VI
Ｌｏｃｋ ｃｕｒｒｅｎｔ ｃｈａｎｎｅｌ
Lock current channel: Press and hold "Channel+" or "Channel -
Power On" simultaneously while in the off state, and hear "beep"
to lock the current channel. Repeating again unlocks the
current channel
Ｐｒｅｓｓ ａｎｄ ｈｏｌｄ ｏｎｅ ｏｆ ｔｈｅ ｋｅｙｓ
PTT
PTT
PTT
PTT
PTT
TYPE-C charging port
Short press
PTT
Shut down on the twelfth channel. Simultaneously press
and hold the PTT key and "Channel+" or (Channel -)
Power on, can switch between Chinese and English
Ⅶ
PTT
ｓｅｌｅｃｔ
Ｏｎｅ ｏｆ ｔｈｅｍ
Ｓｉｍｕｌｔａｎｅｏｕｓｌｙ
ｈｏｌｄ ｄｏｗｎ
two way radio
TX/RX:400-480MHz
Power:2W
Nan'an Shi Hong Ying Electronic Science and
Technology Co., Ltd
Add:No.1145 Xiamei Village, Xiamei Town, Nan'an
City, Fujian Province, China
10
9
FCC Regulations
Federal Communication Commission (FCC) requires that all radio communication products should meet the
requirements set forth in the above standards before they can be marketed in the U.S, and the manufacturer shall post
a RF label on the product to inform users of operational instructions, so as to enhance their occupational health against
exposure to RF energy.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates and can radiate radio frequency energy. If not installed and used in accordance
with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. Verification of harmful interference by this equipment to radio or
television reception can be determined by turning it off and then on. The user is encouraged to try to correct the
interference by one or more of the following measures:
● Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a different circuit to that of the receiver's outlet.
● Consult the dealer or an experienced radio/TV technician for help.
Operation is subject to the following two conditions:
● This device may not cause harmful interference.
● This device must accept any interference received, including interference that may cause undesired operation.
Note: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
RF Exposure Compliance and Control Guidelines and Operating Instructions
To control your exposure and ensure compliance with the occupational/controlled environmental exposure limits,
always adhere to the
following procedures.
Guidelines:
● Do not remove the RF Exposure Label from the device.
● User awareness instructions should accompany device when transferred to other users.
● Do not use this device if the operational requirements described herein are not met.
Operating Instructions:
● Transmit no more than the rated duty factor of 75% of the time. To transmit (talk), press the Push-to-Talk (PTT) key.
To receive calls, release the PTT key. Transmitting 75% of the time, or less, is important because the radio generates
measurable RF energy only when transmitting (in terms of measuring for standards compliance).
● Keep the radio unit at least 2.5 cm away from the face. Keeping the radio at the proper distance is important as RF
exposure decreases with distance from the antenna. The antenna should be kept away from the face and eyes.
● When worn on the body, always place the radio in an approved holder, holster, case, or body harness or by use of
the correct clip for this product. Use of non-approved accessories may result in exposure levels which exceed the
FCC's occupational/controlled environmental RF exposure limits.
● Use of non-approved antennas, batteries, and accessories causes the radio to exceed the FCC RF exposure
guidelines.
● Contact your local dealer for the product's optional accessories.
