SWITCH
ANTENNA CABLE
Connect to an antenna or
cable system.
S-VIDEO IN
AUDIO / VIDEO 1, 3 IN
Connect Audio / Video
equipment to these jacks.
COMPONENT 1, 2 IN
AC IN
RJP INTERFACE
To hook up source equipment, see below and also refer to the Table of
Contents on page 5; shows pages to go to for equipment hookup options.
VIDEO2(SIDE AUTO-CAMPORT)
VIDEO IN AUDIO IN
LR
AUDIO/
VIDEO 2
(SIDE AUTO-
CAMPORT)
*Note: RS-232C, Update Switch and RS-232C Select Switch are reserved for qualified and autho-
rized service and technical support personal only.
Installation/Connections Overview
VESA Standard TV Mounts
PAGE 8
Swivel Stand
- The TV can be conveniently
swiveled on its stand 30° to
the left or right to provide
optimum viewing angles.
There are several Vesa standard
mounts available that can be used
with this TV. The mount shown to the
right would be installed on the TV
back using required bolts in the four
pre-threaded holes provided.
Follow any instructions supplied with
the Vesa mount if one is to be used
for the TV installation.
TV Swivel Stand
Vesa Standard
Mounting Holes
Typical
Vesa
Mount
Antenna Hookup
PAGE 9
Mini glossary
75 OHM RF CABLE The wire that comes from an off-air antenna or cable service provider. Each end looks like a hex shaped nut with a wire sticking
through the middle, and it screws onto the threaded jack on the back of the TV.
A small device that connects a two-wire 300 ohm antenna to a 75 ohm RF jack. They are usually about an inch long with two screws
on one end and a round opening with a wire sticking out on the other end.
1
2
3
RF Coaxial Wire
(75 ohm)
300/75 ohm
Adapter
Connections Panel
Connections Panel
Locate the Antenna/Cable jack on the back
of the LCD TV/Monitor.
Connect the antenna wire (Flat or Round)
that runs from the wall to this jack,
according to one of the diagrams shown to
the right.
After all connections are complete, plug in
the TV. The LCD TV/Monitor is designed to
operate on AC power.
Flat Wire
(300 ohm)
Connect an off-air antenna to the LCD TV/Monitor.
If the antenna is a 75 ohm RF cable, then no
adapters are required.
A 300 to 75 ohm adapter is not included with
the Zenith LCD TV/Monitor.
300 TO 75 OHM
ADAPTER
Cable Service Hookup
PAGE 10
Locate the Antenna/Cable jack on the
back of the TV.
Connect the cable wire to the
Antenna/Cable jack according to one
of the diagrams to the right.
After all connections are complete,
plug in the TV. The LCD TV/Monitor is
designed to operate on AC power.
1
2
3
Connections Panel
Cable TV
Wall Jack
RF Coaxial Wire
(75 ohm)
Cable TV
Wall Jack
Coaxial Wire
RF (75 ohm)
Connections Panel
Connect cable service to the LCD TV/Monitor.
Mini glossary
75 OHM RF CABLE The wire that comes from an off-air antenna or cable service provider. Each end looks like a hex shaped nut with a wire sticking
through the middle, and it screws onto the threaded jack on the back of the TV.
A small device that connects a two-wire 300 ohm antenna to a 75 ohm RF jack. They are usually about an inch long with two screws
on one end and a round opening with a wire sticking out on the other end.
300 TO 75 OHM
ADAPTER
For cable box operation, leave the television
tuned to channel three or four and use the
cable box to change channels.
Antenna & VCR Hookup
PAGE 11
300/75ohm
Adapter
VCR Back Panel
Round
or
Flat wire
(300 ohm)
Locate the Antenna/Cable jack on
the back of the VCR.
Connect the antenna wire that runs
from the wall jack to the VCR.
Connect other wires according to
the diagram to the right.
After all connections are complete,
plug in the TV. The LCD TV/Monitor
is designed to operate on AC power.
1
2
3
Connect antenna and a VCR to the LCD TV/Monitor.
Connections Panel
Cable Service with VCR Hookup
PAGE 12
Locate the Antenna/Cable jack on the
back of the VCR.
Connect the cable service wire to the VCR.
Connect other wires according to the
diagram to the right.
After all connections are complete, plug
in the TV. The LCD TV/Monitor is designed
to operate on AC power.
1
2
3
Cable Box
Cable TV
Wall Jack
Cable TV
Wall Jack
Connections Panel
VCR AV Panel
Connect cable service and a VCR to the LCD TV/Monitor.
For cable box operation, leave the VCR
and the television tuned to channel
three or four and use the cable box to
change channels.
S-Video Hookup (DVD-VCR)
Component Video Hookup (DVD)
PAGE 13
Locate the S-Video out port on the DVD
or VCR.
Connect an S-Video cable between the
DVD player and S-Video In on the TV.
Make R - L Audio connections as indicated
to the right.
After all connections have been made,
select the S-Video source to display the
DVD image on the TV.
1
2
3
Locate the component out jacks on
the DVD player.
Connect component video cables
between the DVD player and
Component 1 or 2 In on the TV.
Make R - L Audio connections as
indicated to the right.
After all connections have been made,
select the Component 1 or 2 source to
display the DVD image on the TV.
1
2
3
S-Video/R-L Audio
cables are not included
with TV
DVI Hookup To RJP100 or DVD Player
PAGE 14
Computer PC Hookup
Locate the DVI out port on
the RJP100M or DVI device.
Connect a DVI cable
between the RJP100M and
DVI in port on the TV.
If required, make Audio
connections as indicated to
the right.
After all connections have
been made, select the DVI
source to display the DVI
image on the TV.
1
2
3
Locate the computer out port
on the computer.
Connect a computer cable
between the computer and PC
In on the TV.
Make PC Audio connections as
indicated to the right.
After all connections have
been made, select the PC
source to display the PC image
on the TV.
1
2
3
Power Cord Hookup
PAGE 15
AC Power Cord Hookup
The LCD TV/Monitor is designed to operate on
120V AC power.
Locate the AC Power Cord input socket on the
back of the LCD TV/Monitor.
Insert the AC power cord connector into the
AC Socket on the TV as shown below.
1
2
Connect the AC power cord directly to the LCD TV/Monitor.
AC Power Cord
Front Panel Controls
PAGE 16
/ I
Remote Control Sensor
Power / Standby Indicator
Glows red in Standby mode.
Glows green when the TV is
turned on.
Glows orange in Sleep Timer
and/or Alarm mode.
A
B
C
D
E
Using the front control panel to operate the LCD TV/Monitor.
LED Color Action/Status
RED Power is Off (Standby)
GREEN is flashing Power On sequence is processing
GREEN Power is On
ORANGE If Power is Off On Timer is set or Alarm is set
If Power is On Off Timer is set or Sleep Timer is set
TV Operation
Press the POWER button to turn the LCD TV/Monitor on
from standby mode.
Press MENU repeatedly to scroll through menus.
*Note: With Installer menu item 11 Key Defeat set to 000
(the default setting), Menu and TV/AV keys are disabled.
Displays the current channel bank. Press again to
change banks.
Use the CH (Channel) Up/Down button to cycle through
the available channels.
Use the VOL (Volume) Up/Down button to adjust the
sound level to your preference.
On-Screen Displays
See descriptions on page 18. On-screen displays will
appear when the feature is active or the function is
being used.
A
B
CDE
On-Screen Menus Overview
PAGE 17
ON-SCREEN MENUS
CHANNEL MENU Adjusts the basic operational features of the TV.
Auto Program 21 Automatically finds and stores active channels to scroll through using Channel Up/Down.
Channel List 22 Manually picks and chooses which active channels will appear when using Channel Up/Down.
Channel Label 23 Labels the channels with their network names (ABC, CBS, HBO, etc.).
Fine Tune Automatically adjusts the picture for optimum appearance.
Signal Strength Reveals the strength of the incoming digital signal.
SETUP MENU
Time 24 Sets the time.
V-Chip 28 Sets up restrictions or changes the password for Parental Control.
PC With computer connected, sets up PC image appearance.
Menu Language 27 Picks the language the on-screen menus will appear in.
Menu Transparency Selects the degree of menu opacity.
Set ID Specifies the TVs identity.
CAPTION MENU 32 Chooses analog and digital captioning options.
SOUND MENU 34 Sets up the sound.
Options are: Mode, Balance, Digital Output, Auto Volume, Multi-Track, Internal Speaker.
PICTURE MENU 36 Sets up the picture appearance.
Options are: Mode, Color Temperature, Screen Format, Noise Reduction, Film Mode.
18 OTHER MENUS AND ON-SCREEN DISPLAYS
Volume Shows current sound level.
Sleep Timer Sets a time the TV will turn off.
SAP Selects MTS sound: Mono, Stereo, and SAP in analog mode. Change the audio language in DTV mode.
Captions Selects Caption/Text options.
Alarm Set a time for the TV to turn itself on.
Guide View DTV program information.
Channel Preview -> V-Chip Displays the available TV channels and guest’s Parental Control menu.
Info Shows program details: Title, Broadcast Time, Signal Format, Signal Strength CC, V-Chip, Language, Sound
Format, Time, Date, Channel Icon, Channel Label.
INSTALLER MENUS
Installer Menus 41 Makes adjustments to the TV’s operational features.
Menu Name Page Description
Descriptions of the menus and on-screen displays.
Other Menus & On-Screen Displays
PAGE 18
Use the remote keys indicated below to access these menus and displays.
In this manual, the OSD (On Screen Displays shown) may be different than those on the actual TV.
The following are generic examples to familiarize you with the TVs options.
19 Off
1
2
6
9
3
TIMER
Volume Display
Press VOLUME.
Shows currently selected sound setting.
Sleep Timer Menu
Press TIMER.
Sets a time to automatically turn the TV off
and shows remaining time before TV shutoff.
Service1
CAPTION
SAP Display
Selects MTS sound: Mono, Stereo, and
SAP in analog mode. Change the audio
language in DTV mode.
Caption Display
Press CC.
Turns selected option on or off. See
Closed Captions page to select options.
Alarm Timer
Current Time 11:17 AM
Exit
AdjustMove
OK
Hr.
Off
Min.
Alarm Display
Press ALARM.
Set a time for the TV to turn itself on.
Channel
Channel List (1/1)
ANALOG 14
ANALOG 15
ANALOG 16
DIGITAL 7-1
DIGITAL 11-1
DIGITAL 84-1
DIGITAL 88-1
Add
Move Add/Del
View
OK
V-Chip
CC
CH PREVIEW
EXIT
Antenna
Auto Program
Channel Label
Channel List
Fine Tune
Signal Strength
-- : -- --
--. -- ----
Channel Preview
Press CH PREVIEW.
Displays available TV channels.
Setup
Enter your PIN.
----
0 9
CC
EXITNumber~
Time
V-Chip
PC
Menu Language
Menu Transparency
Set ID
-- : -- --
--. -- ----
V-Chip
Press CC.
Move to the V-Chip menu.
CURRENT GUIDECURRENT GUIDE
No Information
84-1
6/23 Fri
PM 2:25
No Information
Guide Display
Press GUIDE to view DTV program
information.
DIGITAL 84-1
No Time Information
No Title
N/A
1920*1080@60Hz Korean N/A
Dolby Digital
INFO
Press INFO.
Check the current program information.
English
SAP
User Remote Control Key Functions
PAGE 19
A list of the keys and their functions on the user remote control supplied with the LCD TV/Monitor.
POWERMUTE
TV/AV
CH
PREVIEW
GUIDE
SAP INFO
123
456
7
-
89
0
CC
TIMER
FLASHBK
CH
CH
VOL
OK
VOL
ALARM
MUTE
Turns sound Off and On, while the picture
remains.
GUIDE
Use to view DTV program information.
CC
Press to activate English subtitles.
ALARM
Use to go to the Alarm menu. Set a time
for the TV to turn itself on.
POWER
Turns TV On or Off.
TV/AV
Displays a menu of all available input
sources.
SAP
Selects MTS sound: Mono, Stereo, and SAP
in analog mode. Change the audio
language in DTV mode.
INFO
Check the current program information,
screen status, multi-sound status and time.
[-] BUTTON
When selecting a digital broadcast
channel, key in the Main channel
number followed by the-> [-] -> then the
sub channel number. Analog channels do
not contain a sub channel number.
VOLUME / CHANNEL / OK (Enter)
Increase or decrease the volume /
Change channels.
Select on-screen menu items and change
menu values.
NUMBER BUTTONS
Use for direct channel entry.
TIMER
Press repeatedly to select a preset time to
automatically shut the TV off.
CHANNEL PREVIEW
Displays available TV channels, and (if
active) the Guest Parental Control menu:
set V-Chip blocks to restrict both analog
and digital programming.
• Aux Channel allows the guest to select
the Audio / Video inputs. (Use the A/V
jacks on the back of the TV as a source).
FLASHBK (FLASHBACK)
Use to return to the last channel
viewed.
Optional Installer
Remote Control
Part Number
3140OSKZ001AR6
Installer Remote Control Key Functions
PAGE 20
A brief list of the keys on the optional installer’s remote and what they do.
MUTE
Turns sound Off and On, while the picture
remains.
CHANNEL (-/+)
Tunes to next available channel.
Enter (OK)
Press to view the Channel/Time display or
to remove any on-screen display or menu.
ALARM
Use to go to the Alarm menu. Set a time
for the TV to turn itself on.
CHANNEL PREVIEW
Displays available TV channels, and (if
active) the Guest Parental Control menu:
set V-Chip blocks to restrict both analog
and digital programming.
• Aux Channel allows the guest to select
the Audio / Video inputs. (Use the A/V
jacks on the back of the TV as a source).
