EN
FULLY AUTOMATIC ESPRESSO
COFFEE MACHINE
Translation of the original manual
SES 6100BK
SES 6100BK
A
9
1
3
5
7
11
13
15
1
3
5
7
9
11
13
15
1
2
3
9
13
12
4
5
6
7
8
10
11
14
B
DOUBLE ESPRESSO
CLEAN NO BEAN
+
NO WATER CLEAN BREWER WARNING CLEAR DREGS CLEAR GRINDER
ESPRESSO LUNGO AMERICANO DOSE VOLUME
!
+
8 9 10 11 12
654321
13 14
7
C
PUSH
D1
D2
9
1
3
5
7
11
13
15
1
3
5
7
9
11
13
15
- 1 -
07/2025
2025, .
EN
Fully Automatic Espresso Machine
User Manual
Important Safety Instructions
READ CAREFULLY AND STORE FOR FUTURE USE.
• This appliance is not to be used by children. Keep this
appliance and its power cable out of the reach of children.
• The appliance may be used by persons with reduced
physical, sensory or mental abilities or lack of experience
and knowledge, provided they are supervised or have
been instructed on the safe use of the appliance and
understand the potential hazards.
• Children must not play with the appliance.
• Cleaning and maintenance must not be carried out by
children.
• If the power cord is damaged, have it replaced in
aprofessional service centre in order to prevent
adangerous situation. Never use the appliance if the
power cord is damaged.
• Always clean the parts of the appliance that come into
contact with food with clean warm water and alittle neutral
dishwashing liquid, rinse them with clean water and wipe
dry.
WARNING:
Incorrect use may lead to injury.
- 2 -
07/2025
2025, .
• Always disconnect the appliance from the power supply
when leaving it unattended and before assembly,
disassembly or cleaning.
• This appliance is intended for household use. It is not
intended for use in areas such as:
– kitchenettes in shops, offices and other workplaces;
– agricultural premises;
– hotel, motels and other residential areas;
– bed and breakfast establishments.
WARNING:
Prevent the plug from getting wet.
WARNING:
The outer surface of the appliance heats up during
use and may be hot for some time after use. Be very
careful.
• The appliance must not be placed in acabinet when in
use.
WARNING:
The filling hole must not be opened during use.
Do not do submerge the power cable, plug or
appliance in water or any other liquid.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ELECTRICAL SAFETY
• Before connecting the appliance to apower socket, make sure that its nominal voltage indicated on the rating plate matches the electrical voltage of
the socket.
• Connect the appliance only to aproperly earthed socket. For safety reasons, we do not recommend using adaptors or extension cables.
• Do not place the appliance on windowsills, sink drain trays or unstable surfaces. Always place the appliance on astable, flat and dry surface.
• Do not place the appliance on an electric or gas stove or near an open flame.
• Never use the appliance in the immediate vicinity of abath, shower or swimming pool.
• Use the appliance only for its intended purpose.
• Use the appliance according to the instructions in this user manual. Failure to do so may result in injury, damage to the appliance, or ahazardous
situation.
• Use the appliance only with the original accessories supplied with it.
• Leave at least 15 cm of free space around and above the appliance to ensure proper air circulation during operation.
- 3 -
07/2025
2025, .
• Do not place any items on the top surface of the appliance.
• Fill the water tank with clean, cold water. Do not pour hot water or other liquids into it or place any objects inside it.
• Before turning on the appliance, make sure that:
– the drip tray with grid is installed in its place;
– the water tank is filled with asufficient amount of water and is properly installed in its position;
– the bean hopper is filled with fresh coffee beans.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SAFETY IN USE
• The water level must not exceed the maximum mark.
• Take extra care when operating the appliance to avoid scalding with hot water or steam.
• The hot water function may only be used continuously for amaximum of one emptying of the entire water tank.
• When using the appliance, check the water level in the water tank regularly. If the water level falls below the minimum mark, refill the water tank.
Before adding water, first turn the appliance off and disconnect it from the power socket.
• Use the built-in coffee grinder only for grinding coffee beans. Do not use it for any other purposes.
• Ensure that no hair or other items enter the grinder area during the grinding process. The coffee bean hopper lid should always be properly closed
unless you are refilling coffee beans or adjusting the grind fineness.
