Easy
Key
7000 series
DDL709-FVP-7HWS
Facial recognition
smart door lock
User
manual
Sign your product up and get
support at
www.philips.com/support
1
19
21
22
Contents
1. Important Information
2. Assembly
3. Get to know your
smart lock
Outside escutcheon
Inside escutcheon
Safety
Caution
Disposal of used products and
batteries
Packing list
Exploded views
Notice before assembling
Adjustable latch instructions
Assembly procedure
02
03
09
10
16
4. Settings
Instructions before setting
Master mode
User settings
Settings
Network settings
App binding guidance
Cloud Storage Usage Guide
5. Get to use your lock
Outdoor/ indoor unlock
Outdoor/ indoor lock
Inside deadlock
Mechanical key unlock
6. Other features
7. Indicators
Door lock status indicator
Low battery indicator
Outside forced lock indicator
Mute indicator
Indoor deadlock indicator
System locking indicator
8. Troubleshooting
Alert types
How to apply external power
supply
Battery replacement
Battery recharge
Indoor infrared unlock
Outside forced lock
Mute button
Default settings
Doorbell
Video intercom
Display
2
1. Important information
Safety
◆
Before using the product, please read through
and fully understand all instructions. The
warranty will not cover damage caused by non-
observance to the instructions.
◆
Suggest using only the manufacturer-specied
accessories / components.
◆
Use only the alkaline or Li-polymer batteries
the product is equipped with or use the same
type of batteries with the same specication.
◆
Do not forcibly disassemble the product
to avoid triggering the alert or damaging the
product.
◆
Do not use any sharp object to scratch the
ngerprint sensor, otherwise, it might cause
permanent damage.
◆
Do not expose products to places that have
water leakage or splashing.
◆
Do not expose the product to corrosive
substances to prevent damaging the protective
cover.
◆
Do not hang objects on the handle in case it
might aect the normal use of the lock.
◆
Please clean the product with soft cloth.
◆
Do not disassemble the battery during setting
up and operating.
◆
Please follow the assembly instructions that
we provided to install the product and keep the
relevant sealed stickers properly.
◆
Please modify the default master PIN code
immediately after installation and conguration
are done, and keep the mechanical key properly,
do not disclose the PIN codes to others.
◆
Please replace all the batteries in time if there
is a low battery alert. Please make sure to match
the poles (+/-) correctly when installing the
batteries.
Caution
◆
Do not place the batteries near ignition source
to avoid explosion.
◆
Do not use any power supply that does not
meet the safety requirements to power up the
product.
◆
Do not connect the 2 poles of the batteries
with metals to avoid short out which may lead to
explosion.
◆
Please make sure any component replacement
is executed by Philips, Philips authorized service
centers or professional technicians.
◆
Do not use accessories or parts that have been
produced by other manufacturers or have not
been specically recommended by Philips. The
use of such accessories and parts may void your
warranty.
Disposal of used
products and batteries
◆
You can have your locks reclaimed at Philips
authorized service centers. You will receive
corresponding compensation if your products
meet our recall conditions.
◆
Please familiarize with the local electronic
product collection system yourself.
◆
Please follow local regulations and do not
discard used products and batteries into ordinary
household waste.
◆
Please familiarize with the local regulations
on batteries classication recycling yourself.
Disposing of used products and batteries
properly can help avoid a negative impact on the
environment and human health.
3
① Outside
escutcheon with
silicon pad
② Inside
escutcheon with
silicon pad
③ Drilling
template
④ Mortise
⑤ Fixing plate ⑥ QSG ⑦ Warranty card ⑧ Certificate of
conformity
⑨ Key tag ⑩ Mechanical keys
⑪
Li-Polymer
battery
⑫
Strike plate
⑬
Installation kit
⑭
Charging cable
Warranty
Card
Easy
Key
EasyKey
合格证
Quick Start
Guide
EasyKey
Packing list
This packing list is for reference only. Please refer to the actual packing items.
2 Assembly
4
1 2 3 4
5 6 7 8 9 10
11
12
13
Exploded views
1. Battery cover*1
2. Li-polymer battery*1
3. M6 anchor screw*2
4. Inside escutcheon*1
5. Compressed spring*2
6. Square shaft*2
7. M5 anchor screw*2
8. Fixing plate*1
9. Mortise*1
10. M5 screw tube*2
11. M6 screw tube*2
12. Outside escutcheon*1
13. Screw plug*1
5
Left-hand swing Right-hand swing
Left-hand inswing
Left-hand outswing
Right-hand inswing
Right-hand outswing
Loosen the screws counterclockwise
with an Allen wrench and remove the
mortise plate.
