C363, C363DT, C563, C763,
C563DT, C383, C583, C783
In-Ceiling Architectural
Loudspeaker
Instruction Manual
2
In-Ceiling Architectural Loudspeaker
Instruction Manual
About Revel
®
in-ceiling SpeAkeRS
Since the first Revel
®
speakers in 1996, Revel products have stood at
the forefront of loudspeaker design and performance. Revel in-ceiling
loudspeakers draw upon the same research, resources and unique
perspective that put all Revel loudspeakers in a class by themselves.
Revel in-ceiling loudspeakers provide unparalleled value and are known
for their standard-setting low sonic coloration and their freedom from
distortion over an extraordinarily wide dynamic range.
in-ceiling loudSpeAkeR HigHligHtS
• Long-throw woofers with cast frames and rubber surrounds provide
high output with low distortion.
• 1-inch (25mm) angle-adjustable, metal-dome tweeter with an
integrated waveguide provides optimized response both on and off
axis.
• High-order crossover network with premium-quality components
delivers extraordinarily accurate timbre reproduction.
• Boundary compensation switch (C783/C763) lets you adjust the
speaker to maintain tonal accuracy when the speaker is placed near
a wall.
• Three-position tweeter level control (C783/C763/C583/C563)
lets you adjust for optimum response in a variety of acoustical
environments, or for using the speakers without grilles.
pRoduct RegiStRAtion
Please take a moment to register your product on our Web site at www.
revelspeakers.com. You’ll enable us to keep you posted on our latest
advancements and help us to understand our customers and build
products that meet their needs and expectations.
box contentS
Your Revel in-ceiling loudspeaker box should contain the following
items:
1 x Revel in-ceiling loudspeaker
1 x round grille
1 x square grille
1 x extra scrim cloth for round grille
1 x extra scrim cloth for square grille (with attached foam pads)
1 x mounting template
1 x instruction manual
unpAcking tHe SpeAkeR
Carefully unpack the speaker. If you suspect damage from transit, report
it immediately to your dealer and/or delivery service. Keep the shipping
carton and packing materials for future use.
inStAllAtion conSideRAtionS
Your new Revel loudspeakers have been engineered to provide
extremely accurate performance. However, any speaker’s ultimate
performance will be affected by the speaker’s placement in the listening
room and the acoustics of the room. Not all listening spaces can
accommodate the ideal conditions of these two factors. Therefore,
careful attention to the placement of your Revel in-ceiling loudspeakers
will have a significant impact on the general performance of the
loudspeakers.
documentAtion conventionS
This document contains general safety, installation and operation
instructions for the Revel
®
C783, C583, C383, C763, C563, C363,
C563DT, C363DT in-ceiling loudspeakers. It is important to read
this document before attempting to use this product. Pay particular
attention to:
WARNING: Calls attention to a procedure,
practice, condition or the like that, if not
correctly performed or adhered to, could result
in injury or death.
CAUTION: Calls attention to a procedure, practice,
condition or the like that, if not correctly performed or
adhered to, could result in damage to or destruction of part
of or the entire product.
Note: Calls attention to information that aids in the
installation or operation of the product.
3
In-Ceiling Architectural Loudspeaker
Instruction Manual
loudSpeAkeR plAcement foR diStRibuted
Sound
• Since distributed sound is general sound throughout an area, place
the loudspeakers as uniformly as possible for even sound coverage
throughout the area.
• Place the left and right loudspeakers roughly the same distance
from the primary listener locations.
• To avoid “hot spots” where the sound is too loud, plan to use more
loudspeakers, with each set to play at a lower volume.
loudSpeAkeR plAcement foR two-cHAnnel
SteReo
Place the left and right loudspeakers the same distance from the
primary listening area (or as close to the same distance as possible). The
distance from each speaker to its nearest side wall should also be the
as close to the same distance as possible.
Boundary
Compensation
High Frequency
Level
OFFON
0+–
Boundary
Compensation
High Frequency
Level
OFFON
0+–
Equal
Distance
Equal
Distance
RightLeft
Ideally, the distance between the left and right loudspeakers should be
slightly less than their distance from the primary listening area.
loudSpeAkeR plAcement foR Home tHeAteR
• The front left, center and front right loudspeakers should be
centered relative to the video display.
