Loading ...
Loading ...
Loading ...
15
DRB1502-E
En
15
Additional information
Additional information
Troubleshooting
! Incorrect operation is often mistaken for trouble or malfunction. If you think that there is something wrong with this component, check the points
below. Sometimes the trouble may lie in another component. Inspect the other components and electrical appliances being used. If the trouble can-
not be rectified after checking the items below, ask your nearest Pioneer authorized service center or your dealer to carry out repair work.
! This unit may not operate properly due to static electricity or other external factors. In this case, normal operation may be restored by unplug-
ging the power cord, waiting about 5 seconds or more, then plugging the power cord back in.
Problem Check Remedy
The power is not turned on. Is the power cord properly connected? Plug in the power cord to an AC outlet. (page 8)
No sound or small sound. Is the [CD, PHONO] (input selector) switch set to
the proper position?
Switch the [CD, PHONO] (input selector) switch to select the
input source for that channel. (page 10)
Are the [TRIM], [channel fader], [crossfader] and
[MASTER LEVEL] controls set to the proper posi-
tions?
Set the [TRIM], [channel fader], [crossfader] and [MASTER
LEVEL] controls to the proper positions. (page 10)
Are the connected components, amplifiers, etc.,
properly set?
Set the external input selection, volume, etc., on the components/
amplifiers properly.
Are the connection cables properly connected? Connect the connection cables properly. (page 8)
Are the terminals and plugs dirty? Clean the terminals and plugs before making connections.
Distorted sound. Is [MASTER LEVEL] set at the proper position? Adjust [MASTER LEVEL] so that the orange indicator on the mas-
ter level indicator lights at the peak level. (page 10)
Is [TRIM] set at the proper position? Adjust [TRIM] so that the orange indicator on the channel level
indicator lights at the peak level. (page 10)
Can’t crossfade.
Is the [THRU,
,
] (crossfader curve selector)
switch set to [THRU]?
Set the [THRU,
,
] (crossfader curve selector) switch to a
position other than [THRU]. (page 10)
Can’t fader start a DJ player. Is [FADER START] set to off? Set [FADER START] to on. (page 11)
Is the control cord properly connected? Connect this unit and DJ player with a control cord. (page 8)
Are the audio cables properly connected? Connect this unit to the audio output terminal of a DJ player with
an audio cable. (page 8)
No effect. Has one of the [MASTER EFFECT (GATE, CRUSH,
JET, FILTER)] buttons been pressed?
Press one of the [MASTER EFFECT (GATE, CRUSH, JET, FILTER)]
buttons. (page 12)
Is [LEVEL/
DEPTH] set to the center position? Turn [LEVEL/
DEPTH] clockwise or counterclockwise. (page 12)
No sound is produced or the sound is faint
when playing a track recorded on a USB
device.
Is [MASTER LEVEL] set at the proper position? Before recording, adjust [MASTER LEVEL] so that the orange
indicator on the master level indicator lights at the peak level.
(page 10)
Sound is distorted when playing a track
recorded on a USB device.
Is [TRIM] set at the proper position? Before recording, adjust [TRIM] so that the orange indicator on
the channel level indicator lights at the peak level. (page 10)
The sound of a recorded track cannot be pre-
viewed over the headphones even when [TRACK
MARK (PREVIEW)] is pressed and held.
Is [MIXING] turned all the way clockwise?
Turn [MIXING] counterclockwise from the center position. (page 13)
USB device is not recognized. Is the USB device properly connected? Insert the USB device securely all the way in. (page 13)
Is the USB device one that can be used on this
unit?
This unit supports such USB mass storage class USB devices as
external hard disks and portable flash memory devices.
Sound is distorted when an analog player is
connected to this unit’s [PHONO] terminals.
Or, lighting of the channel level indicator does
not change even when the [TRIM] control is
turned.
Have you connected an analog player with a built-
in phono equalizer?
If the analog player is equipped with a built-in phono equalizer,
connect it to the [CD] terminals. (page 8)
If the analog player with built-in phono equalizer has a PHONO/
LINE selector switch, switch it to PHONO.
Is an audio interface for computers connected
between the analog player and this unit?
If the computer audio interface’s output is line level, connect it to
the [CD] terminals. (page 8)
If the analog player has a PHONO/
LINE selector switch, switch
it to PHONO.
Loading ...
Loading ...
Loading ...