MENU/SELECT/ADJ (Adjust)
Press to display the main on-screen menu.
Use SELECT to choose an option and ADJ
(adjust) Left/Right to change the selected
option.
Optional Patient
Remote Control
Part Number
6710V00108M
POWER
Turns TV On or Off.
TV/FM
Down arrow for navigating menus.
VOLUME (-/+)
Decreases/increases sound level.
NUMBER KEYPAD
Selects channels directly and enters
numerical values for some options.
TIMER
Press repeatedly to select a preset time to
automatically shut the TV off.
[-] BUTTON
When selecting a digital broadcast
channel, key in the Main channel
number followed by the-> [-] -> then the
sub channel number. Analog channels do
not contain a sub channel number.
CC (Closed Captioning)
Press to access closed captions.
FLASHBK (Flashback)
Returns to the previous channel viewed.
Auto Program (Channel Search)
PAGE 21
With the optional Installer remote control in hand, press
the POWER key to turn the TV on.
Press the MENU button and then use the D / E ADJ button
to select the Channel menu.
Press OK (Enter).
With Auto Program highlighted, press the OK (Enter)
button.
Press the OK (Enter) button to start the channel search.
After finding all available channels, a display appears
briefly showing the number of analog and digital channels
found.
Press the MENU button repeatedly to remove the menus.
1
2
3
4
5
6
Use Auto Program to automatically find and store all of
the channels available in the selected Tuning Band.
*Notes: Tuning Band must be set before doing the channel search. See
Installer menu item 003 Band/AFC. Default setting is 1, for CATV. When
Auto Program is run, any assigned channel labels are automatically
removed.
Auto Program finds channels being received
by the TV’s analog and digital tuners.
Cable will not work unless you subscribe to
a cable service.
Channel
Antenna
Auto Program
G
Channel Label
Channel List
Fine Tune
Signal Strength
--:-- --
--. -- ----
Antenna
Auto Program
Channel Label
Channel List
Fine Tune
Signal Strength
--:-- --
--. -- ----
Channel List
PAGE 22
Removing unwanted channels
Review the channels found, you may remove unwanted
channels.
Press the MENU button. Then use the
D / E
ADJ button to
select the Channel menu, then press the OK (Enter) button.
Use the
D / E
ADJ button to highlight Channel List, then
press the OK (Enter) button.
Use the
D / E
ADJ ADJ button to highlight the channel you
wish to delete, then press the ADJ G Right arrow button.
The right arrow toggles the check mark on and off. If the
check mark appears next to the channel number, the
channel appears in the channel scan.
Press the MENU button repeatedly to remove the menus.
1
2
3
4
After the channel search, remove unwanted channels.
Channel
Antenna
Auto Program
Channel Label
Channel List
G
Fine Tune
Signal Strength
--:-- --
--. -- ----
Channel
Channel List (1/1)
ANALOG 14
ANALOG 15
ANALOG 16
DIGITAL 7-1
DIGITAL 11-1
DIGITAL 84-1
DIGITAL 88-1
Add
Move Add/Del
View
OK
Menu
Back
Antenna
Auto Program
Channel Label
Channel List
Fine Tune
Signal Strength
--:-- --
--. -- ----
If you delete a found channel, it isn’t gone forever.
Simply re-enter the Channel List menu and re-add the
channel to show the check mark.
Channel Labels Setup
PAGE 23
Channel Labels help the user identify the channel or network being viewed.
In the Setup menu with the Channel Labels option highlighted, use the ADJ
Left/Right arrow to scroll through the available channel labels, such as,
A&E, AMC, ESPN, HBO, etc. These are a series of preset labels from which
you can choose the more common networks. Use any of these to label the
channels in the TV’s memory.
Channel Labels Setup
Operating the Channel Label Menu
Channel
Antenna
Auto Program
Channel Label
G
Channel List
Fine Tune
Signal Strength
--:-- --
--. -- ----
Note: If you add channel labels to existing channels, then re-run Auto
Program, the labels will all be deleted.
Press the MENU button and then use the D / E ADJ button
to select the Channel menu. Press the OK (Enter) button.
Use the
D / E
ADJ button to highlight Channel Labels,
then press the OK (Enter) button.
This action displays the Channel Labels menu.
Use Channel Up/Down to select channels and the
Up/Down Left/Right ADJ arrow buttons to navigate the
labels menu.
When the label is highlighted you want for the channel
shown in the screen, press OK (Enter) to add the label to
the channel.
Select the next channel to label with Channel Up/Down or
if finished channel labeling, press Menu repeatedly to
remove menus.
1
2
3
4
5
Clock Setup
PAGE 24
Press the MENU button and then use the D / E ADJ button
to highlight the Setup menu.
Press the OK (Enter) button to highlight Time.
Press the OK (Enter) button to highlight Clock. Manual or
Auto will appear on the menu next to clock. If manual is
selected, on the menu use the Down arrow to highlight
Manual and press the OK (Enter) button.
Use the ADJ Left/Right arrows to choose the menu options
and the Up/Down arrows to set the options.
When finished setting the clock, press Menu repeatedly to
remove the menus.
On-Off Timers Setup
Set the On-Off Timers using the procedures described above.
*Note: If you intend to use the On-Off Timers, it is best to set the
clock manually.
3
4
5
2
1
- Use the
D / E /
F / GADJ buttons to set the year, month, day, hours
and minutes.
Setup
Setup
--:-- --
--:-- --
--. -- ----
--. -- ----
Clock Manual G
Manual Clock
Daylight Saving
Time Zone
On Timer
Off Timer
Auto Off On
Setup
--:-- --
--. -- ----
Clock Manual G
Manual Clock
Daylight Saving
Time Zone
On Timer
Off Timer
Auto Off
Clock
Manual Clock
Daylight Saving
Time Zone
On Timer
Off Timer
Auto Off
Auto
Manual
Setup
Yr. Mon.
Hr. Min.
Day
Adjust Move Back
--:-- --
--. -- ----
Clock
2006 9 11
PM 11 20
Manual Clock
Daylight Saving
Time Zone
On Timer
Off Timer
Auto Off
On
Setup
Time
G
V-Chip
PC
Menu Language English
Transparent
96
Menu Transparency
Set ID
--:-- --
--. -- ----
Manual Time Settings
Clock Setup (Continued)
PAGE 25
Press the MENU button and then use the D / E ADJ button
to highlight the Setup menu.
Press the OK (Enter) button to highlight Time.
Press the OK (Enter) button to highlight Clock. Manual or
Auto will appear on the menu next to clock. Select Auto
on the submenu with the Down arrow and press the OK
(Enter) button.
Use the ADJ Up/Down/Left/Right arrows to set the
Daylight Savings and Time Zone options for your local
area. See the next page.
When finished setting the clock, press Menu repeatedly to
remove the menus.
3
4
5
2
1
- If you select auto time setting, time will be set from the digital
broadcast information.
Mini glossary
TIME A four-digit figure broken down into hours and minutes, used to enter the current time when setting the clock or wake-up alarm.
HOURS First two digits that are entered when setting the clock or the wake-up alarm.
MINUTES The last two digits that are entered when setting the clock, or the wake-up alarm.
Setup
Setup
Time
G
V-Chip
PC
Menu Language English
Transparent
96
Menu Transparency
Set ID
--:-- --
--. -- ----
Setup
--:-- --
--:-- --
--. -- ----
--. -- ----
Clock Auto G
Manual Clock
Daylight Saving Yes
Time Zone Pacific
On Timer
Off Timer
Auto Off
Auto Off
On
Clock
Manual Clock
Daylight Saving
Time Zone
On Timer
Off Timer
Auto
Manual
Automatic Time Settings
Caution: Some digital channels may change the time incorrectly
using the Automatic Clock Set feature.
In this event, the Alarm may not function as intended and the
TV may not turn on at the expected time.
If the end user will have access to the Alarm, it may be best to
use the Manual Clock Set mode and set the clock to local time
manually.
Clock Setup (Continued)
PAGE 26
Press the MENU button and then use the D / E ADJ button
to highlight the Setup menu.
Press the OK (Enter) button to highlight Time.
Press the OK (Enter) button to highlight Clock. Manual or
Auto will appear on the menu next to clock. Select Auto
on the submenu with the Down arrow and press the OK
(Enter) button.
Use the ADJ Up/Down/Left/Right arrows to highlight and
set the Daylight Savings options: On=Yes or Off=No for
your local area.
When finished, press Menu repeatedly to remove the
menus.
1
2
3
4
5
Installer can elect to use Daylight Savings to adjust the clock time.
This is operated from the Automatic Time Settings.
Installer can set the Time Zone.
Daylight Saving
Time Zone Settings
1
2
Press the MENU button and then use the D / E ADJ button
to highlight the Setup menu.
Press the OK (Enter) button to highlight Time.
Press the OK (Enter) button to highlight Clock. Manual or
Auto will appear on the menu next to clock. Select Auto
on the submenu with the Down arrow and press the OK
(Enter) button.
Use the ADJ Up/Down/Left/Right arrows to highlight and
set the Time Zone for your local area.
When finished, press Menu repeatedly to remove the
menus.
3
4
5
Setup
Time
G
V-Chip
PC
Menu Language
Menu Transparency
Set ID
11:20 PM
Sep.11, 2006
Setup
11:20 PM
Sep.11, 2006
Clock
Manual Clock
Daylight Saving
Time Zone
On Timer
Off Timer
Auto Off
No
Yes
Setup
Select Back
11:20 PM
Sep.11, 2006
Clock
Manual Clock
Daylight Saving
Time Zone
On Timer
Off Timer
Auto Off
Pacific
Setup
Time
G
V-Chip
PC
Menu Language English
Transparent
96
Menu Transparency
Set ID
11:20 PM
Sep.11, 2006
English
Transparent
96
Menu Language
PAGE 27
Press the MENU button and then use the D / E ADJ button
to highlight the Setup menu.
Press the OK (Enter) button.
Use the Down ADJ arrow to highlight Menu Language and
press the OK (Enter) button.
Use the ADJ Up/Down/Left/Right arrows to highlight and
set the Menu Language: English, Spanish or French.
Press the MENU repeatedly to remove the menus.
1
2
3
Choose a language for the on-screen menus.
4
5
Setup
Time
V-Chip
PC
Menu Language English
G
Menu Transparency
Set ID
11:20 PM
Sep.11, 2006
Setup
11:20 PM
Sep.11, 2006
Time
V-Chip
PC
Menu Language
Menu Transparency
Set ID
English
Español
Français
Setup
Time
G
V-Chip
PC
Menu Language English
Transparent
96
Transparent
96
Menu Transparency
Set ID
11:20 PM
Sep.11, 2006
V-Chip
PAGE 28
Press the MENU button and then use the D / E ADJ button
to highlight the Setup menu.
Press the OK (Enter) button.
Use the Down ADJ arrow to highlight V-Chip and press the
OK (Enter) button.
If a password has been entered, key it in using the
number keypad. If no password has been set, enter a
4-digit password (0~9) using the remote control. This is
the PIN. Each time the menu is entered, the password will
be required until the block time expires. The TV is set up
with the default password “0-0-0-0”.
Press the MENU button several times to remove the
menus.
1
2
3
4
5
Entering a PIN (Password)
-This option sets up or changes the password for blocking program ratings.
Setup
Time
G
V-Chip
PC
Menu Language English
Transparent
96
Menu Transparency
Set ID
11:20 PM
Sep.11, 2006
Setup
Enter your PIN.
----
0 9
Menu
BackNumber~
Time
V-Chip
PC
Menu Language
Menu Transparency
Set ID
11:20 PM
Sep.11, 2006
Setup
Changing PIN
G
On/Off Off
TVPG Rating
MPAA Rating
Can. English Rating
Can. French Rating
11:20 PM
Sep.11, 2006
Setup
New PIN
Confirm PIN
----
----
0 9
Menu
BackNumber~
Changing PIN
On/Off
TVPG Rating
MPAA Rating
Can. English Rating
Can. French Rating
11:20 PM
Sep.11, 2006
Setup
Changing PIN
On/Off
TVPG Rating
MPAA Rating
Can. English Rating
Can. French Rating
11:20 PM
Sep.11, 2006
Off
On
If you ever forget your password, key in ‘7’, ‘7’, ‘7’, ‘7’ on the
remote control.
V-Chip (Continued)
PAGE 29
Press the MENU button and then use the D / E ADJ button
to highlight the Setup menu.
Press the OK (Enter) button.
Use the Down ADJ arrow to highlight V-Chip and press the
OK (Enter) button.
Use the Up/Down/Left/Right arrows buttons to choose
and set up the menu options for TVPG Rating.
Press the MENU button several times to remove the
menus.
1
2
3
4
5
TVPG Ratings
-You can block programs based on the TV program rating.
Description of the TV (FCC) Rating Codes:
TV (FCC) Age Categories
TV-MA
Mature audiences only. This program may contain mature themes, profane
language, graphic violence and explicit sexual content.
TV-14
Parents strongly cautioned. This program may contain sophisticated themes,
sexual content, strong language and more intense violence.
TV-PG
Parental guidance suggested. The program may contain infrequent coarse
language, limited violence, some suggestive sexual dialog and situations.
TV-G
General audience. This contains little or no violence, no strong language,
and little or no sexual dialog or situations.
TV-Y7
Directed for older children. Themes and elements in this program may
include mild physical or comedic violence, or may frighten children under
the age of seven.
TV-Y
All children. The themes and elements in this program are specifically
designed for a very young audience, including children from ages two – six.
TV (FCC) Content Sub-Categories:
V Violence.
S Sexual content.
L Offensive language.