• The appliance is equipped with abuilt-in thermal fuse that shuts it off when the pump is idling to prevent damage. If such asituation occurs, unplug
the power cable and allow the appliance to cool down for at least 30 minutes. Then you can use it again.
• Do not move the appliance if there is acup of coffee on the drip tray grille.
• Ensure that the power cable does not come into contact with hot surfaces.
• Unplug the appliance from the power socket by pulling on the plug, not the power cable. Otherwise, you may damage the power cable or the
socket.
• Do not submerge the appliance, power cable or plug in water or any other liquid.
• Make sure that the power cable and plug do not come into contact with water or other fluids.
• To avoid the risk of electric shock, do not repair or modify the appliance yourself. All repairs should be carried out by an authorised service centre.
Tampering with the appliance may result in the loss of your legal rights regarding faulty performance or warranty for quality.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EXPLANATION OF SYMBOLS PLACED ON THE PRODUCT OR INTHE ACCOMPANYING DOCUMENTATION
The product meets all the basic requirements of the applicable EU directives.
This symbol on products or accompanying documents means that used electric or electronic products must not be added to ordinary
municipal waste.
This symbol indicates ahot surface warning.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
- 4 -
07/2025
2025, .
• Thank you for purchasing our SENCOR product; we hope it will serve
to your satisfaction.
• Before using this appliance, please familiarise yourself with the user
manual, even if you are already familiar with using similar types of
appliances. Use the appliance only as described in this user manual.
Keep the manual for future reference.
• It is recommended to keep the original packaging, packing material,
receipt and confirmation of the extent of the seller'sliability or warranty
certificate at least for the duration of the legal right to file defect
claims or the quality warranty. When transporting the appliance,
we recommend repackaging it in the original box provided by the
manufacturer.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DESCRIPTION OF THE COFFEE MACHINE
A1 Bean hopper lid
A2 Bean hopper, capacity 180 g
A3 Grinding coarseness regulator
A4 Control panel
A5 Coffee spout head
(adjustable height)
A6 Coffee grounds container
A7 Drip tray grid
A8 Drip tray
A9 Water tank lid
A10 Water tank, capacity 1.5 l
A11 Service door
A12 Tamper
A13 Brewing unit
A14 Brewing unit handle
Not shown: Cleaning brush, power cord
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DESCRIPTION OF THE CONTROL PANEL
B1 DOUBLE ESPRESSO button:
start brewing Espresso
(2 cups)
B2 ESPRESSO button: start
brewing Espresso (1 cup)
B3 LUNGO button: start brewing
lungo
B4
button: switch coffee
machine on/off
B5 AMERICANO button: start
brewing Americano (Espresso
+ hot water)
B6 DOSE button: to adjust the
amount of ground coffee
B7 VOLUME button: for
setting the volume of coffee
dispensed
B8 CLEAN button: manual
cleaning
B9 NO BEAN indicator light:
empty bean hopper warning
B10 NO WATER indicator light: for
empty water tank warning
B11 CLEAN BREWER Indicator
light: warning for cleaning the
brewing unit
B12 WARNING indicator light
B13 CLEAR DREGS Indicator light:
full coffee grounds container
warning
B14 CLEAR GRINDER button:
grinder empty
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BEFORE FIRST USE
• Before first use, remove the appliance and its accessories from the
packaging and discard all promotional labels and tags. Check that
neither the appliance nor any of its components is damaged.
• Remove the protective foil from the control panel.
• Install the appliance on aflat, dry and clean surface.
• Remove the water tank, the brewing unit, the drip tray, the grid and the
coffee grounds tank. Wash them with clean water and asmall amount
of neutral kitchen detergent. Then rinse them properly with clean
water, dry them and put them back in place.
• Remove the protective cap from the outlet of the water tank. It serves
as protection during transport and must be removed before using the
coffee machine.
• Wipe the outer surface of the appliance with aslightly damp cloth and
then wipe dry properly.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
POSITIONING THZE COFFEE MACHINE
• Place the coffee machine on aflat, dry and clean surface at
asufficient distance from the mains socket.