Reattach the mortise plate on the
mortise and tighten the screws with
the Allen wrench.
Pull the latch straight out of mortise,
turn the latch 180 degrees, and
reinsert it into the mortise.
1
3
2
Notice before assembling
Adjustable latch instructions
This product applies to doors with four opening directions: left-hand inswing,
left-hand outswing, right-hand inswing, and right-hand outswing.
Attention
1. Choose a proper installation kit base on the door thickness.
2. The default tool kit applies to a door thickness of 60-90mm. Please consult the local distributor for other
door thicknesses.
Mortise plate
Latch
Mortise plate
Allen wrench
Allen wrench
6
1 2
3
4
Assembly procedure
The following assembly procedure applies to the right-hand swing doors. For
left-hand swing doors, please read through the [Notice before assembling] and
complete the adjustable latch instructions.
To drill holes in the door according
to the drilling template, mount the
mortise into the jamb, and tighten the
four anchor screws.
Pass the connecting cable through
the hole, align and insert the square
shaft of the outside escutcheon into
the rotary hole, so that the outside
escutcheon is tight against the outside
of the door.
Fasten the xing plate to the inner
surface of the door and use two M5
connecting screws to secure it tightly.
Attach the connecting screw tube on
the outside escutcheon and put the
compressed spring and square shaft in
the square shaft hole accordingly.
Attention Attention
Please make sure the dead bolt are retracted
during assembly.
Please choose the appropriate length of the
square shaft and screw tube according to the door
thickness.
M6 connecting
screw tube
M6 connecting
screw tube
Connecting cable
Mortise
connecting cable
Escutcheon
connecting cable
Antenna
M5 connecting
screw tube
Antenna
7
5 6
7 8
9
Put the compressed spring and
square shaft on the inside escutcheon
accordingly.
Open the upper
decorative cover and the
battery cover, mount,
and tighten the M6
anchor screws to secure
the inside escutcheon.
Check the rotary knob,
the mechanical key, and
whether each part is
connected and assembly
in good condition.
Install the battery and
put the battery cover
back, then mount the
upper decorative cover
and install the strike
plate to nish the
assembly.
Insert the escutcheon connecting cables
and mortise connecting cables into the
corresponding socket of the inside escutcheon,
then connect the antenna, and align the
square shaft hole on the inside escutcheon
against the rotary hole on the mortise, so that
the inside escutcheon is closely attached to the
inner surface of the door.
Mortise
connecting
cable
Socket of mortise
connecting cable
Socket of
escutcheon
connecting cable
Connecting
cable of outside
escutcheon
Antenna
Attention
Attention
Be sure to put the escutcheon connecting cables
and the mortise connecting cables into the slot on
both sides of the square shaft, and hide the extra
cables in the door hole or inside escutcheon.
After installing the strike plate, please test to see if the door opens and closes smoothly.
8
①
Camera
②
Indicator
③
Fingerprint sensor
④
Keypad
⑤
Mute button
⑥
Ultrasound sensor
⑦
Facial recognition
module
⑧
Push-pull handle
⑨
Doorbell button
⑩
Card reader
⑪
Low battery indicator
⑫
Reset and external power
supply interface
⑬
Mechanical key hole
①
Display
②
Battery compartment
③
Application
programming interface
④
Reset button
⑤
OPEN/CLOSE button
⑥
Rotary knob
⑦
Push-pull handle
7
4
3
1
6
2
5
This packing list is for reference only. Please refer to the actual packing items.
3 Get to know your smart lock
Outside escutcheon
Inside escutcheon
4
5
9
6
8
7
10
11
1
2
3
12
13
9
User
code
Name Fingerprint PIN code Key tag Face ID
00
01
02
03
04
05
06
07
08
Key tag
[#] key [*] key
Instructions before setting
◆ The system mode is divided into general mode and dual-verication mode.
4 Settings
General mode Any enrolled access methods can unlock the door
Any two enrolled access methods among PIN code, key tag,
ngerprint, and face ID can unlock the door
Dual verication mode
◆ User code
You can delete a user's information by its user code without having to delete everything.
You can record the user information in the following table for future queries.
