Loading ...
Loading ...
Loading ...
10
HOT WATER
1. Turn the appliance on by turning the selector dial to
(g. 4). Wait the READY indicator light comes on;
2. Place a recipient under the cappuccino maker;
3. When the READY indicator light comes on, turn the se-
lector dial to the position and at the same time,
rotate the steam dial counterclockwise: Hot water is deliv-
ered from the cappuccino maker;
4. To interrupt delivery of hot water, rotate the steam dial
clockwise and turn selector dial to ON.
You should not deliver hot water for more
than 60 seconds.
CLEANING
Cleaning the machine
The following parts of the machine must be cleaned regularly:
- the coee lters (2-3);
- the boiler outlet (15);
- the water tank ( 18);
- the cappuccino maker (17) as described in section “Clean-
ing the cappuccino maker after use”.
Important!
• Do not use solvents, abrasive detergents or alcohol to clean
the coee machine. A soft, damp cloth is sucient.
• Do not use metal objects to remove encrustations or coee
deposits as they could scratch metal or plastic surfaces.
Danger! While cleaning, never immerse the coee
maker in water. It is an electrical appliance.
Please note:
If the appliance is not used for more than 3/4 days, before using it again, we strong-
ly recommend you rinse the internal circuits through as described in Setting up the
appliance”.
Cleaning the coee lters
About every 200 espressos or when the espresso drips out of the
lter holder or not at all, clean the ground coee lter holder
as follows:
• Remove the lter from the lter holder.
• Clean the inside of the lter holder. Never wash in a
dishwasher.
• Remove the lter cap (g. 22) by unscrewing in the
direction indicated by the arrow on the cap.
• Remove the lter from the container by pushing it from the
cap end.
• Remove the gasket.
• Rinse all components and clean the metal lter thoroughly
in hot water using a brush (g. 23). Make sure the holes in
the metal lter are not blocked. If necessary, clean with a
pin (see g. 24)
• Replace the lter and gasket on the plastic disk as shown in
g. 25. Make sure to insert the pin on the plastic disk into
the hole in the gasket indicated by the arrow in g. 26.
• Replace the resulting assembly in the steel lter container
(g. 26), making sure the pin is inserted into the hole in the
support (see arrow in g. 26).
• Finally, screw on the cap (g. 27).
Failure to clean as described above invalidates the warranty.
Cleaning the boiler outlet
About every 300 coees, the espresso boiler outlet must be cle-
aned as follows:
• Make sure the appliance is not hot and that it is unplugged
from the outlet.
• Using a screwdriver, unscrew the screw connecting the
espresso boiler outlet lter (g. 28);
• Clean the outlet lter thoroughly in hot water using a
brush.
Make sure the holes are not blocked. If necessary, clean
with a pin (g. 24).
Failure to clean as described above invalidates the warranty.
Cleaning the water tank
1. Clean the water tank regularly (about once a month) with
a damp cloth and a little mild washing up liquid;
2. Rinse with running water;
3. Fill the tank with fresh water and replace the tank.
DESCALING
We recommend descaling the coee maker about every 200
coees. We recommend using the De’Longhi descaler (purchase
separately).
Proceed as follows:
1. Fill the tank with the descaler solution, obtained by dilut-
ing the descaler with water up to the max level;
2. Turn the selector dial to the
position;
3. Make sure the lter holder is not attached and place a re-
cipient under the cappuccino maker;
4. Wait until the READY light comes on;
5. Turn the selector to the
position and deliver
about 1/4 of the solution in the tank: from time to time
turn the steam dial to the
position
to discharge
steam. Then interrupt delivery by turning the selector to
the ON position and leave the solution to work for about 5
minutes;
6. Repeat point 5 another 3 times, until the tank is empty;
Loading ...
Loading ...