• Ensure there is enough free space around it for manipulation, at least
15 cm on all sides.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PREPARING THE COFFEE MACHINE BEFORE
USE
Filling the water tank
1. Carefully remove the water tank.
2. Grab the handle and remove the water tank from the rear of the
appliance.
3. Fill the water tank with clean water up to the maximum mark and
insert it back into the appliance. Make sure that the water tank is
properly installed in its place.
Note:
The water you pour into the water tank should ideally be
at room temperature (approximately 25 °C). Too cold water
can negatively affect the final taste of the coffee beverage.
Caution:
The maximum capacity of the water tank is 1.5 l. Do
not overfill it.
Never fill the water tank with warm or hot water,
sparkling water or other liquids such as milk. This
could damage the appliance.
Never fill the water tank by pouring water into in while
it is inserted inside the appliance. You risk splashing
the appliance overfilling the water tank.
Note:
Do not leave water in the water tank for more than one day.
For preparing quality fresh coffee, it is necessary to always
use fresh water. Using water that is not fresh will affect the
taste of the final beverage.
Filling the coffee bean hopper
1. Remove the coffee bean hopper lid.
2. Pour roasted coffee beans into the hopper and close the lid. Do not
leave the lid of the hopper open, otherwise the coffee beans will lose
their aroma more quickly.
Caution:
Themaximum capacity of the hopper is 180 g of
coffee beans. Do not overfill it.
Never fill the hopper with ground or instant coffee,
caramelised or otherwise specially treated coffee
beans, cocoa beans or other items that may damage
the appliance.
Adjusting the grind fineness
Use the grinding coarseness regulator to adjust the appropriate
coarseness of the ground coffee. Grinding coarseness adjustment is
possible only when the grinder is in operation. The new coarseness
setting will take effect after the second or third coffee preparation following
the grinding coarseness change.
1. Use the grinding coarseness regulator inside the coffee bean hopper to
adjust the coarseness in 15 levels. For first use, we recommend setting
the grinding coarseness to 8 and then adjusting as needed.
EN
Fully Automatic Espresso Machine
User Manual
- 5 -
07/2025
2025, .
2. Turn the regulator clockwise to set acoarser grind, turn
counterclockwise to set afiner grind. Always adjust by one level. Try it
out and then readjust as needed.
3. Only adjust the grinding coarseness when the grinder is running.
Otherwise, damage to the appliance may occur.
4. If the brewed coffee flows out very slowly, it means that the beans
are ground too finely and acoarser grind should be set. If the brewed
coffee flows out too quickly, it means that the grains are ground too
coarsely and afiner grind should be set.
Adjusting the Head Height
• The head can be moved up/down according to the height of the cup in
which you will be preparing the coffee. First, place the cup under the
head and then adjust the height.
Brewing unit
• Gently press on the centre of the upper part of the service door (it
is marked with aPUSH). The top part of the service door slides out.
Remove it and check that the brewing uniit is properly installed. When
inserting the brewing unit into the coffee machine, align the arrow on
the brewing unit with the arrow above the brewing unit compartment -
see figure C. After you check, close the service door.
• If you remove and reinsert the brewing unit and hear aclick, it
indicates that the brewing unit is properly installed.
• If the WARNING indicator light is continuously on, the brewing unit is
not installed correctly.
• If the WARNING indicator light blinks when you press the beverage
preparation button, the service door is not closed properly.
Drip Tray andCoffee Grounds Container
• Place the coffee grounds container on the drip tray.
• Insert the drip tray into the coffee machine.
• Attach the grid to the outside of the drip tray.
• The grid must be firmly secured to prevent the cup with hot beverage
from tipping over during preparation.
• Water from the spout flows into the drip tray during each rinse, self-
cleaning, and also any coffee that may spill during brewing. Therefore,
clean and empty the drip tray daily.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CONNECTING TO THE POWER SUPPLY
• Fully unwind the power cord.
• Make sure the water tank is filled with fresh water, there is asufficient
amount of coffee beans in the hopper, and the appliance is properly
assembled.
• Plug the mains plug into aproperly grounded power socket.
• You will hear ashort beep, the control panel buttons will briefly light
up, then go out. The coffee machine will enter the sleep mode.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
USING THE COFFEE MACHINE
Turning On the Coffee Machine, Rinsing, and Preheating
• Place acup or abowl that can hold at least 100 ml under the coffee
spout.