Master
PIN code
One-time
PIN code
Face ID
User PIN
code
User code
00-99
Fingerprint
enrollment
Master
ngerprint
◆ Icon annotation
Attention
1. Press [*] key to return to the previous menu.
2. The default master PIN code is 12345678.
10
1
Add a user PIN code: Enter a new user
PIN code, and press【#】to conrm, then
re-enter the user PIN code and conrm
with【#】again. After the voice prompt
of “succeeded”, press [*] to back to the
previous menu until exit the master mode.
Add a user ngerprint: Place the nger on
the ngerprint sensor, and you will hear a
voice prompt of “please remove your nger
and place it on the sensor again”, take your
nger o and put it back again, repeat
several times until you hear a voice prompt
of “succeeded”, then press【*】to return to
the previous menu until you exit the master
mode.
Add a user key tag: Enroll a new key
tag, when you hear a voice prompt of
“succeeded”, press【*】to back to the
previous menu until you exit the master
mode.
1
Master mode User settings
Master PIN code
Add a user PIN code
Master ngerprint
After lighting up the keypad, press [*] twice
before entering other numbers, then enter
the master PIN code and conrm with [#],
then you are in master mode.
Press [*] twice, enter the master PIN code,
and then press [#] to conrm.
Press [1] to enter user settings, and then
press [1] to add a user, the door lock will
automatically recognize the corresponding
access method and add PIN codes,
ngerprints, and key tags directly.
After lighting up the keypad, press [*] twice
before entering other numbers, then place
your enrolled master ngerprint on the
ngerprint sensor to enter master mode.
Attention
Attention
If the master PIN code is the initial PIN code, you
will need to enter [1] and then [5] in the master
mode to modify the master PIN code before you
can perform other operations.
1. Please enroll a master ngerprint before using
the product.
2. Please do not set the master ngerprint and user
ngerprint with the same nger.
11
2
1
1
1
1
Add a one-time PIN code Add or change a master ngerprint
Modify master PIN code
Add a Face ID
Press [*] twice, enter the master PIN code,
and then press [#] to conrm.
Press [*] twice, enter the master PIN code,
and then press [#] to conrm.
Press [1] to enter user settings, then press
[4] to add or change a master ngerprint.
Press [1] to enter user settings, then press
[2] to add a one-time PIN code.
Press [*] twice, enter the master PIN code,
and then press [#] to conrm.
Press [*] twice, enter the master PIN code,
and then press [#] to conrm.
Press [1] to enter user settings, then press
[5] to modify master PIN code.
Press [1] to enter user settings, then press
[3] to add a Face ID.
Position your face in front of the camera
and gently move your head in dierent
angles by following the voice prompt. After
hearing a voice prompt of “succeeded',
press [*] until you nally exit the master
mode.
Enter a 6-12 digits one-time PIN code, and
press [#] to conrm; enter the one-time PIN
code again, and conrm with [#]. After the
voice prompts"added succeeded", press [*]
to return to the previous menu until you
exit the master mode.
With no enrolled master ngerprint:
Enroll a new user ngerprint, and the
new ngerprint will be set as the master
ngerprint. After a voice prompt of
“succeeded”, press [*] to back to the
previous menu until you exit the master
mode.
With existed master ngerprint : Enter
a new user ngerprint, and the new
ngerprint will cover the old master
ngerprint. After a voice prompt of
“succeeded”, press [*] to back to the
previous menu until you exit the master
mode.
12
1
Enter a new master PIN code and conrm
with [#]. Enter the new master PIN code
again and conrm with [#]. Once heard a
voice prompt of "succeeded", press [*] until
you exit master mode.
Press [*] twice, enter the master PIN code,
and then press [#] to conrm.
Press [*] twice, enter the master PIN code,
and then press [#] to conrm.
Press [2] to enter system settings, then press
[1] to enter language settings.
Press [*] twice, enter the master PIN code,
and then press [#] to conrm.
Press [2] to enter system settings, then press
[2] to enter volume settings.
Select the volume needed: press [1] for
higher volume; press [2] for lower volume;
press [3] for mute mode. After the setting is
done, press [*] to back to the previous menu
until you exit the master mode.
Select the language needed: for Chinese,
please press [1]; for English, please press
[2]. After the voice prompts "setting
succeeded", press [*] to return to the
previous menu until you exit the master
mode.
Press [1] to enter user settings, then press
[6] to delete user’s information.