D Dialog...sexual innuendo.
FV Fantasy or cartoon violence.
Setup
Time
G
V-Chip
PC
Menu Language English
Transparent
96
Menu Transparency
Set ID
11:20 PM
Sep.11, 2006
Setup
Enter your PIN.
----
0 9
Menu
BackNumber~
Time
V-Chip
PC
Menu Language
Menu Transparency
Set ID
11:20 PM
Sep.11, 2006
Setup
Changing PIN
G
On/Off Off
TVPG Rating
MPAA Rating
Can. English Rating
Can. French Rating
11:20 PM
Sep.11, 2006
Setup
Move
Select
OK
Menu
Back
Allow All Block All
TV
TV-Y
TV-Y7
TV-G
TV-PG
TV-14
TV-MA
FV D L S V
Changing PIN
On/Off
TVPG Rating
MPAA Rating
Can. English Rating
Can. French Rating
11:20 PM
Sep.11, 2006
V-Chip (Continued)
PAGE 30
Press the MENU button and then use the D / E ADJ button
to highlight the Setup menu.
Press the OK (Enter) button.
Use the Down ADJ arrow to highlight V-Chip and press the
OK (Enter) button.
Use the Up/Down/Left/Right arrows buttons to choose
and set up the menu options for MPAA Rating.
Press the MENU button several times to remove the
menus.
1
2
3
4
5
MPAA Ratings
-Restricting movies by their rating.
Description of the MPAA and TV (FCC) Rating Codes:
The MPAA Rating System (Movies)
G General Audience. No restrictions.
PG Children under 13 should be accompanied by an adult.
PG-13 Parental guidance suggested. Children under 13 should be
accompanied by an adult.
R Restricted. Viewers should be 17 or older.
NC-17 Not classified. Viewers should be 17 or older.
X Adults only.
• MPAA ratings: The selected rating will be locked. In addition,
any ratings
that are more restrictive will also be blocked.
Setup
Time
G
V-Chip
PC
Menu Language English
Transparent
96
Menu Transparency
Set ID
11:20 PM
Sep.11, 2006
Setup
Enter your PIN.
----
0 9
Menu
BackNumber~
Time
V-Chip
PC
Menu Language
Menu Transparency
Set ID
11:20 PM
Sep.11, 2006
Setup
Changing PIN
G
On/Off Off
TVPG Rating
MPAA Rating
Can. English Rating
Can. French Rating
11:20 PM
Sep.11, 2006
Setup
Move
Select
OK
Menu
Back
Allow All Block All
PG
G
PG13
R
NC17
X
NR
Changing PIN
On/Off
TVPG Rating
MPAA Rating
Can. English Rating
Can. French Rating
11:20 PM
Sep.11, 2006
V-Chip (Continued)
PAGE 31
Press the MENU button and then use the D / E ADJ button
to highlight the Setup menu.
Press the OK (Enter) button.
Use the Down ADJ arrow to highlight V-Chip and press the
OK (Enter) button.
Use the Up/Down/Left/Right arrows buttons to choose
and set up the menu options for Canadian English Rating.
Press the MENU button several times to remove the
menus.
1
2
3
4
5
Canadian English Ratings
Canadian English Ratings
E Expect No restriction.
C Children
C8+ Viewers should be 8 or older.
G General Audience.
PG Parental guidance suggested. Children under 14 should be
accompanied by an adult.
14+ Restricted. Viewers should be 14 or older.
18+ Restricted. Viewers should be 18 or older.
Press the MENU button and then use the D / E ADJ button
to highlight the Setup menu.
Press the OK (Enter) button.
Use the Down ADJ arrow to highlight V-Chip and press the
OK (Enter) button.
Use the Up/Down/Left/Right arrows buttons to choose
and set up the menu options for Canadian French Rating.
Press the MENU button several times to remove the
menus.
1
2
3
4
5
Canadian French Ratings
Canadian French Ratings
E Expect No restriction.
G For all
8+ Restricted. Viewers should be 8 or older.
13+ Restricted. Viewers should be 13 or older.
16+ Restricted. Viewers should be 16 or older.
18+ Restricted. Viewers should be 18 or older.
Setup
Time
G
V-Chip
PC
Menu Language English
Transparent
96
Menu Transparency
Set ID
11:20 PM
Sep.11, 2006
Setup
Enter your PIN.
----
0 9
Menu
BackNumber~
Time
V-Chip
PC
Menu Language
Menu Transparency
Set ID
11:20 PM
Sep.11, 2006
Setup
Changing PIN
G
On/Off Off
TVPG Rating
MPAA Rating
Can. English Rating
Can. French Rating
11:20 PM
Sep.11, 2006
Setup
Move
Select
OK
Menu
Back
Allow All Block All
C
E
C8
+
G
PG
14
+
18
+
Changing PIN
On/Off
TVPG Rating
MPAA Rating
Can. English Rating
Can. French Rating
11:20 PM
Sep.11, 2006
Setup
Move
Select
OK
Menu
Back
Allow All Block All
G
E
8 ans
+
13 ans
+
16 ans
+
18 ans
+
Changing PIN
On/Off
TVPG Rating
MPAA Rating
Can. English Rating
Can. French Rating
11:20 PM
Sep.11, 2006
Caption Menu
PAGE 32
Press the MENU button and then use the D / E ADJ button
to highlight the Caption menu.
Press the OK (Enter) button.
Use the Down ADJ arrow to highlight On or Off and press
the OK (Enter) button.
Press the MENU button several times to remove the
menus.
1
2
3
4
Turn Captions On/Off
Press the MENU button and then use the D / E ADJ button
to highlight the Caption menu.
Press the OK (Enter) button.
Use the Down ADJ arrow to highlight Analog Mode and
press the OK (Enter) button.
Use the DD / EE / FF / GG ADJ buttons to choose CC1~TEXT4.
Press the OK (Enter) button.
Press the MENU button several times to remove the
menus.
1
2
3
4
5
6
Analog Mode
- Analog Captions will display on the screen whether the signal is
from an RF channel or external equipment input.
*Note: Pressing CC on the remote selects a captions option.
Mini glossary
CAPTIONS The term for the words that scroll across the bottom of the TV screen; usually the audio portion of the program provided for the
hearing impaired.
TEXT The term for the words that appear in a large black frame and almost cover the entire screen; usually messages provided by the
broadcaster.
Caption
On/Off
On G
Analog Mode CC1
Service1
Digital Mode
Digital Font Option
11:20 PM
Sep.11, 2006
Caption
On/Off
On G
Analog Mode
Digital Mode
Digital Font Option
11:20 PM
Sep.11, 2006
Caption
11:20 PM
Sep.11, 2006
On/Off
Analog Mode
Digital Mode
Digital Font Option
Off
On
Caption
11:20 PM
Sep.11, 2006
On/Off
Analog Mode
Digital Mode
Digital Font Option
CC1
CC2
CC3
CC4
TEXT1
TEXT2
TEXT3
TEXT4
*Note: Pressing CC on the remote to select a captions option will also turn
closed captions on.
Caption Menu (Continued)
PAGE 33
Press the MENU button and then use the D / E ADJ button
to highlight the Caption menu.
Press the OK (Enter) button.
Use the Down ADJ arrow to highlight Digital Mode and
press the OK (Enter) button.
Use the DD / EE / FF / GG ADJ buttons to choose Service
1~Service 6.
Press the OK (Enter) button.
Press the MENU button several times to remove the
menus.
1
2
3
4
5
6
Digital Captions Mode
Press the MENU button and then use theD / E ADJ button
to highlight the Caption menu.
Press the OK (Enter) button.
Use the Down ADJ arrow to highlight Digital Font Options
and press the OK (Enter) button.
Use the DD / EE / FF / GG ADJ buttons to customize each
option: Font Size, Font Style, Foreground Color etc.
When finished, press the MENU button several times to
remove the menus.
*Note: If the digital options custom settings are to be cloned, all
menu options should be set to any option other than Default. If
Default is left set for any one option, then all the options will be
reset to default after cloning.
1
2
3
4
5
Digital Font Options
- Digital Captions only appear on digital channels, tune in a digital
channel that is actually broadcasting digital captions.
*Note: Pressing CC on the remote selects a captions option.
Caption
On/Off
On G
Analog Mode
Digital Mode
Digital Font Option
11:20 PM
Sep.11, 2006
Caption
On/Off
On
G
Analog Mode
Digital Mode
Digital Font Option
11:20 PM
Sep.11, 2006
Caption
Font Size Default
G
Font Style
Foreground Color
Background Color
Edge Color
Foreground Opacity
Background Opacity
Edge Style
Default
Default
Default
Default
Translucent
Default
Default
11:20 PM
Sep.11, 2006
Caption
11:20 PM
Sep.11, 2006
On/Off
Analog Mode
Digital Mode
Digital Font Option
Service1
Service2
Service3
Service4
Service5
Service6
Sound Menu
PAGE 34
Press the MENU button and then use the D / E ADJ button
to highlight the Sound menu.
Press the OK (Enter) button.
Use the Up/Down arrow button to highlight Digital
Output, press the OK (Enter) button.
Use the FF / GG ADJ buttons to choose Dolby Digital or PCM.
When finished, press the MENU button several times to
remove the menus.
1
2
3
4
5
-Set the digital audio output as Dolby Digital or PCM.
Digital Audio Output Settings
1
2
3
4
5
- Match the sound mode to the program’s character, Music, Movie
Sports, or News.
Press the MENU button and then use the D / E ADJ button
to highlight the Sound menu.
Press the OK (Enter) button.
With Mode highlighted, press the OK (Enter) button.
Use the DD / EE / FF / GG ADJ buttons to customize each
option: or choose a preset mode like Music, Movie, etc.
When finished, press the MENU button several times to
remove the menus.
Sound Balance Setup
Sound Mode Setup
3
4
5
Press the MENU button and then use the D / E ADJ button
to highlight the Sound menu.
Press the OK (Enter) button.
Use the Up/Down arrow button to highlight Balance, press
the OK (Enter) button.
Use the FF / GG ADJ buttons to move the sound more to the
Left or Right.
When finished, press the MENU button several times to
remove the menus.
1
2
- Adjust the speaker balance for optimum sound quality.
Set up the audio options for the end user
<Dolby Digital>
This product is under license of Dolby Laboratories.
The “Dolby” or D symbol is a trademark of Dolby Laboratories.
Sound
Mode Standard G
Balance
Digital Output
PCM
On
Auto Volume
Multi-Track English
Internal Speaker
On
11:20 PM
Sep.11, 2006
Sound
Mode Standard
Balance
G
Digital Output
PCM
On
Auto Volume
Multi-Track English
Internal Speaker
On
11:20 PM
Sep.11, 2006
Sound
Mode Standard
Balance
Digital Output
PCM
G
On
Auto Volume
Multi-Track English
Internal Speaker
On
11:20 PM
Sep.11, 2006
Sound Menu (Continued)
PAGE 35
Press the MENU button and then use the D / E ADJ button
to highlight the Sound menu.
Press the OK (Enter) button.
Use the Up/Down arrow button to highlight Auto Volume,
press the OK (Enter) button.
Use the FF / GG ADJ buttons to choose On or Off.
Press the MENU button several times to remove the
menus.
1
2
3
4
5
Automatic Volume Control Settings
Press the MENU button and then use the D / E ADJ button
to highlight the Sound menu.
Press the OK (Enter) button.
Use the Up/Down arrow button to highlight Multi-Track,
press the OK (Enter) button.
Use the FF / GG ADJ buttons to choose English, Spanish or
French press the OK (Enter) button.
Press the MENU button several times to remove the
menus.
1
2
3
4
5
- You can set digital audio language.
Digital Audio Language Settings
Press the MENU button and then use the D / E ADJ button
to highlight the Sound menu.
Press the OK (Enter) button.
Use the Up/Down arrow button to highlight Internal
Speaker, press the OK (Enter) button.
Use the
FF / GG
ADJ buttons to choose English, On or Off
press the OK (Enter) button.
Press the MENU button several times to remove the
menus.
1
2
3
4
5
- Set the internal speaker to Off to listen to the TV through an
external audio system, the TV sound will not be heard.
Using External Speakers
Sound
Mode Standard
Balance
Digital Output
PCM
On
G
Auto Volume
Multi-Track English
Internal Speaker
On
11:20 PM
Sep.11, 2006
Sound
Mode Standard
Balance
Digital Output
PCM
On
Auto Volume
Multi-Track
English
G
Internal Speaker
On
11:20 PM
Sep.11, 2006
Sound
Mode Standard
Balance
Digital Output
PCM
On
Auto Volume
Multi-Track English
Internal Speaker
On G
11:20 PM
Sep.11, 2006
- Have the TV automatically maintain the sound level between different channels.
Picture Menu
PAGE 36
To make custom picture settings, set the Mode to Manual on the menu.
Press the MENU button and then use the D / E ADJ button
to highlight the Picture menu.
Press the OK (Enter) button.
Use the Up/Down arrow button to highlight Mode, press
the OK (Enter) button.
Use the FF / GG ADJ buttons to choose a preset picture
setup. When finished, press the OK (Enter) button.
Press the MENU button several times to remove the
menus.
1
2
3
4
5
- Set the picture mode to the program content, e.g. Dynamic or Mild etc.
Picture Mode Setup
Press the MENU button and then use the D / E ADJ button
to highlight the Picture menu.
Press the OK (Enter) button.
Use the Up/Down arrow button to highlight Mode, press
the OK (Enter) button.
Use the FF / GG ADJ buttons to choose Manual and use
Up/Down/Left/Right arrow buttons to set your own
settings for the options. When finished, press the OK
(Enter) button.
Press the MENU button several times to remove the
menus.