• Long press the button to switch on the coffee machine. Ashort
beep will sound, the button will start blinking andthe CLEAN button
will light up.
• When switching on for the first time, the coffee machine starts heating
up, and the preparation process begins, during which water is pumped
into the internal circuit, the grinder is checked, and the coffee spout is
rinsed, with aproportional amount of water flowing into the cup (the
proportional amount of water is slightly greater than the amount of
water during normal switching on and automatic rinsing). During this
time, the grinder and pump will briefly operate. This is normal.
• Each time you turn it on, the coffee machine starts heating up, the
preparation process begins, the grinder is checked, and the spout is
rinsed, with asmall amount of water flowing into the cup. During this
time, the grinder and pump will briefly operate. This is normal.
• Then the coffee machine will warm up. During this time, the buttons
from DOUBLE ESPRESSO to VOLUME will gradually blink. The coffee
machine cannot be operated during this time.
• Once the control buttons light up, the coffee machine is ready to use.
Note:
You can skip the rinsing process by pressing the CLEAN
button after turning on the coffee machine. The preheating
process will begin right away.
Turning off the coffee machine
• When you have finished using the coffee machine, press the
button to turn it off. The coffee machine will enter the sleep mode.
• To switch the appliance completely off, unplug the power cord from
the socket.
Note:
The coffee machine is equipped with an automatic shut-off
and switch to sleep mode function. This occurs after 28
minutes of inactivity. This is normal.
Automatic Rinsing
• Each turn on and off of the coffee machine is accompanied by ashort
rinsing of the entire system. In both cases, both the outlet and the
brewing unit are rinsed. Asmall amount of water will flow from the
outlet, so place acup under the outlet with amin. volume of 100 ml.
• When the brewing unit is flushed, some of the water gets into
the spent coffee grounds container. This is normal. Therefore, we
recommend regularly emptying the spent coffee grounds container
so that the coffee does not come in contact with the rinse water. Pour
out the water from the rinse, clean the containers, dry them and return
them to their place.
Preparing Espresso (1 and 2 Cups), Lungo, Americano
1. Place acup, mug or glass under the head. Adjust the height of the
head by moving it up or down depending on the size of the cup, mug
or glass.
2. Press the ESPRESSO button (for preparing 1 cup of Espresso),
DOUBLE ESPRESSO (for preparing 2 cups of Espresso) LUNGO (for
preparing Lungo) or AMERICANO (for preparing Americano). The
selected button will light up, the other buttons will turn off.
3. The coffee machine will automatically start the process of grinding,
dosing, tamping the coffee, and dispensing it.
4. Once the coffee dispensing process is complete, you will hear asound
alert, the button will briefly blink, indicating that the coffee machine
is heating up to operating temperature. Once the control panel lights
up, the coffee machine is ready to make another coffee.
• Preparing 2 cups of Espresso involves two consecutive preparations
of 1 cup of Espresso. Do not remove the cup from under the head until
the preparation of the second cup is complete.
• Preparing Americano coffee consists of preparing 1 cup of Espresso
and adding hot water. Do not remove the cup from under the brew
head until the hot water dispensing is finished.
• You can cancel the coffee preparation by pressing the button of the
drink being prepared.
• You can adjust the amount of ground coffee and the volume of coffee
dispensed according to your personal preferences by following the
instructions inthe "USER SETTINGS" section.
Note:
During the coffee preparation process, you may hear the
sound of the grinder and pump, and after preparation, the
sound of used ground coffee being expelled into the coffee
grounds container. These are normal sounds.
Note:
At the beginning of the coffee dispensing process, coffee
may drip slowly (2 to 3 seconds after brewing), and then
the full coffee dispensing will start. After the dispensing is
complete, the coffee may drip from the spout for about 6 to
8 seconds. This is normal.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
- 6 -
07/2025
2025, .
USER SETTINGS
Adjusting the Amount of Ground Coffee
• The amount of ground coffee affects the intensity (strength) of the
brewed coffee.