Delete a user
Select the access methods that need to
delete: to delete a PIN code, please press [1];
to delete a ngerprint, please press [2]; to
delete a key tag, please press [3]; to delete a
Face ID, please press [4]; to delete all user's
information, please press [5], for the specic
access methods that need to delete, please
follow the voice prompt to operate. After
the voice prompts deletion succeeded,
press [*] to return to the previous menu
until you exit the master mode.
or or or or
or or
or
Settings
Language settings
Volume settings
Attention
Attention
The default language is English.
The default volume is higher volume.
13
Press [*] twice, enter the master PIN code,
and then press [#] to conrm.
Press [*] twice, enter the master PIN code,
and then press [#] to conrm.
Press [*] twice, enter the master PIN code,
and then press [#] to conrm.
Press [4] to enter network conguration
and it will exit the master mode
automatically once the conguration is
done.
Press [2] to enter system settings, then press
[5] to enable/disable the infrared handle.
After the voice prompts the operation is
done, press [*] until you exit the master
mode.
Press [2] to enter system settings, then press
[3] to enter Eco settings.
Press [*] twice, enter the master PIN code,
and then press [#] to conrm.
Press [2] to enter system settings, then
press [4] to enable/disable dual-verication
mode. After the voice prompts the
operation is done, press [*] until you exit
the master mode.
Press [1] to turn on/o video; press [2] to
turn on/o facial recognition; press [3] for
sensor settings. After the voice prompts the
operation is done, press [*] until you exit
the master mode.
or or
Network conguration
Eco settings Infrared handle
Dual-verication mode
Join a network
Attention
Attention
Attention
The Eco mode is disabled by default.
The infrared handle is enabled by default.
The default verication mode is general mode.
14
③
③
④
⑤
⑥
Go back to the APP and follow the
prompt to finish the binding process.
App binding guidance
Cloud Storage Usage
Guide
Download
Add a door lock
Scan QR code
Manually adding the device
①
①
②
②
Please scan the QR code below to
download Philips EasyKey Plus APP on
your phone.
Open the Philips Easykey Plus app
and go to the "All Devices" or "Smart
Lock" tab on the homepage. Select the
corresponding model of your smart door
lock.
Tap on the "Check it out" or "Learn
more" button on the cloud storage
introduction page to learn more.
Copy and paste the URL: https://easykey.
conex-global.com into your browser to
enter the store.
Click on the "PROTECT PLANS" in the
navigation bar to access the purchase
page and select a desired subscription
plan.
Follow the on-screen prompts to make
the payment. After the payment is
completed, check your order payment
information and activation QR code via
email.
Return to the homepage, tap on the "+"
icon in the top right corner and scan the
activation QR code. Select the device you
want to use the subscription plan with
and click "Conrm".
1. After powering up the door lock, nd
the QR code on the back of the battery
cover.
2. Open the "Philips EasyKey Plus" APP,
and click [Add a Device] on the home
page.
3. After scanning the QR code on the
battery cover, follow the instructions of
the APP to complete the binding process.
1. Enter the "Philips EasyKey Plus" APP,
and click [Add a device] on the home
page.
2. Search for the current door lock model
and enter the binding process.
3. Press [*] twice on the lock, enter
the master PIN code, and press [#]
to conrm, then the door lock will
be in master mode. Press [4] to "Join
a network", and the voice prompts
"binding, please wait".
Attention
The door lock only supports 2.4G band Wi-Fi
routers (5G band is not supported). Please ensure
the distance between the router and the door lock
is less than 10 meters, otherwise the Wi-Fi signal
might be weak.
Philips Cloud Storage Service allows you
to store real-time recorded videos from
the door lock in the cloud, which can be
accessed for playback anytime via the cloud.
Here’s a guide to help you understand and
make the most of cloud storage(need to
bind the door lock in the app rst):
15
1
① Touch to wake up
the keypad, enter
the enrolled PIN
code and conrm
with [#].
② After the voice
prompts " door
opened”, push or
pull the handle to
unlock the door.
① Place the enrolled
nger on the
ngerprint sensor.
② After the voice
prompts “door
opened”, push or
pull the handle to
unlock the door.
① Place the enrolled
key tag on the card
reader.
② After the voice
prompts “ door
opened”, push or
pull the handle to
unlock the door.
① Face the camera
with the enrolled
face ID.
② After the voice
prompts “ door
opened”, push or
pull the handle to
unlock the door.
Use the rotary knob to
unlock.
Double press the [OPEN]
button within one second,
and then push or pull the
door to unlock the door.
With the infrared sensor
on, once the sensor
detects the hand from the
handle's front and rear side,
touching the handle could
unlock the door.