1
2
3
4
5
- Use custom settings to watch movies at the best quality.
The user will be able to watch a more realistic picture.
Custom Color Setup
Picture
Mode G
Color Temperature
Normal
16:9
Screen Format
Noise Reduction
Film Mode
11:20 PM
Sep.11, 2006
Picture
Mode
Color Temperature
Standard
G
Contrast 100
Brightness 79
Sharpness 65
Color 70
Tint 0
Screen Format
Noise Reduction
Film Mode
11:20 PM
Sep.11, 2006
Picture Menu (Continued)
PAGE 37
The user can watch movies with a more realistic picture on analog
channels.
Press the MENU button and then use the D / E ADJ button
to highlight the Picture menu.
Press the OK (Enter) button.
Use the Up/Down arrow button to choose Film Mode, press
the OK (Enter) button.
Use the
FF / GG ADJ buttons to choose on or off. When
finished, press the OK (Enter) button.
Press the MENU button several times to remove the
menus.
1
2
3
4
5
- Turn Film Mode On to view movies with optimum preset picture
settings.
Film Mode Options
Press the MENU button and then use the D / E ADJ button
to highlight the Picture menu.
Press the OK (Enter) button.
Use the Up/Down arrow button to choose Color
Temperature, press the OK (Enter) button.
Use the FF / GG ADJ buttons to choose Warm, Cool or
Normal. When finished, press the OK (Enter) button.
Press the MENU button several times to remove the
menus.
1
2
3
4
5
Color Temperature Settings
Press the MENU button and then use the D / E ADJ button
to highlight the Picture menu.
Press the OK (Enter) button.
Use the Up/Down arrow button to choose Screen Format,
press the OK (Enter) button.
Use the FF / GG ADJ buttons to choose a preset screen
format: Set By Program, 16:9 or 4:3. When finished, press
the OK (Enter) button.
Press the MENU button several times to remove the
menus.
1
2
3
4
5
- The user can choose preset formats for the picture.
Screen Format Adjustments
Picture
Mode
Color Temperature
Normal
G
16:9
Screen Format
Noise Reduction
Film Mode
11:20 PM
Sep.11, 2006
Picture
Mode
Color Temperature
Normal
16:9
G
Screen Format
Noise Reduction
Film Mode
11:20 PM
Sep.11, 2006
Picture
Mode
Color Temperature
Normal
16:9
Screen Format
Noise Reduction
Film Mode G
11:20 PM
Sep.11, 2006
Installer Overview
PAGE 38
Following is the Commercial Mode Operation Setup.
Operating Installer Menu
To set up the controls for the TV you will need to know how to enter
the L26W56XA Installer menu and make changes to the default values
as required. If necessary, familiarize yourself with the L26W56XA
Installer menu and how to make and save changes in the menu.
Optional Installer Remote
You will need an Installer remote control similar to the one
shown to the right.
The TV’s clonable features need to be set up before 2-5-5 + Menu is done.
This is a critical step.
If the Master TV display panel’s clonable features like: Clock Set, adding channel
icons and channel labels, etc. are not done properly, then the cloned L26W58X TVs
will all have problems. For example, do not do 2-5-5 + Menu more than once or the
TV setup will become corrupted. If you need to start the procedure over, then begin
by setting installer item 117 to 001, and pressing Enter to reset the TV to default
values in the installer menu. You can do 2-5-4 + Menu mode more than once but
this mode is limited to only editing channel icons and channel labels.
Refer to the appropriate section in the Manual for other TV features: Picture, Sound
etc.
LT2002 Clone Programmer
As the cloning procedure is being performed, specific steps need to
be done at the indicated times to achieve the desired result. Be sure to do each
cloning task as indicated. If a procedure or step is left out or not
performed correctly, then the TV
setup will be wrong and cloning may not
work. At each step, pay attention to assure
the TV screen shows the proper message(s)
when cloning. If the message indicated does
not appear, there is a problem with that step
and cloning may not be successful. Cloning is
only possible when the signal source is an
An
alog channel, not a digital channel.
L26W56XX PTC INSTALLER MENU
000 INSTALLER SEQ 000
UPN 000-000-000-000 FPGA 09F1
PTC V1.00.000 CPU V1.01.00
Typical Installer Menu
QuickSet II Programmer
LT2002
¤
Commercial Mode Setup
PAGE 39
This page provides an overview of the TV configuration. See the pages listed below for more
specific, detailed instructions at each step; how to access and use the Installer menu etc.
*Note1: Disconnect all Aux inputs. Under certain conditions, Auto Program
(Channel search) is disabled if there is an Aux input active.
*Note2: Under certain conditions, changes to the input mode of the RGB
inputs will not take effect until the power is cycled (TV is turned Off and On).
To avoid confusion, disconnect all RGB inputs before entering the Installer
menu.
Overview: Commercial Mode Setup Procedure
1.Set Installer Menu Items
(Enter Installer Menu, see page 43 for detailed instructions.)
a. Set Installer menu item 117 FACT DEFAULT, to 001 and press ENTER.
(This clears all installer menu items, custom settings, channel labels/icons
and reloads the factory default settings.)
b. Set Item 003 BAND/AFC.
- Broadcast: set to 000.- HRC: set to 002
- CATV: set to 001. - IRC: set to 003
c. Set item 028 CH OVERIDE to 001. This allows access to Auto Program,
Channel Labels and Channel List options in the Channel Menu.
d. Set other particular installer items that affect your TV programming
network. See pages 43 - 48.
e. After all required installer menu item settings have been adjusted, press
ENTER on the remote to remove Installer Menu.
2.Set Up TV Features
(See Picture, Sound, Setup menus etc. See TV Clonable options list on
page 49.) Installer Note: Some TV features will have to be set up after
running Auto Program. An example is Digital Font options. This feature is
not available until digital channels are found in the channel scan. Set up
Digital Font options after Auto Program finds a digital channel with
digital captions. Do this before running 2-5-5 + Menu.
3.Run Auto Program
(Search for all available channels.) Go to the Channel menu and access
the Auto Program option, follow on-screen instructions.
a. Edit Channel Scan. In the Channel Menu, access the Channel List menu.
• Delete channels per your system requirements: do you want to delete any
free channels so the guest cannot access them?
• Add familiar Channel Icons like ABC, CBS, NBC etc. to the channel
onscreen display. Add identifiable labels for the end user to readily know
what common networks are available. In the Channel menu, select the
Channel Label option, follow instructions on the bottom of the screen.
4. Transfer TV Setup to Controller Box: 2-5-5 + Menu
After the TV channel scan has been edited and channel label icons added,
enter the Installer menu. Once in the Installer menu, press 2-5-5 and MENU
on the remote. This transfers the TV setup to the internal controller box.
*Note: Only do 2-5-5 + MENU once or TV setup may be corrupted.
TV scans available channels and exits menu when transfer to controller is com-
plete.
5. Perform Adding Custom Channel Labels: 2-5-4 + Menu Mode
Enter Installer menu, press 2-5-4 and Menu. Add your own custom labels to
the channel on-screen displays. (See page 50.) To remove menu press MENU.
*Note: 2-5-4 + MENU can be performed more than once.
Verify TV Setup
At this point, verify that the channel lineup, channel icons and custom
labels are correct. Make sure the TV features are set per your requirements.
Set item 028 CH OVERIDE to 000 to lock the channel scan. After the
preceding has been completed, the Master TV setup is ready to be copied to
the LT2002 Clone Programmer, see next page.
L26W56XA Installer Menu
L26W56XA Installer Menu Items
RJP100M Remote Jack Pack TV Setup
• RJP Available? If you will use an RJP100M
in your system, review installer items:
- 004 Start Channel cannot be set to 000.
- Set 040 Auto Camport to 000.
- Set 093 RJP Available to 001.
Custom Channel Label ‘WXYZ’ created in
2-5-4 + Menu Add Channel Label Mode
After TV setup has been verified,
set item 028 Ch Overide back to 000.
L26W56XX PTC INSTALLER MENU
117 FACT DEFAULT 00X
003 BAND/AFC 00X
028 CH.OVERIDE 001
073 CH. NOT AVBLE 001
004 STRT CHANNEL XXX
040 AUTO CAMPORT 000
093 RJP AVAILABLE 001
028 CH. OVERIDE 000
000 INSTALLER SEQ 000
UPN 000-000-000-000 FPGA 09F1
PTC V1.00.000 CPU V1.01.00
WXYZ
DIGITAL 19-3
MONO SAPSTEREO
WXYZ
ANALOG 2
MONO
Cloning Connections/Learning Setup
PAGE 40
Connections for the LT2002 Clone Programmer to Learn the L26W56XA Master TV Setup.
Clone Programmer
Master L26W56XA
*Notes: It is assumed that the L26W56XA is connected to a signal source, the source selected is Antenna (RF) In, the signal is from an
Analog channel, not a digital channel, all equipment is connected to power and turned on and the LT2002 Clone
Programmer main menu (THE CLONE HAS CONTROL OF THE TV) menu is displayed on the TV screen, the clone programmer LED is blinking
the required heart beat pattern, see above and next page.
*Notes: Once the clone is connected, do not touch the unit or otherwise disturb it or the MPI connections. Any disturbance while the
clone is operating may disrupt the master setup transfer or copying etc.
Before you begin cloning...
• The Master L26W56XA should be connected to a good, stable
signal from an over-the-air antenna or cable service Analog
channel and connected to power. (See above.)
• Teaching and Learning is only possible between identical model
devices. (However, the LT2002 Clone programmer can store up
to 3 different ‘master’ setups.)
WARNING: Copying a blank or incorrect memory into a TV, STB or
other device will cause the TV, STB or other device to operate
erratically or become inoperable.
• Use an Installer’s remote to operate Learning and Teaching
menus.
• Make sure that the batteries in the Clone programmer are fresh.
• If batteries are removed, the Clone Clock time will be lost.
• Decide if you want to set the time from the Clone programmer
TV which has the clock set to the current time.
• Setting the time and transferring it to the Clone or other
device is a separate procedure.
• Follow the connection diagram above to connect the Clone to
a Master L26W56XA TV display panel. After learning is
complete, to another identical L26W56XA TV display panel to
“teach” it the master setup.
• After the L26W56XAs setup has been copied to another
identical L26W56XA, that identical unit with the copied setup,
needs to be disconnected from power for about 15 seconds to
activate the newly-copied setup.
• See the Clone Troubleshooting section to resolve problems.
Turn to the next page to continue Cloning Setup.
THE CLONE HAS CONTROL OF THE TV
THE CLONE IS VERSION XX
THE TV IS VERSION XX
THE SW IS REVISION XX
CLONE CLOCK = XX:XX
TV CLOCK = XX:XX
-PRESS ANY KEY TO CONTINUE.
-DISCONNECT CLONE WHEN DONE.
QuickSet II Programmer
LT2002
¤
Ferrite Core
(TDK, ZCAT
2035-0930)
Antenna
or CATV
Warning: Do not use LT2002
if a LodgeNet PPV card is
installed in TV or clone
programmer device will be
damaged.
Clone Programmer Learning Setup
PAGE 41
Learning the Master TV Setup
Instructions for the Clone Programmer to Learn the Master L26W56XA Setup.
Use MPI Cable to Connect LT2002 Clone Programmer to
Master L26W56XA MPI Port
If there is a good connection, “THE CLONE HAS CONTROL OF TV” message
will appear. Press any key on the Installer remote.
Learn Setup from Master L26W56XA
Press 1 to select the “LEARN FROM TV” option, then press ON/OFF,
POWER, or ENTER to go to the Memory Bank Selection Menu. Pick the
Memory ”Bank” you want to store the master L26W56XA’s setup in by
pressing either Channel key repeatedly to choose Memory 1, 2 or 3.
(If you choose a Memory “Bank” that has a master device’s setup
programmed into it, that setup will be overwritten by the new master
L26W56XA’s setup.) Once the Clone memory bank is selected, press
ON/OFF, POWER, or ENTER. The Clone memory bank you have selected
will be shown. Press ON/OFF or POWER to begin copying the master
L26W56XA’s setup.
Set the Clock (Optional)
Set the time on a Master TV’s Clock. (If the time has already been
copied from a TV into the Clone programmer, you can set a master
TV’s clock by copying the time from the Clone programmer.) The
Clone Programmer can copy the current time to both a master TV and
to the Clone’s internal clock; accurate to within one minute. (Another
reason that the Clone programmer should be equipped with fresh,
high-quality alkaline batteries, is for it to keep the time as accurately
as possible.)
Since the Clone Programmer’s time cannot be set directly, the current
time needs to be copied from a Zenith/LG TV equipped with M.P.I.
input capability.
After the time is copied to the Clone programmer, the current time
can then be transferred to another TV. (This can be a master TV, or
another TV which has already had the features set up.)
*Notes: When using the clone programmer for teaching or learning,
be sure that the heartbeat pattern is shown on the LEDs. Both learning and
teaching should take about 45 or more seconds depending on the complexity
of the master setup. While the clone is functioning, do not move it or otherwise
disturb the clone or wiring connections. If the clone finishes the function in less than
45 seconds, redo the function again. Press the reset button if the clone does not act
normally.
LT2002 Clone Programmer Communication Problems
• A slow flashing green light indicates there are communication
problems between the L26W56XA and the LT2002 clone
programmer. If this is the case, check for a damaged cable,
poor contacts, or other connection troubles.
• If the status indicator is red, the programmer batteries are
low and should be replaced. Install 4 high-quality alkaline AA
batteries.
THE CLONE HAS CONTROL OF THE TV
THE CLONE IS VERSION XX
THE TV IS VERSION XX
THE SW IS REVISION XX
CLONE CLOCK= XX:XX
TV CLOCK= XX:XX
-PRESS ANY KEY TO CONTINUE.