• Press the DOSE button repeatedly to adjust the amount of ground
coffee. Each time it is pressed, one LED above the button will be lit. In
total, three indicator lights may light up:
– One light represents the initial amount of ground coffee
(approximately 9g of ground coffee).
– The two lights represent alarger amount of ground coffee
(approximately 11g of ground coffee).
– The three lights represent the highest amount of ground coffee
(approximately 13g of ground coffee).
Note:
The amount of ground coffee depends on several factors,
such as the type of coffee, the degree of roasting or the
fineness of the grinding.
–
Adjusting the amount of coffee dispensed
• Press the VOLUME button repeatedly to adjust the amount of coffee
dispensed. Each time it is pressed, one LED above the button will be
lit. In total, three indicator lights may light up:
– One light represents the default volume of dispensed coffee.
– Two indicator lights represent alarger volume of dispensed coffee.
– Three indicator lights represent the highest volume of dispensed
coffee.
Coffee VOLUME button Coffee quantity (ml)
DOUBLE ESPRESSO
2× 30
2× 40
2× 50
ESPRESSO
30
40
50
LUNGO
50
60
70
AMERICANO
100
110
120
Note:
The amount of ground coffee depends on several factors,
such as the type of coffee, the degree of roasting or the
fineness of the grinding.
Note:
Adjust the amount of ground coffee or the volume of coffee
dispensed before pressing the button of the selected
beverage. While the coffee is brewing, the buttons are
inoperative.
Restoring default factory settings
• If you need to restore the factory settings and erase all your
customised settings, perform afactory reset.
• Press the DOUBLE ESPRESSO and ESPRESSO buttons
simultaneously for 2 seconds.
• The coffee machine beeps briefly, press the button to switch the
machine on. Ashort beep will sound and the button will flash shortly.
• When all buttons light up, the factory reset has been completed.
EMPTYING THE GRINDER
• This function is used to empty the grinder and remove any coffee
beans inside it if you won't be using the coffee machine for an
extended period to prevent them from deteriorating.
1. Empty the coffee bean hopper.
2. Press the CLEAR GRINDER button to start the grinder emptying
function. The button will light up.
3. The grinder will stop after about 15 seconds. If the grinder is still full,
run the function again.
4. Empty the coffee grounds hopper.
5. You can cancel the emptying function of the grinder by pressing the
CLEAR GRINDER button.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CLEANING AND MAINTENANCE
Before cleaning, switch off the coffee machine and unplug the power cord
from the mains socket and allow the appliance to cool down.
Caution:
Do not use abrasive cleaning agents, solvents, etc.
to clean any parts of the appliance, as these could
damage the surface. None of the components of this
appliance are dishwasher safe.
Caution:
To prevent the risk of electric shock, do not immerse
the appliance, power cable, or plug into water or any
other liquid.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OVERVIEW OF CLEANING AND MAINTENANCE
OF THE COFFEE MACHINE
PART OF THE COFFEE
MACHINE
WHEN TO CLEAN
Coffee grounds hopper
Every day, or when the CLEAR
DREGS indicator lights up
Brewing unit At the same time as the coffee
grounds container
Water Tank Every day
Drip tray Every day
Grinder Once aweek, or when you refill
anew type of coffee
Bracket Seat Switch Once aweek
Ground Coffee Dispensing
Channel
Once aweek
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DAILY CLEANING AND MAINTENANCE
Regular cleaning and maintenance are crucial for the proper functioning
and longevity of the appliance.
Manual Rinsing
We recommend cleaning the coffee outlet after each use. This is also
recommended when the appliance has not been used for an extended
period of time.
1. Press the CLEAN button to initiate the manual rinsing process. Several
rinses and hot water dispensing will occur. Pour out the water.
2. The manual rinsing process will automatically stop, and you will hear
asound alert, the button will briefly blink, indicating that the coffee
machine is heating up to operating temperature. Once the control
panel lights up, the coffee machine is ready to make another coffee.
3. You can cancel the manual rinsing process by pressing the button
CLEAN.
• Manual flushing is alarger flushing of the entire system. Inboth
cases (manual rinsing and rinsing when switched on or off), the outlet
- 7 -
07/2025
2025, .
and the brewing unit are rinsed. Alarger amount of water will flow
out of the outlet, so place acup under the outlet of volume of min.