Rotary knob OPEN button Infrared handle
PIN code
Fingerprint
Key tag
Face ID
1
1
1
2
2
2 2
Outdoor/ indoor unlock
5 Get to use your lock
Outdoor unlock
Indoor unlock
Keypad
Push/
pull to
unlock
Fingerprint
sensor
Card
reader
Push/pull
to unlock
Push/pull
to unlock
Push/pull
to unlock
Facial
recogni-
tion
module
16
Push knob
Outside/Inside locking
Inside deadlock
Mechanical key
After closing the door, the latch bolt will automatically pop up to lock, and there
will be a voice prompts "Door closed".
After the door is locked, long press the
[CLOSE] button, and there will be a voice
prompt of "Inside deadlock enabled".
1. In inside deadlock mode, all functionalities from the
outside escutcheon will be disabled. With any enrolled
access method input from the outside escutcheon,
the keypad will display the combination of “15937(X)”
followed by a voice prompt of “Inside deadlock
enabled” to remind you that the door has locked from
inside.
2. In the inside deadlocked mode, unlocking from the
outside can only be achieved by entering the master PIN
code or using the mechanical key.
Attention
① Cut the mechanical key
box and take out the key
shell. Push the knob aside
and reveal the key itself.
② Insert the key into the
key hole and keep the key
and key shell vertical to
each other. Rotate the key
shell towards the handle for
90° until it becomes close to
the door surface.
③ Rotate the key cell 180°
downward so it can be
parallel to the ground，then
rotate it horizontally
toward the lever to unlock
the lock.
Attention
Please use the mechanical key to unlock the door for emergencies only, i.e. when the battery is dead, when
you forgot the PIN code, or the lock fails to work.
17
Infrared sensor
Touch sensor
Function：
When this function is enabled, you
could unlock the door from inside.
How to use：
When the touch sensor and infrared
sensor are on, touching the touch
sensor and infrared sensor on the
handle can unlock the door.
Infrared handle:
When the infrared handle is o, long
pressing the [OPEN] and [CLOSE]
buttons for 10 seconds can enable the
infrared handle.
When the infrared handle is on, long
pressing the [OPEN] and [CLOSE]
buttons for 10 seconds can disable the
infrared handle.
Function:
Unlocking from inside will trigger
an alert.
How to use:
After the door is locked, press [8] to
enter the outside forced lock mode.
Functional button
Attention
Attention
When the infrared handle is o, you will not be
able to unlock the door from inside. When your
hand touches the touch sensor and the infrared
sensor, the red light will light up to remind you
that the infrared handle is o.
The outside forced lock mode will not aect the
normal unlocking from outside.
6 Other features
Indoor infrared unlock
Outside forced lock
18
Mute button
Default settings
Function:
Press [0] to enable mute mode
when before unlocking the door,
this function applies to scenarios
in which you don’t want to disturb
your family.
How to use:
Mute: when the outside escutcheon
is light up, press the [mute button]
for 2 seconds to enter mute mode,
it will follow by a voice prompt of
"mute mode enabled".
Unmute: when the outside
escutcheon is light up, press the
[mute button] for 2 seconds to
restore to voice guide, it will follow
by a voice prompt of "voice prompt
enabled".
Function:
To empty all user information and
restore to default settings.
How to use:
Double press the [RES] button with
a sharp object, and all the user
information will be emptied. The
lock will restore to default settings.
Mute button
19
Doorbell
Video intercom
Function:
The indoor speaker emits a ding-
dong sound to remind the host that
a visitor has arrived.
How to use:
Press the doorbell from outside, the
indoor speaker will emit a ding-
dong sound. Simultaneously, the
camera of the door lock will capture
the visitor's photo, and send the
captured content to the bond APP.
After the APP receives the push
message, you can remotely view the
captured content of the doorway
and unlock the door accordingly.
Function:
You can view the doorway situation
and realize real-time two-way
intercom via video function on the
APP.
How to use:
After the door lock bond to the APP,
you can view the doorway situation
and realize real-time two-way
intercom via video function.and
unlock the door accordingly.
Attention
After pressing the doorbell, the smile curve will
ash in blue.
20
Display
Function:
When the visitor rings the doorbell,
users can check the doorway from
the indoor display.
How to use:
1. When a visitor rings the doorbell,
the indoor display will be on. Click
the indoor screen button to turn on
the display, and you can also view
the doorway through the screen.
