智能戒指快速使用指南
请使用包装盒内充电仓为戒指
充电，打开手机APP搜索连接
戒指后开始使用
首次使用前，请先阅读本指南
，并按照步骤完成充电、APP
下载与设备配对
扫码提示
请根据所在地区和手机系统选
择对应二维码扫码下载。
如二维码跳转至下载落地页，
请按页面提示选择对应版本。
使用说明
使用充电仓连接戒指进行充电。
首次使用前，请先为戒指充电至可开机
状态。
充电中充电仓指示灯红灯闪烁，充满后
充电仓指示灯熄灭
当戒指指示灯闪烁后，再打开 APP 搜
索并配对设备
附加说明
戒指充电时，可能无法被 APP 搜索或
完成配对。
如设备长时间未使用，请先充电后再开
机。
首次使用前，请先阅读本指南，并按照
步骤完成充电、APP 下载与设备配对
请充电时注意连接好戒指，连接充电成
功时戒指绿色长亮
连接 APP + 配对戒指连接UBlingAPP
1. 扫码下载并打开UBling APP。
2. 进入 APP 的“设备”页面。
3. 点击“添加设备”。
4. 点击“蓝牙搜索”，找到UBlingR1，
点击连接。
5. 按照页面提示完成配对。
配对前请确认
手机蓝牙已开启。
APP 已获得蓝牙权限和必要的设备权限。
戒指已充电，并已拔开充电线。
戒指靠近手机，避免距离过远导致搜索
失败,搜索不到设备时,如未搜索到戒指，
请先确认戒指电量是否充足，并重新进
入“添加设备”页面搜索。
如仍无法连接，可关闭并重新打开手机
蓝牙，或重启 APP 后再次尝试。
合规说明 + 使用提醒
使用提醒
当电量低于 5% 时，设备无法测量数据，请先充电后再使用。
请勿在充电状态下佩戴戒指或进行测量。
请勿用力弯折、撞击、拆解或自行维修设备。
请保持传感器区域清洁，避免污渍影响测量稳定性。
如长时间不使用，请先充电后再开机连接。
免责声明
本产品测量结果仅供日常参考，不用于任何医疗目的。
请勿将测量结果用于自我诊断或治疗。
如有身体不适，请及时咨询医生。
合规提示
本设备在正常使用过程中可能产生低功率无线信号。请按照说明书
要求使用设备，
并避免自行拆解或改装。
若设备对其他电子设备产生干扰，请尝试调整使用距离或停止使用
后联系售后。
用户电话：___________
产品保修卡
购买平台： 线上 官网 其他
订单号码：___________
产品颜色：___________
保固期限：一年送修
产品序号：___________
产品型号：___________
购买日期：___________
经销商：_____________
User Info:__________________
Warranty Card
Order No.:_________________
Product Configuration:________
Warranty: One Year Warranty
Service
Product Serial No.: ___________
Product Model: ______________
Purchase Date:______________
Dealer Name:_______________
插入USB线，给充
电仓充电，红灯长
亮，充满绿灯长亮
戒指充电时，充电
仓绿灯呼吸闪烁,
充电完成，充电仓
指示灯自动熄灭
充电仓低电10% 充
电仓灯红灯闪烁 1
秒一次
Quick Start Guide
Charge the ring with the included
charging case. Launch the mobile
APP, search and connect the ring to
begin use.
Read this guide prior to first use,
then finish charging, APP download
and device pairing step by step.
QR Code Prompt
Scan the appropriate QR code
for your region and mobile OS
to download.
If redirected to the download
landing page, select the
correct version as instructed
on the page.
Instructions for Use
Charge the ring by placing it in the charging case.
Before first use, charge the ring until it can power
on.
While charging, the indicator light on the charging
case flashes red.
Once fully charged, the charging case indicator
turns off.
After the ring’s indicator light starts flashing, open
the APP to search for and pair the device.
Additional Notes
The ring may not be found or paired by the APP
while it is charging.
If the device has not been used for a long time,
charge it before powering on.
Before first use, read this guide and complete
charging, APP download and device pairing
following the steps.
Ensure the ring is properly connected during
charging. The ring’s indicator stays solid green
when charging starts successfully.
Connect to APP & Pair the Ring
Connect the ring with UBling APP
1. Scan the QR code to download and open the
UBling APP.
2. Go to the **Device** page in the APP.
3. Tap **Add Device**.
4. Tap **Bluetooth Search**, locate UBlingR1 and tap
to connect.
5. Complete pairing following the on-screen prompts.
Before Pairing, Please Confirm
Bluetooth on your mobile phone is enabled.
The APP has been granted Bluetooth permission and
required device permissions.
The ring is charged and removed from charging.
Keep the ring close to your phone; excessive
distance may cause search failure.
If the Device Cannot Be Found
If the ring is not detected, check whether the ring has
sufficient power, then re-enter the "Add Device" page
to search again.
If connection still fails, turn your phone’s Bluetooth off
and on again, or restart the APP and retry.
Compliance Statement + Usage Reminders
Usage Reminders
When the battery level is below 5%, the device cannot take measurements. Please
charge it before use.
Do not wear the ring or perform measurements while it is charging.
Do not bend, strike, disassemble or attempt to repair the device by yourself.
Keep the sensor area clean to prevent stains from affecting measurement stability.
If the device will not be used for an extended period, charge it before powering on and
connecting.
Disclaimer
Measurement results from this product are for daily reference only and are not intended
for medical purposes.
Do not use the measurement results for self-diagnosis or treatment.
Consult a doctor promptly if you feel unwell.
Compliance Notice
This device may emit low-power wireless signals during normal operation. Use the
device in accordance with this manual.
Do not disassemble or modify the device on your own.
If the device causes interference with other electronic equipment, adjust the operating
distance or stop using it and contact after-sales support.
Plug in the USB
cable to charge
the charging case.
A solid red light
indicates charging;
it turns solid green
once fully charged
When charging the
ring, the charging case
indicator breathes in
green. Once charging
completes, the
charging case
indicator will turn off
automatically.
When the charging
case power is low
(10%), its indicator
flashes red once
every second
Light Status + Wearing Instructions
Light Status
Wearing Instructions
Wear the ring on a comfortable and
properly-fitted finger.
Index, middle or ring finger is
recommended.
Position the sensor against the
underside of your finger for
more stable data readings.
Do not wear it too loosely, as this may
cause unstable contact
between the sensor and skin.
Keep your hand steady during
measurement and avoid
vigorous shaking.
Data may fluctuate after exercise,
when your finger is wet,
or if the ring shifts position.
If readings are abnormal, reposition
the ring and retake
the measurement.
灯光状态 + 佩戴方式
灯光状态
佩戴方式
将戒指佩戴在舒适合适的手指上，
建议佩戴在食指、中指或无名指。
请将传感器贴近手指下方，以获得
更稳定的数据。
佩戴时不要过松，避免传感器与皮
肤接触不稳定。
测量时请保持手部稳定，避免剧烈
晃动。运动后、手指潮湿或
佩戴位置偏移时，数据可能出现波
动。如数据异常，
可调整佩戴位置后重新测量。
Charging – Ring
indicator flashes red.
Heart Rate
Measurement – Ring
indicator flashes green.
Charging Complete
– Ring indicator
shows solid green.
SpO2 Measurement
– Ring indicator
shows solid red.
充电中-戒指红
灯闪烁
心率测量-戒指
绿灯闪烁
充电完成-戒指
绿灯长亮
血氧测试-戒指
红灯长亮