-DISCONNECT CLONE WHEN DONE.
This menu should appear by itself after the
LT2002 is connected to the L26W56XA MPI port.
CLONE SELECTION MENU
(1) LEARN FROM TV
(2) TEACH TO TV
(3) SET CLONE CLOCK FROM TV
(4) SET TV CLOCK FROM CLONE
(5) DISPLAY TV SETUP
(6) DISPLAY CLONE SETUP
- TO CHANGE MENU ITEMS, PRESS
CHANNEL KEYS OR DIGITS.
- TO EXECUTE ITEM, PRESS ON/OFF,
POWER, OR ENTER
Cloning Connections / Teaching Setup
PAGE 42
Teaching the Master Setup to Another L26W56XA
Connections for the LT2002 to Teach another L26W56XA the Master Setup
Teach Master L26W56XA’s Setup to the target
L26W56XA
After learning is complete, remove the M.P.I. cable from the
master L26W56XA and connect it to the target L26W56XA that
you want to copy the master L26W56XA’s setup into. With “THE
CLONE HAS CONTROL OF TV” message displayed, press 2 to go to
the “TEACH TO TV” option, press ON/OFF, POWER, or ENTER.
Select the LT2002 memory that the new setup is in. Press
On/Off to transfer the new setup and other information to the
new L26W56XA. Teaching usually takes 2-3 minutes.
After the “TEACHING COMPLETE” message is displayed, press any
key to return to the Clone menu, then press ON/OFF, POWER, or
ENTER. If finished, detach M.P.I. cable from the target, newly
cloned L26W56XA.
Disconnect L26W56XA Power for 15 Seconds
Unplug the AC power cord of the newly cloned L26W56XA from
the power outlet for about 15 seconds to activate the newly-
copied setup.
CLONE SELECTION MENU
(1) LEARN FROM TV
(2) TEACH TO TV
(3) SET CLONE CLOCK FROM TV
(4) SET TV CLOCK FROM CLONE
(5) DISPLAY TV SETUP
(6) DISPLAY CLONE SETUP
- TO CHANGE MENU ITEMS, PRESS
CHANNEL KEYS OR DIGITS.
- TO EXECUTE ITEM, PRESS ON/OFF,
POWER, OR ENTER
TEACHING IN PROGRESS,
PLEASE WAIT
TEACHING COMPLETE
This menu should appear after any key is
pressed on the Installer remote.
This display will appear during Teaching
function.
This display will appear after Teaching is
complete.
QuickSet II Programmer
LT2002
¤
THE CLONE HAS CONTROL OF THE TV
THE CLONE IS VERSION XX
THE TV IS VERSION XX
THE SW IS REVISION XX
CLONE CLOCK = XX:XX
TV CLOCK = XX:XX
-PRESS ANY KEY TO CONTINUE.
-DISCONNECT CLONE WHEN DONE.
Clone Programmer
Master L26W56XA
Ferrite Core
(TDK, ZCAT
2035-0930)
Antenna
or CATV
Installer Menu
PAGE 43
Typical Installer Menu
L26W56XX PTC INSTALLER MENU
000 INSTALLER SEQ 000
UPN 000-000-000-000 FPGA 09F1
PTC V1.00.000 CPU V1.01.00
Use the Installer’s Menu to set up or change operational settings.
See more detailed descriptions of the Installer menu items on the following pages...
Accessing the Installer’s Menu
Make sure TV is on. Installer’s menu items can be accessed by using an installer’s remote
control. Just press MENU repeatedly (at least 10 times) until the TV seems to stop
responding, then press 9, 8, 7, 6, then ENTER to access the Installer’s menu. To remove
the Installer’s menu, press ENTER again. Any changes you make will be stored in non-
volatile memory. (The menu also disappears automatically.)
The Installer’s menu opens with item 000 INSTALLER SEQ 000. Use the Up/Down arrow
keys to sequence through the available menu items. Or, access an item directly by keying
in the line number, then pressing MENU. For example, to access the Sleep Timer option
which is item 015, press 0-1-5, then MENU. To change a setting, use the Left/Right
arrow keys. Or, enter a value directly.
Using the Installer’s Menu
Items 000 ~ 117 are immediately accessible only upon entering the Installer’s Menu.
Their numbers, descriptions, ranges, factory default settings, and a place for listing any
changes made on-site are given below and on the following pages.
Installer Menu Items 000 through 117
Menu Item Function Value Range Default Value Brief Description of Function and Comments
000 INSTALLER SEQ 0 ~ 3 0 Leave default set to 0.
001 POWER MANAGE 0 ~ 7 0 Sets number of hours of no activity before auto shut Off.
002 AC ON 0 / 1 0 Set to 1 to enable auto turn On at power up.
003 BAND/AFC 0 ~ 3 1 Selects Tuning Band: 0=Broadcast, 1=CATV, 2=HRC, 3=IRC
004 STRT CHANNEL 0~125, 126, 127, 255 255 Channel at turn-on (Set 255 to return to last channel before power Off).
005 CHAN LOCK 0 / 1 0 If set to 1, cannot tune from current channel.
007 STRT VOLUME 0 ~ 63, 255 255 Sets Volume level at TV turn-on (Set 255 to retain last volume level).
008 MIN VOLUME 0 ~ 63 0 Sets minimum allowable volume setting.
009 MAX VOLUME 0 ~ 63 63 Sets maximum allowable volume setting.
010 MUTE DISABLE 0 / 1 0 Set to 1 to disable mute function.
011 KEY DEFEAT 0 / 1 0 Set to 1 to disable menu navigation keys on display panel.
015 SLEEP TIMER 0 / 1 1 Set to 1 to enable Sleep Timer.
016 EN TIMER 0 / 1 0 Set to 1 to enable On/Off Timers.
017 ALARM 0 / 1 1 Set to 1 to enable Alarm.
021 V-CHIP 0 / 1 1 Set to 1 to enable V-Chip functions.
022 MAX BLK HRS 0 ~ 99 12 Sets number of V-Chip (Parental Control) blocking hours.
023 CAPTION LOCK 0 / 1 0 Set to 1 to retain caption setting at power Off.
028 CH. OVERIDE 0 / 1 1 If set to 0, limits direct access to favorite channels.
029 OLD OCV 0 / 1 0 Set to 1 to change M.P.I. operation to OCV.
030 ACK MASK 0 / 1 0 If set to 1, changes M.P.I. for some OCV boxes.
031 POLL RATE 20 ~ 169 94 Selects poll rate for M.P.I.
032 TIMING PULSE 186 ~ 227 207 Sets baud rate for M.P.I.
034 CAMPORT EN 0 / 1 1 Set to 1 to enable Video 2 input.
*Notes:
For operation with RJP100M, set item 040
AUTO CAMPORT to 000. Set item 093 RJP AVAILABLE to
001. Installer menu items 004, 040, 093, affect
RJP100M operation.
Installer Menu
PAGE 44
Menu Item Function Value Range Default Value Brief Description of Function and Comments
035 COMPPORT EN. 0 / 1 1 Set to 1 to enable HDMI. Set to 0 to disable.
038 YPrPb EN. 0 / 1 1 Set to 1 to enable display panel Component 1 input jacks.
039 REAR AUX EN 0 / 1 1 Set to 1 to enable display panel Video 1 input jack.
040 AUTO CAMPORT 0 / 1 1 Set to 1 to automatically switch to Camport.
046 STRT AUX SRCE 1 ~ 7, 255 255 Sets the starting AUX source.
047 AUX STATUS 0 / 1 0 Set to 1 for M.P.I. AUX source to be reported as a channel number instead of Channel 0.
053 DIS. CH-TIME 0 / 1 0 Set to 1 to disable Channel-Time display.
069 EN. CH-T COL. 0 / 1 1 Set to 1 to enable custom color for the Channel-Time display.
070 FOR. CH-TIME 0 ~ 7 2 Chooses custom foreground color for the Channel-Time display.
071 BCK. CH-TIME 0 ~ 7 2 Chooses custom background color for the Channel-Time display.
073 CH NOT AVBLE 0 / 1 0 If set to 1 and channel override is 0, “NOT AVAILABLE” message is displayed
when directly accessing a channel not in the favorite channel list.
075 REVERT CH 0 / 1 0 If set to 1 and loss of M.P.I. communication occurs, TV tunes to Start Channel.
078 UPN MSB 0 ~ 255 0 User programmable number, most significant byte.
079 UPN MSB-1 0 ~ 255 0 User programmable number, most significant byte - 1.
080 UPN MSB-2 0 ~ 255 0 User programmable number, most significant byte - 2.
081 UPN LSB 0 ~ 255 0 User programmable number, least significant byte.
082 CHKSM ERROR 0 / 1 1 Enforces rigid M.P.I. checksum.
083 HANDSHK TIME 0 ~ 5 5 Relaxes M.P.I. timing to be compatible with PC based Windows-controlled systems.
084 PERMANENT BLK 0 / 1 0 Removes block hours setting for Parental Control and makes block permanent.
087 REAR RGB EN. 0 / 1 1 Enables RGB1 input. Set to 1 to enable, set to 0 to disable.
088 EN NOISE MUTE 0 / 1 1 If set to 1, mutes audio if no signal is present.
090 KEY LOCK 0 / 1 0 If set to 1, keyboard is locked out, IR is still functional.
091 YPrPb2 EN. 0 / 1 1 Set to 1 to enable Component 2 input jacks.
092 RGB2 ENABLE 0 ~ 2 2 Enables Video 3 input. Set to 1 for Composite Video or 2 for S-Video. Set to 0 to disable.
093 RJP AVAILABLE 0 / 1 0 Set to 1 to enable.
094 SAP MENU EN 0 / 1 1 Set to 0 to disable feature on Function menu. Set to 1 to enable feature on Function menu.
096 DEF. ASP. RATIO 0, 1, 2, 4, 5 2 Sets default aspect ratio at power up. See detailed descriptions and item 106.
102 ATSC BAND 0 ~ 4 4 Selects ATSC band.
103 ATSC TUNE MODE 0 / 1 1 Sets ATSC tuning mode. Set to 0 for virtual channels, set to 1 for physical channels.
104 START MINOR CH 0 ~ 255 0 Selects Minor start channel. Set 0 for NTSC. Not 0, sets Minor channel number.
106 ASP RATIO LOCK 0 / 1 0 To retain set aspect ratio on power cycle, set to 1. Set to 0 for default ratio on power cycle.
107 BANNER SELECT N/A N/A Not applicable.
116 VIDEO MUTE EN 0 / 1 0 Set to 0 for normal, set to 1 for Blank.
117 FACT DEFAULT 0 / 1 0 0=Normal. 1=Loads factory default presets of all above settings.
Installer Menu Items 035 through 117
Installer Menu
PAGE 45
Detailed Descriptions of Installer Menu Items
000 - INSTALLER SEQUENCE
Specifies entry sequence to the Installer Menu.
0 = 9876 1 = 4321
2 = 1478 3 = 3698
001 - POWER MANAGE (Power Management)
Determines hours of no activity before automatic shutoff. The
POWER MANAGE function is for saving energy. If set to 0, Power
Manage is Off. Settings range from 0 ~ 7, with 1 ~ 7 representing
the hours that the TV will remain On, unless there has been activity
from either the control panel or remote control.
002 - AC ON (AC Power Switchable)
If set to 1, allows the L26W56XA to turn On just by applying AC
power. Pressing the On button is not necessary. This is desirable if
the L26W56XA is plugged into a cable box or a power outlet
controlled by a wall switch. Use ADJ Left/Right arrow to choose 0 or
1 where 0 is the default is Off, and 1 is On.
*Note: If set to 1 (On), the L26W56XA does not respond to On/Off
commands from either the remote or the display control panel, and
the SLEEP TIMER is also nonfunctional.
003 - BAND/AFC (Band/Automatic Frequency Control)
Selects the tuning band. There are 4 possible settings for this
option:
0 = Broadcast 1 = CATV
2 = HRC 3 = IRC
If some channels were not found by Auto Program, select the
appropriate Band setting here and add the channels using the
Channel List option in the Channel Menu.
004 - STRT CHANNEL (Start Channel)
If active, this function allows you to determine the initial channel
number when the L26W56XA is turned On. This feature is useful for
an in-house information channel, since the L26W56XA would always
select that channel when it is turned On. Setting this to 255 causes
the last channel viewed when the L26W56XA was turned Off, to be
the tuned to channel when the L26W56XA is turned On again.
255 = Last channel 1 ~ 125 = Ch X 0 = Aux
126 Map to Channel 3. 127 Map to Channel 4.
*Note: Item 004 STRT CHANNEL cannot be set to 0 if item 093 RJP
AVAILABLE is set to “1”.
005 - CHAN LOCK (Channel Lock)
CHAN LOCK is ideal if the system must always be on the same
channel. Changing channels with Channel Up/Down or keypad
numbers is impossible. Channel Lock is inactive if set to 0 (default).
Generally, this feature is used in connection with START CHANNEL
(Installer item 004) where the start channel may, for example, be
set to 3 or 4. If the start channel is 3, then the L26W56XA will
remain locked on Channel 3.
007 - STRT VOLUME (Start Volume)
This function allows the Installer to determine the initial volume
level setting when the L26W56XA is turned On. This feature is useful
for an in-house information channel, since the L26W56XA would
always select that volume level when it is turned On. The range of
values are 0 - 63, 255. If 255 is selected, the current volume level
will be retained in memory when the L26W56XA is turned Off; at
turn On, the volume level will be automatically set at the previous
or last level.