300ml. When the brewing unit is flushed, some of the water gets
into the spent coffee grounds container. This is normal. Therefore, we
recommend regularly emptying the spent coffee grounds container
so that the coffee does not come in contact with the rinse water. Pour
out the water from the rinse, clean the containers, dry them and return
them to their place.
Drip Tray and Coffee Grounds Container
• The drip tray should be emptied daily.
• Carefully pull out the drip tray from the coffee machine. Remove the
grid and the coffee grounds container.
• Pour the contents of the drip tray into the sink.
• Empty the coffee grounds container into the municipal waste or
compost.
• Clean the drip tray, grid and coffee grounds container with warm water
and alittle dishwashing detergent. Rinse and wipe dry.
• Place the coffee grounds container on the drip tray.
• Insert the drip tray into the coffee machine.
• Attach the grid to the outside of the drip tray.
Caution:
Be careful not to scald yourself when handling the
tray. It may contain hot water.
Full coffee grounds hopper warning
• Empty the coffee grounds container whenever the CLEAN DREGS
indicator light comes on. The coffee grounds container has acapacity
of 8 coffee servings or 4 if it is aDouble Espresso (the grinder grinds
two servings in arow). When emptying the container, ensure the
coffee machine is turned on to reset the counter.
• Carefully pull out the drip tray from the coffee machine.
• Empty the coffee grounds container into the municipal waste or
compost.
• Clean the drip tray, grid and coffee grounds container with warm water
and alittle dishwashing detergent. Rinse and wipe dry.
• Place the coffee grounds container on the drip tray.
• Insert the hopper into the coffee machine.
Brewing unit
• We recommend cleaning the brewing centre at the same time as
emptying the coffee grounds container.
• Gently press on the centre of the upper part of the service door (it
is marked with aPUSH). The top part of the service door slides out.
Lower them.
• Press both latches on the brewing unit and remove it from the coffee
machine (Figure C).
• Wash it under running water and then dry it properly.
• Insert the brewing centre back into the coffee machine, aligning the
arrow on the brewing centre with the arrow above the brewing centre
compartment. Aclick indicates that the brewing centre is correctly
installed.
• Close the service door.
Note:
• If the warning indicator light WARNING is continuously
on, the brewing unit is not installed correctly.
• If the warning indicator light WARNING blinks when you
press the beverage preparation button, the service door is
not closed properly.
Water Tank
• Remove the water tank, rinse it with clean water, dry it and put it back
in its place.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REGULAR MAINTENANCE
Perform regular maintenance of the coffee machine at least once aweek.
Coffee Bean Hopper and Grinder
1. Empty the coffee beans from the hopper and store them in an airtight
container.
2. Start the emptying function of the grinder with the CLEAR GRINDER
button.
3. Turn the grinding coarseness regulator counterclockwise until the tabs on
the regulator are aligned with the notches on the grinder (figure D1).
4. Lift the regulator upward and remove it from the grinder.
5. Lift the handle of the upper grinding stone and turn it counterclockwise
in the direction of the “ “ symbol.
6. Remove the upper grinding stone and clean it using acleaning brush.
If the grinding stone is clogged with coffee bean oil, we recommend
degreasing them.
7. Clean the lower grinding stone and chamber using acleaning brush.
8. Insert the upper grinding stone into the grinding chamber, aligning the
“ “ symbol with the arrow on the grinder outlet (Figure D2).
9. Rotate the handle of the upper grinding stone clockwise in the
direction of the “ “ symbol. Lower the handle.
10. Attach the grinding coarseness regulator, ensuring that the tabs on the
regulator fit onto the notches on the grinder (Figure D1) and rotate the
regulator clockwise.
Bracket Seat Switch
1. While the coffee machine is switched on, press the CLEAN
andDOUBLE ESPRESSO buttons simultaneously until they start
blinking.
2. The brewing unit holder will enter the brewing coffee position.
3. Open the service door and wipe the bracket and the area underneath
it.
4. After cleaning, close the service door and then press the CLEAN
andDOUBLE ESPRESSO buttons simultaneously. The bracket will
retract back to its original position.