2. Users can set the display duration
and screen brightness via APP.
21
Status indicator
Low battery level
indicator
Outside forced
lock indicator
7 Indicators
Status indicator
Low battery level indicator
Outside forced lock indicator
Blue: When the system wakes up, the
indicator will turn blue, indicating that
the door lock can be processed and
operated;
Green: When the door lock is
unlocked, the indicator will turn green,
indicating that the door has opened;
Red: When the door lock is locked, the
indicator will turn red, indicating that
the door has closed.
Red: When the door lock system
wakes up, the battery voltage will be
automatically detected. If the voltage
is too low, the indicator will ash in
red. When the lock is unlocked, there
will be a voice prompt indicating that
the battery level is low, please replace
the battery in time.
White: When the door lock is locked,
the digit "8" lights up alone, indicating
that the outside forced lock mode can
be activated.
22
Digit “2” ashes Digit “1” ashes
Within 2 mins Within 1 min
Indoor deadlock indicator
System-locking indicator
In indoor deadlock mode, the digital
functions of the outside escutcheon
will be disabled. After waking up that
system manually, the keypad will show
the combination of “15937 (X)”, and
follow by a voice prompt indicating
that the inside deadlock is enabled.
The door lock will be locked
for 100 seconds if there are 5
consecutive incorrect inputs
among any of the 3 types of
access methods(ngerprint,
PIN code, or key tag ) within
5 minutes.
Attention
Only when touching to wake up
the keypad or verifying the access
methods will the system appears such
a system-locking prompt.
23
Low battery alert
Anti-dismantling alert
Triggering: If the lock is under outside
forced lock mode, unlocking from inside will
trigger the alert.
Alert mode: Continuously repeated alert.
Off: The alert will be off by any access
verification method.
Triggering: When the system wakes up,
the battery voltage will be automatically
detected. If the battery voltage is
insufficient, an alert will be triggered to
remind you to replace the battery.
Alert mode: A voice prompt of “Low
battery, please replace the battery” during
unlocking.
Off: The alert will turn off automatically.
Triggering 1: The door is pried open, and
the sensor latch bolt pops up.
Alert mode: Continuously repeated alert.
Off: The alert will be off automatically or off
after a successful access verification.
Triggering 2: Outside escutcheon is pried
open, and there is no fit to the door.
Alert mode: Continuously repeated alert.
Off: Auto-close, or close after a successful
access verification, or close after unlocking
from inside.
8 Troubleshooting
Alert types
Outside forced lock mode
24
Deadbolt abnormality alert
Motion detection alert
Ultrasound
sensor
Triggering: If the deadbolt works
abnormally, the door fails to lock or unlock.
Alert mode: Continuously repeated alert.
Off: The alert will be automatically off.
Triggering: When a suspicious person
is loitering around at the front door for
a period that exceeds the set value, the
loitering alert will be triggered.
Alert mode: The camera will capture a video
by default and send a notification to the
APP.
Off: Motion detection is off by default, if
you need to use this feature, you can enable
or disable it on the APP.
Attention
1. The motion detection alert is o by default. To enable this feature, please log in to the APP, bind the
door lock on home page. Once the binding process is done, go to "Settings" and turn on "loitering alert".
2. The more the video function used, the faster the power consumption will be. To reduce the detection
frequency and battery consumption, it is suggested to set the motion detection sensitivity level to "Low".
25
How to apply an external power supply
Battery replacement
Battery recharge
Reset & External power
supply interface
When the battery voltage is
insucient, and the door cannot
open from outside, you can power
up the lock through a 5V power
bank as an external power supply.
After opening the door lock, please
replace the batteries immediately.
In case of a system crash and it’s
unable to open the door from outside,
please use an external power supply
to power up the door lock, then it can
be rebooted automatically.
The working power of the door lock
is a 5000mA/h Li-polymer battery.
The battery compartment locates
at the upper end of the inside
escutcheon. You can slide the
battery cover upwards and remove
the cover to replace the battery.
Remove the battery from the door
lock and charge it via a charging
cable.
Attention
1. The warranty period for the Li-polymer
battery is 1 year.
2. The charging voltage is 5V.
3. When the network condition is unstable, it
will accelerate the battery aging.
Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V.
and are used under license. This product has been manufactured by and is sold under the
responsibility of Shenzhen Conex Intelligent Technology Co., Ltd. and Shenzhen Conex
Intelligent Technology Co., Ltd. is the warrantor concerning this product.