008 - MIN VOLUME (Minimum Volume)
This function determines the minimum volume level allowable with
the VOLUME (VOL) Up/Down control. In this way, for example,
someone cannot set the volume too low to hear. The value range is
from 0 to 63 — change values with ADJ Left/Right arrow. The
factory default is 0, which provides the full range of volume control,
if item 009 MAX VOLUME is also set to 63. It may be best to set the
same value on every L26W56XA.
*Note: The minimum volume level cannot have a value setting higher
than the MAX VOLUME level (described below).
009 - MAX VOLUME (Maximum Volume)
This function determines the maximum volume level allowable with
the VOLUME (VOL) Up/Down controls. In this way, for example,
someone can not set the volume level high enough to disturb
others.
(Continued on next page)
*Note: For Items 007, 008 and 009
For legacy reasons, the scale used is 0 - 63. The PTC software will
translate this to the 0 - 100 scale used by the TV.
To translate a TV volume level to the installer menu value, use the
following formula:
Installer Value = TV V
alue x 63
100
Enter only the whole number (disregard fractions).
Installer Menu
PAGE 46
The value range is 0 to 63, with 63 as the default, which gives the
user the full range of volume control, if item 008 MIN VOLUME is
also set at 0. Change values with ADJ Left/Right arrow keys. It may
be best to set the same value on every L26W56XA.
*Note: The maximum volume level cannot have a value setting lower
than the MIN VOLUME level (described previously).
010 - MUTE DISABLE
Enables or disables sound mute function. If set to 1, sound cannot
be muted, mute is disabled. If set to 0, sound can be muted.
011 - KEY DEFEAT (Keyboard Defeat)
If set to 1, key defeat prevents the end user from accessing the on-
screen menus with the display front panel—MENU, SELECT, and Left /
Right arrow keys and TV/AV do not function. If set to 0, those keys
do function.
*Note: The menus can always be accessed by pressing MENU on the
remote.
015 - SLEEP TIMER
If set to 1, the SLEEP TIMER feature may be used. If set to 0, the
Sleep Timer is not available.
016 - EN TIMER (Enable On/Off Timers)
If set to 1, Timer function is available to user. Set to 0 to disable
On/Off Timer functions. (Clock must be set in order to use Timers.)
017 - ALARM
Gives the installer the option of making the Alarm function available
to the end user. If set to 1, Alarm function is available to end user.
Set to 0 to disable the Alarm function.
*Note: Clock must be set before the Alarm function will work.
021 - V-CHIP (Parental Control)
Set to 1 to activate V-Chip (Parental Control); have it available to
end user to filter and control or otherwise restrict programming
content that can appear. Set to 0 to turn V-Chip feature Off, not
available to user; no programming restrictions can be set.
022 - MAX BLK HRS (Maximum Block Hours)
Sets hours from 0 to 99 for the maximum V-Chip (Parental Control)
block hours. Default setting is for 12 blocking hours.
023 - CAPTION LOCK
Set to 1 to restore previous caption On/Off state after turn Off. If set
to 0, captions are always Off at turn On.
028 - CH. OVERIDE (Channel Override)
If set to 1, the user can select channels with either Channel
up/down or by direct keypad entry. If set to 0, only those channels
that are added on the channel list can be selected.
029 - OLD OCV (On Command Video
TM
)
Set to 1 for operation with systems from On Command Corporation.
030 - ACK MASK
M.P.I. Communication Parameter. Leave at default setting unless
changed by Pay-Per-View provider. When set to 1, changes M.P.I. for
some OCV boxes.
031 - POLL RATE
M.P.I. Communication Parameter. Selects Poll Rate for M.P.I. Leave at
default setting unless changed by Pay-Per-View provider. Step size of
16 ms.
032 - TIMING PULSE
M.P.I. Communication Parameter. Leave at default setting unless
changed by Pay-Per-View provider. Sets baud rate. Step size of 4.3
uS.
034 - CAMPORT EN. (Camera Port Enable)
Set to 1 to enable Video 2 input on display panel. If set to 0, Video
2 input on display panel is not functional.
035 - COMPPORT EN. (Computer Port Enable)
Enable/disables display panel HDMI input jack. Set to 0 to disable,
set to 1 to enable.
*Note: The setting above is ignored if Installer item 093 RJP
AVAIL ABLE, is set to 1.
038 - YPrPb EN. (Rear Component Video Enable)
Set to 1 to enable display panel rear Component Video 1 input.
Set to 0 to disable display panel rear Component Video 1 input.
039 - REAR AUX EN. (Rear Aux Enable)
Set to 1 to enable display panel rear AUX (Video 1) input.
Set to 0 to disable display panel rear AUX (Video 1) input.
040 - AUTO CAMPORT
Set to 1 to automatically switch to Camport when equipment is
connected to front Video input.
Set to 0 to disable front Video automatic source selection.
*Note: This item must be set to 0 in order to enable item 093 RJP
AVAILABLE to be set to 1.
046 - STRT AUX SRCE (Start Aux Source)
Sets the starting AUX source.
Start source if start channel =0
1 = Video1 4 = RGB1 7 = Video 3 / S-Video
2 = Video2 5 = Component 2 255 = Last Aux
3 = HDMI 1 6 = Component 1
047 - AUX STATUS
Set to 1 for M.P.I. AUX source to be reported as a channel number
instead of channel 0. Set to 0 to disable AUX identification change.
Controls M.P.I. status channel response for AUX inputs.
(Continued from previous page)
Installer Menu
PAGE 47
053 - DIS. CH-TIME (Disable Channel-Time)
Set to 1 to disable the Channel-Time display, Channel-Time display
will not appear.
Set to 0 to enable the Channel-Time display.
069 - EN. CH-T COL. (Enable Channel-Time Custom Color)
Set to 1 to enable custom color for the Channel-Time display.
Set to 0 to disable custom color for the Channel-Time display.
070 - FOR. CH-TIME (Channel-Time Display Foreground Color)
Set according to Color Chart.
0 = Black 3 = Yellow 6 = Cyan
1 = Red 4 = Blue 7 = White
2 = Green 5 = Violet
*Note: If foreground and background colors are the same, menu
background is transparent.
071 - BCK. CH-TIME (Channel-Time Display Background Color)
Set according to Color Chart.
0 = Black 3 = Yellow 6 = Cyan
1 = Red 4 = Blue 7 = White
2 = Green 5 = Violet
*Note: If foreground and background colors are the same, menu
background is transparent.
073 - CH NOT AVBLE (Channel Not Available)
If set to 1 and item 028 CHANNEL OVERRIDE is set to 0, “NOT
AVAILABLE” message is displayed when directly accessing a channel
not in the channel scan list available in memory.
075 - REVERT CH (Revert to Start Channel)
If set to 1 and loss of M.P.I. communication occurs, TV automatically
tunes to the specified Start Channel.
077 - QUICK SHUTOFF
Allows TV power off to be controlled by the pillow speaker channel
selection button. User would press and hold button down for time
required to have TV turn off. Value Range 0 ~ 17, each number
represents 1/2 second. For example, if set to 4, TV would turn off if
user held speaker channel button down for 2 seconds.
078 - UPN MSB (UPN Most Significant Byte)
User programmable number, most significant byte readable by M.P.I.
command. Note: Not linked to serial number.
079 - UPN MSB-1 (UPN Most Significant Byte-1)
User programmable number, most significant byte-1 readable by
M.P.I. command. Not linked to serial number.
080 - UPN MSB-2 (UPN Most Significant Byte-2)
User programmable number, most significant byte-2 readable by
M.P.I. command. Not linked to serial number.
081 - UPN LSB (UPN Least Significant Byte)
User programmable number, least significant byte readable by M.P.I.
command. Not linked to serial number.
082 - CHKSM ERROR (Checksum Error)
Enforces rigid M.P.I. checksum validation.
Set to 1 for validation.
Set to 0 to disable (does not check checksum on M.P.I. async port).
SPI is always checked.
083 - HANDSHK TIME (Handshake Time)
Adds an additional delay to the handshake time which is 64 msec,
thus relaxing M.P.I. timing requirements to be compatible with PC
based Windows controlled systems, range is 0 - 5.
(Timeout = 25.5MS + [25.5 MS* Handshake time]).
084 - PERMANENT BLK (Permanent Block)
Allows Lock (Parental Control) blocking schemes to be permanent by
disabling the blocking hours function.
Set to 1 to install Parental Control restrictions permanently.
Set to 0 for user-specified hours control of blocking schemes.
087 - REAR RGB EN. (Rear RGB1 Enable)
Controls access to rear RGB1 input on display panel.
Set to 1 to enable RGB1 input for DTV. Set to 0 to disable RGB1
input.
*Note: The setting above is ignored if Installer item 093 RJP
AVAILABLE, is set to 1. Then 087 - REAR RGB EN. above, always
resets itself to PC (1) -- regardless of what value appears for item 087
on the Installer menu.
088 - EN NOISE MUTE (Enable Noise Mute)
If set to 1, audio mutes if no signal is present.
090 - KEY LOCK
If set to 1, display panel keyboard is locked out, not available to end
user. IR receiver remains functional.
091 - YPrPb2 EN. (Rear Component Video 2 Enable)
Set to 1 to enable display panel Component 2 input.
Set to 0 to disable display panel Component 2 input.
092 - RGB2 ENABLE (Red-Green-Blue 2 Enable)
Set to 1 to enable display panel Video 3 input for Composite Video,
set to 2 to enable for S-Video. Set to 0 to disable display panel
Video 3 input.
093 - RJP AVAILABLE
Set to 1, remote jack pack is available.
Set to 0, remote jack pack is not available.
*Note: This item can not be set to 1 if item 040 AUTO CAMPORT is set
to 1.
(Continued on next page)
Detailed Descriptions of Installer Menu Items
Installer Menu
PAGE 48
094 - SAP MENU EN (2nd Audio Program)
Set to 1 to enable SAP feature, if available.
Set to 0 to disable SAP feature.
096 - DEF. ASP. RATIO (Default Aspect Ratio)
Selects default aspect ratio at power up, see settings below.
102 - ATSC BAND
Sets up TV to receive different types of incoming signals:
0=Broadcast, 1=CATV, 2=HRC, 3=IRC, 4=Same as NTSC.
103 - ATSC TUNE MODE
Selects ATSC tuning mode: 0=Virtual, 1=Physical.
Note: The setting above is ignored if Installer item 102 ATSC BAND,
is set to 1=CATV, 2=HRC, or 3=IRC. Then 103 - ATSC TUNE MODE
above always resets itself to Physical (1), regardless of what value
appears for item 103 on the Installer menu.
104 - START MINOR CHANNEL
Sets XX-XX minor starting channel at power up: 0=NTSC. If not 0,
number
selected is the Minor start channel number.
106 - ASP RATIO LOCK (Aspect Ratio Lock)
Set to 1 to retain previous aspect ratio with power Off.
Set to 0 to retain default aspect ratio with power Off. See item 96
Default Aspect Ratio above.
107 - BANNER SELECT
Not applicable.
116 - VIDEO MUTE EN (Video Mute Enable)
Set to 0 for normal.
Set to 1 for blank.
117 - FACT DEFAULT (Factory Default)
Set to 0 for normal.
Set to 1 to load default settings for all installer menu items.
WARNING: Setting this to 1 will reload the factory
defaults and clear the channel list including erasing any
assigned Channel Icons and Labels.
Set to 0 for set by program.
Set to 1 for 4:3.
Set to 2 for 16:9 (Factory Default).
Set to 4 for Zoom 1
Set to 5 for Zoom 2
(Continued from previous page)
PAGE 49
Clonable Menu Features
Channel
Auto Program (Active
channels found with
the channel search)
Channel Labels
Channel List
Fine Tune
Picture
Mode
Contrast
Brightness
Color
Sharpness
Tint
Color Temperature
Screen Format
Film Mode
Sound
Mode
Treble
Bass
Balance
Auto Volume
Multi-Track
Internal Speaker
Setup
Time
Clock
Auto Off
V-Chip
TVPG Rating
MPAA Rating
Menu Language
SET ID
Caption
On/Off
Analog Mode
Digital Mode
Digital Font Option
Reference: TV Features / Menus that can be Cloned
*Note:
For Digital Font Options, if any default setting is left unchanged prior to cloning, then all the digital font options wil be set to default settings. If you
want custom digital font options to be clonable, set all digital font options to settings other than Default.
PAGE 50
Reference: Procedures for adding Channel Label Icons/Custom Channel Labels
(2-5-4 + MENU Mode)
Adding Channel Icons and Labels in the 2-5-4 + Menu Mode
Installer Remote Control Key Functions for Master TV Channel Editing/Labeling Menu
Editing/Adding Channel ICONs and/or Labels
If there is no pre-assigned ICON, you can make a channel label of up
to 7 characters to help in identifying the channel or network.
At your option, channel labels can also be added in addition to a
pre-assigned ICON. You may also add labels for the Aux input sources
to clearly identify the devices that are connected to the Aux inputs.
Editing and adding the labels can only be done if there are
channels entered into the L26W56XA’s channel map either by
using the method described in item 6 (page 51), by cloning or
by the use of the master remote control from the PPV provider.
To Do Channel Editing/Labeling, proceed as follows
1. Enter L26W56XA Installer menu.
2. After the installer menu appears, press ‘2’, ‘5’, ‘4’, ‘MENU’.
This enters the channel label edit mode.
Add your channel icons and channel labels in this menu,
see below. (You can do this more than once.)
3. To exit the menu when done press “MENU”.
• CHANNEL Up/Down - Tunes in the next channel in scan.
• Left/Right Arrows - Select the item to change. If “I” is shown,
the ICON can be changed. If a number is shown, it indicates the
position of the character that can be changed.