5. The
button will briefly blink, indicating that the machine is heating
up to operating temperature. Once the control panel lights up, the
coffee machine is ready to make another coffee.
Ground Coffee Dispensing Channel
The ground coffee dispensing channel can be cleaned using the following
steps.
1. Press the CLEAR GRINDER and ESPRESSO buttons simultaneously
until they start blinking.
2. The cover of the ground coffee dispensing channel, located above the
tamper, will open.
3. Open the service door and use acleaning brush to remove any dirt
from the channel. The dirt will fall into the coffee grounds container.
Clean the container as well.
4. When the ground coffee dispensing channel is clean, close the
service door and press the CLEAR GRINDER and ESPRESSO buttons
simultaneously. The cover of the ground coffee channel will close.
5. The
button will briefly blink, indicating that the machine is heating
up to operating temperature. Once the control panel lights up, the
coffee machine is ready to make another coffee.
Outer Surface of the Coffee Machine
To clean the outer surface of the appliance, use aclean, slightly damp
cloth. Then wipe everything thoroughly dry.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DESCALING
• Over time, minerals from the water can build up in the machine’sinner
circuit. This is anatural process. Therefore, regular descaling is
necessary. Mineral deposits can spoil the taste of your coffee.
• The coffee machine is equipped with abuilt-in counter that keeps
track of the number of prepared coffees, and once it reaches 500,
the descaling process should be performed. Insuch acase, the
AMERICANO andDOUBLE ESPRESSO buttons will start blinking at
the same time.
- 8 -
07/2025
2025, .
1. Fill the water tank with asolution of water and descaling agent.
Use Sencor descaling agent suitable for Espresso-type coffee
machines and follow the instructions given in the descaling
agent'saccompanying documentation.
2. Place abowl of at least 200 ml under the head.
3. Press andhold the AMERICANO andDOUBLE ESPRESSO buttons
simultaneously. The coffee machine will enter the descaling mode.
4. The descaling process takes about 10 minutes. The CLEAN, DOUBLE
ESPRESSO, ESPRESSO andAMERICANO control buttons will
flash gradually. Leave the coffee machine to complete the descaling
process.
5. Once the descaling process is complete, the buttons will turn off.
6. Remove the water tank and refill it with clean, cold water. Insert it
back into the coffee machine andactivate the manual rinsing process
repeatedly until the water tank is completely empty.
Storage
• If the appliance will not be used for an extended period, unplug it
from the power socket, let it cool down, and clean it following the
instructions provided above.
• Before storing, ensure that the appliance and all accessories are
thoroughly clean and dry.
• Store the appliance in adry, clean, and well-ventilated place away
from extreme temperatures and out of the reach of children or pets.
- 9 -
07/2025
2025, .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TROUBLESHOOTING
Problem Cause Solution
NO WATER indicator light is blinking.
Insufficient water in the tank. Refill the water tank.
The WARNING indicator light is blinking.
Incorrectly closed service door. Close the service door properly.
The WARNING indicator light is on.
Improperly inserted brewing unit; improperly
inserted coffee grounds container and drip tray.
Insert the brewing unit, coffee grounds container
and drip tray correctly.
The NO BEAN indicator light is on.
Insufficient coffee beans in the hopper. Add coffee beans to the hopper.
The CLEAR DREGS indicator light is on.
The coffee grounds container is full. Empty the coffee grounds container and inner tray.
The CLEAN BREWER indicator light
is on.
Brewing centre needs to be cleaned. Remove the brewing centre and clean it. Then,
reinsert it.
The ESPRESSO andWARNING buttons
are flashing simultaneously.
Ground coffee dispensing channel door drive does
not work properly.
Turn off the coffee machine and then turn it
on again. If the problem persists, contact your
authorised service centre.
The NO BEANS andWARNING indicator
lights are blinking simultaneously.
The coffee machine has ground coffee for
16cycles with each grinding time being less than
5 minutes.
Turn off the coffee machine and disconnect it from
the power source. Let it cool down for 5 minutes
and then you can use it again.
The CLEAN button and WARNING
indicator light are blinking
simultaneously.
The flow meter has no signal and the water
dispensing is abnormal.
Add water to the water tank.
The CLEAN andESPRESSO buttons
and the WARNING indicator light are
blinking simultaneously.
