ES3
Specifications
Frequency Response: 20HZ-20KHZ
Impedance: 32 ohm
Sensitivity : 85土3 dB/mW
Working Range: 1 Om
Battery capacity: 3 00 mAh
Charging Time: = 2 H
Working Time: = 23 H
Rated Power : 10 mW
Largest Power : 15 mW
Speaker Diameter : 40mm
Button Function
"
�
1
"
P
o
w
e
r
o
n
/
P
o
w
e
r
o
“
十"Volume up: short press
Move next: long press
“
一
'
,
Volume down: short press
Move previous: long press
@＠
e
Function Description
1. Power on: Long press"
�1
"for more than 3 seconds,the
headphone turn on and enter Bluetooth Mode.The blue and
red lights flash alternately.
2. Power o: Long press" �1 "for more than 3 seconds,the
light is off and the headphone turn o.
Button Guide
1. Answer: short press"
H
I
" button when being called
2. Hang up: sho press"
H
I
"button when calling
3. Dial back: double click"
HI
" button.
4. Play music: normally short press" HI "button to turn on the
sma devices automatically to play music
5. Continue to play music aer the call: when there is an
incoming call, the music will be automatically suspended. Aer
the call, the music will continue playing
Bluetooth Pairing
-
Repairing: turn off the Bluetooth function of the connected
smart devices, at this lime, the Bluetooth headset and the last
matching device got disconnected,LED light flashed between
「ed and blue.and enter the Bluetooth pairing mode.then turn on
the Bluetooth function of the smart devices, search the device
named "E63" to get connected, aer pairing successfully, the
voice prompts "connected", the blue LED is on and flash slowly.
-
Subsequent pairing: 3 seconds after powering on, the
headphone will automatically search and connect the smart
device which paired last lime.
Other Functions
-
Warning voice of maximum volume: "Dudu"
-
Power saving mode: the headphone will automatically turn o
aer 5 minutes of no connection
-
TYPE-Cdlaing port, user friendly.
LED Indicator
Charging
I
red LED is on when charging, and blue LED is on
aer full charged
Pairing
I
Blue and red LED ashes alternately
NOTE:
This equipment has been tested and found to comply with the
limits for a Class B digital, pursuant to Part 15 or the FCC
Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and can 「adiate
radio frequency energy and, if not installed and used in
acco「dance with the instructions, may cause harmful
interference to radio communications, However, there is no
guarantee that interference will not occur in a particular
installation. If the equipment does cause harmful inteerence
to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try
to correct the inteerence by one or more of the following
measures:
---
Reorient or relocate the receiving antenna
---
Increase the separation between the equipment and
receiver.
---
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
---
Consult the dealer or an experienced radio/ TV technician
for help
70叮0mm双面印刷
Wireless
Headphone
GORS
U
N
FCC STATEMENT :
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
RF warning statement:
The device has been evaluated to meet general RF exposure
requirement. The device can be used in portable exposure condition
without restriction.