• Up/Down Arrows - Select the ICON or the character to be
displayed.
• 0 – 9 - Use to enter the index number of the ICON, if known.
• OK (Enter/Select) - Changes the ICON after the number has been
entered.
• TV/AV - Changes the Aux input label. This key is located on side
of set and on Installer remote control.
• MENU - Exits the labeling/editing menu.
Changing a Channel’s ICON on Master
TV
1. With Channel Up/Down, select the channel
you want to change the Icon for.
2. With the Right or Left ADJ arrow, select
the letter ‘I’ on the channel ID display.
3. With the Up or Down arrow, select the
desired ICON you want to appear to
identify the channel. (If you know the
ICON number, enter the number followed
by Enter / Select.)
Note: If no Icon is available, leave at or
select the default blank icon display.
4. Proceed with Changing/Adding Labels or
go to the next channel.
Changing/Adding Channel Labels on
Master TV
1. Channel Up/Down to select the desired
channel.
2. Press the Right or Left ADJ arrow
repeatedly until the numbers 1 to 7 show
up. The number shows the position of the
character that can be changed. Number 1
is the first character, number 2 the second
character and so on.
3. With the Up or Down arrow, select the
desired character.
4. Proceed to the next number position or
use Channel Up/Down to go to the next
channel.
Changing Source Labels on Master TV
1. Press “TV/AV” to select the desired Aux
input source; Video 1, Component, S-Video
etc.
2. Press the Right or Left arrow repeatedly
until the numbers 0 to 9 show up.
The number shows the position of the
character that can be changed.
3. Use the Up or Down arrows to select the
desired character.
4. Press “TV/AV” for the next Aux source or
proceed with Changing Icon or
Changing/Adding Labels.
1
2
3
4
5
6
7
XYZ
XYZ
XYZ
NETWORK
(Label)
(Icon)
PAGE 51
Reference: Detailed Information For Making A Master TV
IMPORTANT INSTALLER SETUP INFORMATION! PLEASE READ THE FOLLOWING...
To set up a master TV you will need to know how to
enter the L26W56XA Installer menu and make changes to
the default values as required. If necessary, familiarize
yourself with the L26W56XA Installer menu and how to
make and save changes in the menu, bef
ore attempting to clone the
L26W56XA Master TV setup.
You will also need an Installer remote control similar to the one
shown in the front of this manual.
Finally, the TV’s clonable features need to be set up. This is a
critical step. If the Master TV display panel’s clonable features like
adding channel icons or channel labels are not correctly added, then
the cloned L26W56XAs TVs will all have problems.
As the cloning procedure is being performed, specific steps need to
be done at the indicated times to achieve the desired result. Be sure
to do each task as indicated. If a procedure or step is left out or not
performed completely, cloning may not work. At each step, pay
attention to assure the TV screen shows the proper message when
cloning. If the message indicated does not appear, there is a
problem with that step and cloning may not be successful. Cloning
is only possible when the signal source is an An
alog channel, not a
digital channel.
Making a Master TV
Detailed Instructions
The following describes the procedure for preparing a Master
L26W56XA for cloning and the procedure for adding Channel Icons
and/or Labels.
Note 1: Disconnect all Aux inputs. Under certain conditions, Auto
Program Scan is disabled if there is an Aux input active.
Note 2: Under certain conditions, changes to the input mode of the
RGB inputs will not take effect until the power is cycled (TV is
turned Off and On). To avoid confusion, disconnect all RGB inputs
before entering the Installer menu.
1. Enter the L26W56XA installer menu.
a. Reset the internal controller to factory default by accessing
installer menu item 117 FACT DEFAULT, set it to 1 and press
“ENTER”. The value will change back to 0 after the TV’s internal
controller has been restored to factory default condition.
b. Within the Installer menu, set the Installer menu items to the
configuration required of your institution.
c. It is important to set the tuning band at this time, see
Installer menu item 03 BAND/AFC.
d. Set Installer menu item 28 – CH OVERIDE to 001 to allow
access to the Auto Program and Channel List/Channel Label
features in the Channel Menu. Exit the Installer menu.
2. Access the Master TV menus and set the clonable options on the
menus to the desired configuration. Refer to the Clonable Menu
Features Chart on the see page 49.
3. Run Auto Program.
4. Enter the Channel List/Channel Label menu and edit the channel
line-up to include the Free-To-Guest Channels only.
5. Assign ICONs to the channels using the Channel Label Menu.
Note: You can add Channel ICONS typically network logos like
ABC, NBC, PBS etc. in this step. Or, in Step 7, add Channel ICONS
or labels for channels without Icons.
6. Transfer the TV setup: Enter the L26W56XA installer menu.
Press ‘2’, ‘5’, ‘5’, ‘MENU’ to start the transfer of the TV’s setup to
the L26W56XA. Once the transfer is complete, the system will
exit the Installer menu.
Note: Only do 2-5-5 + MENU once. The TV setup may be
corrupted if 255 + Menu is done more than one time.
7. Edit/Add Channel ICONs and Channel Labels as needed.
Enter Installer menu. With menu displayed, press 2-5-4 + MENU.
See page 49 for detailed instructions:
- Editing/Adding Channel ICON and Labels on Master TV
- Changing a Channel’s ICON on Master TV
- Changing/Adding Channel Labels on Master TV
- Changing Source Labels on Master TV
8. Verify Master TV setup and feature configuration:
• Did you add Channel ICONS?
• Did you add Channel Labels?
• Did you add Aux Source Labels?
• Did you adjust all TV menu options as required?
The TV master setup is now ready to be cloned. Go to the master
TV cloning section or continue on to page 49.
PAGE 52
Reference: Software Version Check
Procedure to Check Software Version
The software version of the L26W56XA may be checked by accessing the INSTALLER MENU. To do this, press the MENU button at least 10
times until the menu display ceases to respond to MENU key presses.
Then, press "9", "8", "7", "6", "OK (Enter/Select)".
Typical Installer Menu
L26W56XX PTC INSTALLER MENU
000 INSTALLER SEQ 000
UPN 000-000-000-000 FPGA 09F1
PTC V1.00.000 CPU V1.01.00
PAGE 53
L26W56XA Camport Auto Sense Operation
The CAMPORT Auto Sense function is enabled when:
1. Installer Menu Item 34, CAMPORT EN is set to 1 AND
2. Installer Menu Item 40, AUTO CAMPORT is enabled (1).
Selectable= Can be accessed with TV/AV key, direct access, etc.
Auto Sense= Switches to this input when connector is inserted.
The camport (Front Video) has the highest priority and will
override any commands including tuning to the Start Channel.
CAMPORT Operation (Stand-Alone)
When Camport Auto Sense is enabled as above, the TV’s source
will switch to the front video whenever a plug is inserted into
any of the front panel video inputs (either composite Video or
S-Video).
When the plug is removed, the TV will switch back to the
previous
channel or input source that the TV was using before the plug
was inserted. However, if any direct access to an RF channel or
Aux channel is requested while the camport is active, then,
when the camport plug is removed, the TV will switch to the
last requested channel. Source changes using any Source Keys
(TV/AV) are ignored. Channel Up/Channel Down and Flashback
Commands are not direct access tuning commands and they are
also ignored.
CAMPORT Operation (PPV)
The operation will be similar to that of the Stand-Alone mode.
However, the PPV providers may send different commands to
the TV for the same user commands. For instance, some
providers will always send a direct tune command when it
receives a channel up/down or a flashback command while
other PPV providers will just send a key command.
CAMPORT (Front Video) Functionality Control
Item 34
CAMPORT EN
0
0
1
1
Item 40
AUTO CAMPORT
0
1
0
1
Front Video
Operation
Disabled
Disabled
Selectable
Auto Sense
Previous State
Before Inserting
CAMPORT
Aux or RF Channel
Aux or RF Channel
Aux or RF Channel
Operation State
While CAMPORT Is
Active
None
Direct Access
Ch Up/Down,
Flashback
and TV/AV Keys
State
Upon Removal
Of CAMPORT
Previous Aux
or RF Channel
Last Requested
RF or Aux Channel
Previous Aux
or RF Channel
Previous State
Before Inserting
CAMPORT
Aux or RF Channel
Aux or RF Channel
Aux or RF Channel
Operation
While CAMPORT
Is Active
None
Direct Access
Ch Up/Down,
Flashback
and TV/AV Keys
State
Upon Removal
Of CAMPORT
Previous Aux
or RF Channel
Last Requested
RF or Aux Channel
Last Requested
Channel if PPV
translates it to direct
access tuning
command. Otherwise,
goes to Previous Aux
or RF Channel
PAGE 54
L26W56XA Aux Input Configuration / Troubleshooting
L26W56XA Aux Input Configuration
DIRECT ACCESS
Tuning
OLD_OCV
=0
130 90
Video2
(Front)
CV ONLY
34
CAMPORT_EN
0x01 0
Video Front
(Camport)
0(VIDEO) 2
Video Front
(Camport)
131 91
Video1(Rear)
CV ONLY
DTV/PC Auto
39
REAR_AUX_EN
0x02 1
Rear Video
(Aux)
0(VIDEO) 1
Rear Video
(Aux)
132 92
Component 2
91
YPrPb2 EN
0x04 2
S-Video
Rear
0(VIDEO) 5
S-Video
Rear
133 93
DVI/HDMI1
35
COMPPORT EN
0x08 3
Front
Computer
0(VIDEO) 3
Front
Computer
DTV/PC Auto
134 94
RGB1
87
REAR RGB EN
0x10 4
Computer 0(VIDEO) 4SVGA Rear
CV
S-Video
135 95
Video 3
92
RGB2 ENABLE
0x20 5
NTSC Rear
Computer
0(VIDEO)
1(S-VIDEO)
7
NTSC Rear
Computer
136 96
Component1
38
YPrPb EN
0x40 6
Rear
YPrPb
component
video
0(VIDEO)
6
YUV
Component
OLD_OCV
=1
Source Input Source Mode
Number
Value Value
Labeling LabelingLabeling
L26W56XA
ENABLE
Installer Menu
MPI DATA
STATUS TYPE
0x41 SOURCES
ENABLED (R/W)
DATA STATUS
TYPE 0xD2
CURRENT AV
SOURCE (R)
DATA
STATUS
TYPE 0X0D
AUX
SOURCE
(R)
MPI DATA
STATUS
AUX
SOURCE
ASSIGNMENT
Troubleshooting
Symptoms Possible Cause(s) Possible Solution(s) See Page(s)
Software Corrupted.
Virtual and Physical
channels appear in
channel scan w/Channel
Up/Down.
Can not direct enter
channel number
Channel not included in
channel scan in TV controller.
After 2-5-5 + MENU, only channels included in TV controller will appear.
If channel is available it can be added to channel scan. If it is not
available it will not appear on the TV screen.
2-5-5 + MENU not performed. After Auto Program and Channel List, etc. press 2-5-5 + MENU to
transfer channels and TV setup to internal TV controller. Afterward,
only Physical or only Virtual channels will appear in digital channel
scan, analog channel scan will be normal.
2-5-5 + MENU performed
more than once.
Start all over with item 117 and Enter then redo Auto Program, Channel
List, etc. *Note: 2-5-4 + MENU can be done more than once.
39
39
39
Software Problems
Some quick and easy tips to resolving problems
Troubleshooting
PAGE 55
Some quick and easy tips to resolving problems
Display Panel Picture
Symptoms Possible Cause(s) Possible Solution(s) See Page(s)
No Power. See troubleshooting flow chart. 57
Power
No Picture. • Display panel is turned off. -Turn TV on.
-Power failure?
• Antenna/Cable not connected. -Connect Antenna/Cable signal source to L26W56XA.
• Connections incorrect. -Check connections on L26W56XA.
• M.P.I. not connected. -If applicable, connect M.P.I. cable to M.P.I. device.
• Encrypted program. -Try another channel.
• Wrong tuning band. -Adjust Installer menu settings.
9~11
7 / 9~15
43~48
Erratic Operation
Installer menu setup. • Wrong Installer menu settings. -Adjust Installer menu settings as required.
• Software problem. -Remove TV power cord for 15 seconds.
43~48
Remote Control
Remote doesn’t work. • Remote not in TV mode. -Use Mode key to select TV; puts remote into L26W56XA mode.
• Not aimed at IR remote sensor. -Point remote at TV’s IR receiver on TV.
• Remote too far from IR sensor. -Move remote closer to TV’s IR receiver or darken room.
• IR path to TV’s receiver obstructed. -Remove obstructions.
• Weak batteries. -Replace batteries.
• Wrong battery polarity. -Check that “+” and “-” match in battery compartment.
• Too much light in room. -Dim room light.
• Wrong Installer remote control. -Requires compatible Installer remote, contact your LG dealer.
• Incorrect Bed 1-2 setting. -Set correct Bed 1-2 setting.
19~20
38
19
Picture Reception
Normal picture, poor
or no sound.
• Audio muted. -Press MUTE or use Volume Up key to increase sound level.
• Broadcast problem. -Try a different channel.
19~20
19~20
Broadcast Tuning Mode Digital Channel OSD
No Information
available display.
*Note: For other problems not caused by the L26W56XA, refer to other devices’ operating guide.
• Item 103 set to 1
physical channels tuning.
- Set Item 103 to 0 for information to be added to virtual
channel tuning digital OSD.
44~48
• Procedure interrupted.
• Different TV models.
• Step(s) omitted or not performed.
• Insufficient cloning time.
• Cloning erratic.
- Wait until procedure complete message is displayed.
- Cloning is only possible with identical model TVs.
- Reread 40 - 41 - 42 pages to be sure all tasks were performed.