Hall sensor has no signal and brewing centre is not
functioning properly.
Turn off the coffee machine, wait for awhile, then
turn it on again.
Weak coffee froth. The ground coffee is too coarse. Turn the coarseness regulator clockwise to adjust
the grinder setting.
You are using unsuitable roasted coffee beans. Use roasted coffee beans specially for Espresso
machines.
Slow or dripping coffee flow. The ground coffee is too fine. Turn the coarseness regulator counterclockwise
and adjust the grinder setting.
The coffee machine is not dispensing
coffee.
The coffee spout is clogged. Clean the coffee spout, for example, using athin
object.
The coffee machine does not switch on. The plug is not inserted correctly into the power
socket.
Check the plug connection in the power socket.
The power cable is not inserted correctly in the
socket at the back of the coffee machine.
Check the power cable connection.
You have not pressed the button. Press the button to turn the coffee machine on.
CLEAR DREGS andCLEAN BREWER
are on.
Coffee grounds container needs to be emptied and
brewing centre needs to be cleaned.
Empty the coffee grounds container and clean the
brewing centre.
Wait about 3 seconds before reinstalling.
The CLEAN DREGS indicator light is
on, but the coffee grounds container
is empty.
The internal counter has not been reset after
emptying the container or cleaning the brewing
centre.
Always wait for about 3 seconds for the counter to
reset after emptying the coffee grounds container
or cleaning the brewing unit. Empty the coffee
grounds container and clean the brewing unit
whenever the coffee machine is turned on. If you
empty the container or clean the brewing unit while
the coffee machine is turned off, the counter will
not reset.
The grinder grinds but does not dispense
ground coffee.
Deeply roasted beans may have oil on their
surface. If the coffee beans are wet or have too
much oil on their surface, the ground coffee
dispensing channel will be blocked.
Press and hold the CLEAR GRINDER and
ESPRESSO buttons simultaneously for 2 seconds,
and they will start blinking.
Open the service door and remove the ground
coffee from the ground coffee dispensing channel
using abrush. Close the service door once the
ground coffee starts to fall freely.
Press and briefly hold the CLEAR GRINDER
andESPRESSO buttons simultaneously and they
will turn off.
The coffee machine is too noisy. It is normal for the coffee machine to make noise
during operation.
If the coffee machine starts to make adifferent kind
of noise, lubricate the brewing centre.
- 10 -
07/2025
2025, .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TECHNICAL SPECIFICATIONS
Rated voltage range ..............................................................................220–240 V~
Rated frequency ...................................................................................................50 Hz
Rated input power ............................................................................................. 1350W
Noise level .........................................................................................................70 dB(A)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Values provided according to Commission Regulation EU
2023/826
Off mode
Power consumption in off mode 0.5 W
Time needed for the equipment to automatically
reach off mode
28 min
Standby mode
Power consumption in Standby mode –
Time needed for the equipment to automatically
reach standby mode
–
Networked standby mode (Wi-Fi)
Power consumption in networked standby –
Time needed for the equipment to automatically
reach networked standby mode
–
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTRUCTIONS AND INFORMATION ON DISPOSAL
OF USED PACKAGING MATERIAL
Dispose of used packaging material at the designated municipal waste
disposal site.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DISPOSAL OF USED ELECTRICAL AND ELECTRONIC
EQUIPMENT
Used electrical andelectronic products must not be disposed of in
ordinary municipal waste. To enable the proper disposal, renewal and
recycling of these products, deliver them to the designated collection
points. Alternatively, in some European Union states or other European
countries the products can be returned to the local retailer when buying
an equivalent new product. By disposing of this product correctly, you
help to conserve valuable natural resources and prevent any potential
adverse impact on the environment and human health that could result
from improper waste disposal. For more details, contact your local
authority or nearest collection point. Fines may be imposed for the
improper disposal of this type of waste as per national regulations.
For business entities in European Union States
If you wish to dispose of electrical and electronic equipment, please
request the necessary information from your retailer or supplier.
Disposal in other countries outside the European Union
To dispose of this product elsewhere, request the necessary information
on the correct disposal method from local authorities or your retailer.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changes to text and technical parameters are reserved.