- Redo cloning and be sure learning/teaching time is about 1 min. and
5 to15 seconds (75 seconds).
- Reset Clone Programmer.
PAGE 56
Reference: Cloning Procedure Troubleshooting
Warning: Do not use LT2002 while a LodgeNet PPV
card is installed in TV or clone programmer will be
damaged.
Reset Clone After Static Shock
After replacing exhausted batteries, or if the programmer
behaves strangely after a static shock, activate the
internal reset switch and restore normal operation.
After a reset, check the real-time clock setting. It may
be necessary to reset the Clone Programmer clock from a
TV containing the correct time.
Note
The LT2002 programmer is designed to be used with TVs con-
taining the 221-01006 and later processors. Use with earlier TV
sets may give unpredictable results. Processors used before the
221-01006-04 have a limited screen display capability. They
cannot display entire screens as shown in the quick setup
instructions accompanying the LT2002 clone programmer. Use
the printed menu illustrations on the quick setup sheet supplied
with the Clone as an aid to making your programming choices.
(Although the menus are not all displayed, the clone functions
all operate normally.)
Clone Programmer Troubleshooting
Clone Programmer
Cloning Notes: While clone is copying or transferring a master setup, do not touch or otherwise disturb clone or connections between clone
and TV. Cloning a master TV setup should take at least 45 seconds. Transferring the master TV setup to the target TV should take at least 45
seconds. Monitor LED on clone to assure that the blinking heartbeat pattern is present throughout clone operations. After cloning, be
sure to disconnect power from the target TV for about 15 seconds.
Problem Possible Cause(s) Possible Solution(s)
Remote does not
operate clone.
• Wrong Installer remote. - Only use an appropriate Installer remote to operate clone program-
mer with L26W56XA.
LED does not blink. • M.P.I. cord not connected.
• L26W56XA not turned on.
• Weak batteries.
- Connect M.P.I. cord.
- L26W56XA must be powered On for clone to work.
- Install 4 fresh AA high-quality alkaline batteries.
Clone menu hard to
read.
• Weak signal. - Connect L26W56XA to a reliable Analog channel signal source.
No time set. • Time not available. - Set time on a TV, copy time to Clone Programmer.
Clone not working. • Clone programmer problem. - Try a different LT2002 Clone programmer.
- Reset Clone Programmer.
Clone Scans Channels
more than once.
• Clone should only scan
channels once.
- Retry cloning again.
Master and Other L26W56XA
Cloning did not work.
Clone time disappeared. • Batteries were removed. - Batteries must remain installed to retain time settings.
New Setup not present. • L26W56XA not reset. - Disconnect newly cloned unit from power for 5 seconds.
• After cloning operations are complete, just unplug the LT2002 from the L26W56XA.
• If the L26W56XA does not display a picture on the TV (blank screen) after a few seconds, just change channels.
Clone Troubleshooting Flow Chart
PAGE 57
Controller
Quick
Check
Is
POWER
LED on
DTV Board
Blinking
?
Plug
into AC
Power Outlet
Is
TV
Connected to
AC Power
?
Bad
TV
Yes
No
No
Yes
Is
Red LED
on TV
lit
?
1. Bad PPV Board.
2. Bad DTV Board.
No
Cycle the power by removing
and re-connecting the AC
power cord. Observe the
’POWER’ LED and TV screen
as soon as AC power is
re-applied.
Bad
TV
Did
DTV
Board ’POWER’
LED Turn On
Momentarily
?
No
Check to see if TV
is in Commercial Mode.
See Commercial Mode
Check chart.
Did TV
Turn On
Momentarily
?
No
Yes
Yes
Yes
Did
TV Turn
On
?
Yes
No
Press ’POWER’ or ’ON/OFF’
key on TV
1. Bad TV
Press ’POWER’ or ’ON/OFF’
or ’VOLUME UP/DOWN’ or
’MUTE’ key on Remote
Did
TV
Respond
?
No
1. Bad TV
Yes
End
TV Operating Check
PAGE 58
Press the "On/Off" key
on the front panel.
The On/Off key is always operational.
Did
you get
a response
?
Bad TV
Yes
No
Did
TV stop
responding
or continue
to respond
?
TV is in
Commercial
Mode.
Stopped
responding
TV is not in Commercial Mode
Call Technical Support for
Assistance
Continued
to
respond
Leave
the
TV set On
Go to Installer menu
by pressing "MENU" until
the TV stops responding.
Glossary of Terms
PAGE 59
A list of definitions for some of the words found in this guide
75 OHM RF CABLE
The wire that comes from an off-air antenna or
cable service provider. The end looks like a
hex-shaped nut with a wire sticking through
the middle. It screws onto the Antenna/Cable
threaded jack on the back of the L26W56XA.
300 TO 75 OHM ADAPTER
A small device that connects a two-wire 300
ohm antenna to a 75 ohm RF jack.
They are usually about an inch long with two
screws on one end and a round opening with a
wire sticking out on the other end.
ANALOG TELEVISION
Standard television broadcasting format in 4:3
picture aspect ratio.
A/V CABLES
Audio/Video cables. Three cables bunched
together—right audio (red), left audio (white),
and video (yellow). A/V cables are used for
stereo playback of videocassettes and for
higher quality picture and sound from other
A/V devices.
A/V DEVICE
Any device that produces video or sound (VCR,
DVD, cable box, or television).
AMPLIFIER
An electronic device that amplifies sound from
a television, CD player, VCR, DVD, or other
Audio/Video device.
ANTENNA
The physical receiver of television signals sent
over the air. A large metal piece of equipment
does not always have to be visible to be using
an antenna.
CABLE
Cable service box. Refers to the descrambler
box cable subscribers use to receive cable
programming signals.
CATV
Programming provided by a cable service.
DIGITAL TELEVISION
High-resolution, cinema-quality television
signals transmitted digitally.
DVI
Digital Video Interface
Accommodates analog and digital interfaces
with a single connector.
COMPOSITE VIDEO
Typical video jack, uses one wire for
transporting three-color video signals.
COMPONENT VIDEO
Uses three wires for transporting three-color
video signals. The end result is usually better
video quality.
DELETED
Lets you remove channels from the list that the
end user can scroll through using CH (Channel)
Up/Down.
HDMI
High-definition multimedia interface.
HDTV
High-definition television. Refers to television
signals that have higher resolution than
ordinary analog TV signals.
HDSTB
High-definition set top box. Refers to a tuner
device that receives high-definition television
signals which have higher resolution than
ordinary analog TV signals.
INPUT
Refers to the input jack that receives a signal
from a TV, VCR, DVD Player or other
Audio/Video device.
JACK
An input or output connector on the back of a
TV, VCR, DVD Player or other Audio/Video
device.
MONO SOUND
Mono (monaural) sound is one channel of
sound. On more than one speaker, all the
speakers play the same audio.
OUTPUT
Refers to the output jack that sends a signal
out of a VCR, DVD, or other A/V device.
PHYSICAL CHANNEL NUMBER
Actual digital major, dashed minor channel
number that a station is broadcasting on.
RGB (Red, Green, Blue)
Connection input or output port available for
producing a video image using three separate
colors: Red, Green, and Blue.
2ND AUDIO PROGRAMMING/SAP
Second Audio Programming (SAP) is another,
separate audio channel available with some
programming. Choosing SAP often refers to
listening to audio in another language, such as
Spanish or French.
SIGNAL
Picture and sound traveling through a cable, or
over the air, to the TV.
STEREO SOUND
Stereo (Stereophonic) sound refers to audio
that’s divided into right and left sides.
TUNER
Device that picks up the broadcast signal and
turns it into picture and sound.
VIRTUAL CHANNEL NUMBER
The arbitrarily assigned digital dashed minor
channel number that a station is broadcasting
on.
PAGE 60
Installer Quick Setup Guide
Quick Setup Guide
for Integrated Master TVs
See table of contents for more information.
Setup Instructions for Making a Master TV
1. Connect TV to signal source, connect power cord and turn TV power on.
2. Enter the TV installer menu.
*Note: If this is not a new setup, set Installer item 117 to 001 and press Enter to
reset TV to default condition.
• Set Tuning Band.
Set Installer menu item 003 BAND/AFC to CATV: 001, Broadcast: 000 etc.
• If necessary, set Installer menu item 028 CH OVERIDE to 001.
In addition, set any other installer items as required of your system.
Exit Installer menu.
3. Access the Master TV menus and set the clonable options on the menus to the
desired configurations. Refer to the Clonable Menu Features Chart for the TV.
(Picture, Sound, Time etc.)
4. Do a Channel Search; run Auto Program. (aka EZ Scan.)
5. Enter the Channel Edit menu and delete channels per your requirements.
6. Enter the Channel Label menu and assign ICONs to the channels.
*Note: You can add Channel ICONStypically network logos like ABC, NBC, PBS etc. in
this step. Or, in Step 8, add Channel ICONSor custom text labels for channels which no
Icons are available for.
7. Transfer the TV setup. After all menu options and features are set to your
requirements, enter the installer menu. Press ‘2’, ‘5’, ‘5’, ‘MENU’ to start the transfer
of the TV’s setup to the PTC.
After the transfer is complete, the system will exit the Installer menu.
8. Set any Channel Labels as needed.
a. Enter Installer menu.
b. Press ‘2’, ‘5’, ‘4’, ‘MENU’ to enter the menu. In this menu edit the assigned
channel Icons, assign custom text labels for channels and assign labels for active
Aux sources. Press ‘Menu’ to exit.
9. Enter the Installer menu. Set item 028 Ch Overide to 000 and exit menu.
L26W56XX PTC INSTALLER MENU
117 FACT DEFAULT 00X
028 CH.OVERIDE 001
028 CH.OVERIDE 001
028 CH. OVERIDE 000
000 INSTALLER SEQ 000
UPN 000-000-000-000 FPGA 09F1
PTC V1.00.000 CPU V1.01.00
WXYZ
DIGITAL 19-3
MONO SAPSTEREO
WXYZ
ANALOG 2
MONO
Antenna
Wall Jack
AC Power
Cord
RF Coaxial Wire
(75ohm)
Sound
Mode Standard G
Balance
Auto Volume
On
Digital Output
PCM
English
Multi-Track
Internal Speaker
On
11:20 PM
Sep.11, 2006
Channel
Antenna
Auto Program G
Channel Label
Channel List
Fine Tune
Signal Strength
--:-- --
--.-- ----
Antenna
Auto Program
Channel Label
Channel List
Fine Tune
Signal Strength
--:-- --
--.-- ----
Picture
11:20 PM
Sep.11, 2006
Mode
Color Temperature
Standard
G
Contrast 100
Brightness 79
Sharpness 65
Color 70
Tint 0
Screen Format
Noise Reduction
Film Mode
PAGE 61
Notes
PAGE 62
Notes
PAGE 63
Notes
Your Zenith LCD TV/Monitor Warranty
Welcome to the LG family! We believe that you will be pleased with your LCD TV/Monitor. Please read this warranty carefully, it is a “LIMITED
WARRANTY” as defined under Federal Law. This warranty gives you specific legal rights, and you may also have other rights that vary from
state-to-state within the U.S.A.
LCD TV/Monitor
During a period of one year from effective warranty date, LG will provide service labor by a LG authorized service center when needed, as
determined by the LG service center, as a result of manufacturing defects.
Service Labor
Warranty begins on the date of installation of the Commercial Products LCD TV/Monitor.
For your convenience, keep the dealer’s dated bill of sale or delivery ticket as evidence of the purchase date.
Effective Warranty Date
Read the Installation and Operating Guide carefully so that you will understand the operation of the unit and how to adjust the controls.Operating Guide
Reception problems caused by inadequate antenna or faulty antenna connections are the owner’s responsibility.Antenna
For warranty service information, call 1-888-865-3026. Parts and service labor that are LG’s responsibility (see above) will be provided without
charge. Other service is at the owner’s expense. If you have any problem in obtaining satisfactory warranty service, call 1-888-865-3026.
• You must provide the model number, serial number and date of purchase or date of original installation.
• Before you ask for warranty service, read “Troubleshooting” in this installation guide. You might avoid a service call.
Marketed and Distributed in the United States by LG Electronics U.S.A., Inc.
2000 Millbrook Drive, Lincolnshire, IL 60069.
© Copyright 2007 LG Electronics U.S.A., Inc.
Warranty Service
New or remanufactured replacements for factory-defective parts will be supplied by an LG authorized service center for one year from effective
warranty date (color picture tube — two years). Such replacement parts are warranted for the remaining portion of the original warranty period.
Parts
Warranty service is provided. (Some repairs may require the unit to be taken by the service to the repair facility and returned, at no additional
charge.) Call 1-888-865-3026 for further information.
Warranty Service
This warranty covers manufacturing defects and does not cover installation, adjustment of customer controls, installation or repair of antenna
systems, cable converters or cable company-supplied equipment; it also does not cover damage due to misuse, abuse, negligence, acts of God or
other causes beyond the control of LG. Any alteration of the product after manufacture voids this warranty in its entirety.
THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTY, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, AND NEITHER THE MANUFACTURER NOR ITS DISTRIBUTORS SHALL NOT BE LIABLE
FOR ANY CONSEQUENTIAL, INDIRECT, OR INCIDENTAL DAMAGES OF ANY KIND, INCLUDING LOST REVENUES OR PROFITS IN CONNECTION WITH
THIS PRODUCT. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU.
Not Covered
LG’S RESPONSIBILITY
OWNER’S RESPONSIBILITY
For Customer Support/Service
Please call:
1-888-865-3026
www.zenith.com
www.lgcommercial.com
P/NO : 3350GDKM0004A GPN06MA016Q a