• The front left, center, and front right loudspeakers should be closer
to the video display than to the main listening area. For example,
if the video display is 10 ft (3m) from the main listening area, the
loudspeakers should be 6 ft (1.8m) or further from the main listening
area.
• The front left and front right loudspeakers should be relatively close
to the sides of the video display. For example, front left and front
right loudspeakers used with a 50-in (1.2m) video display should
generally not be more than 80 in (2m) apart.
• The center loudspeaker should be aligned with the center of the
video display.
• The surround-channel loudspeakers should be as far from the main
listening area as possible but at least 2 feet (0.6m) from side and
rear walls.
5.1-Channel Speaker Placement
• In a 5.1-channel system, the surround left and surround right
loudspeakers should be located to the sides of, and approximately
10 degrees behind, the main listening area.
Boundary
Compensation
High Frequency
Level
OFFON
0+–
Boundary
Compensation
High Frequency
Level
OFFON
0+–
Boundary
Compensation
High Frequency
Level
OFFON
0+–
Boundary
Compensation
High Frequency
Level
OFFON
0+–
Boundary
Compensation
High Frequency
Level
OFFON
0+–
Front Left
Surround Left
More than
2' (0.6m)
More than
2' (0.6m)
Surround Right
Approx. 10
°
Center Front Right
Video Display
7.1-Channel Speaker Placement
• In a 7.1-channel system, the surround left and surround right
loudspeakers should be located directly to the sides of, or up to 10
degrees behind, the main listening area.
• In a 7.1-channel system, the surround back left and surround back
right loudspeakers should be equidistant from the primary listening
area and generally as far from it as possible but at least 2 ft (0.6m)
from the side and rear walls.
Boundary
Compensation
High Frequency
Level
OFFON
0+–
Boundary
Compensation
High Frequency
Level
OFFON
0+–
Boundary
Compensation
High Frequency
Level
OFFON
0+–
Boundary
Compensation
High Frequency
Level
OFFON
0+–
Boundary
Compensation
High Frequency
Level
OFFON
0+–
Boundary
Compensation
High Frequency
Level
OFFON
0+–
Boundary
Compensation
High Frequency
Level
OFFON
0+–
Front Left
Surround Left
Surround
Back Left
Surround
Back Right
More than
2' (0.6m)
More than
2' (0.6m)
More than
2' (0.6m)
Surround Right
0
°
–
10
°
Center Front Right
Video Display
4
In-Ceiling Architectural Loudspeaker
Instruction Manual
loudSpeAkeR plAcement foR duAl-tweeteR
SteReo modelS
Because a single Revel dual-tweeter stereo in-ceiling speaker
reproduces both stereo channels from a single location, it will deliver
outstanding performance from a wide variety of mounting locations
where a pair of stereo speakers would be impractical, including
hallways, bathrooms and closets.
inStAllAtion inStRuctionS
CAUTION: Do not use the tweeter-mounting baffle as a handle
to move, carry or position the speaker. Doing so can damage the
baffle. Such damage is not covered by the speaker’s warranty.
Revel architectural speakers are extremely easy to install. However, if
you are unable to understand and follow the instructions in this manual
clearly and fully, or if you are unsure of your ability to install these
loudspeakers properly, please contact your dealer or a qualified installer.
WARNING: HARMAN International assumes
no responsibility for improper installation of
hardware or for any personal injuries or product
damages resulting from improper installation or
a fallen loudspeaker.
connecting to tHe AmplifieR
CAUTION: REMOVE POWER
You must connect the speaker wires before the speaker is fully
installed. To protect the audio system and yourself from damage
or injury through accidental electrical shorting and surges
during installation, turn all audio system power OFF before
beginning the speaker installation.
Speaker Wire
Use high-quality speaker wire to obtain the best performance from your
Revel in-ceiling speakers.
• For wire lengths of less than 50 ft (15m), use at least 16-gauge
speaker wire.
• For wire lengths between 50 ft and 100 ft (15m – 30m), use at least
12-gauge speaker wire.
• For wire lengths of greater than 100 ft (30m), use at least 10-gauge
speaker wire.
Note: All speaker wires must comply with all local building and
safety codes for use in in-ceiling applications.
Making Connections
Connect each channel’s positive (+) terminal on the back of the amplifier
or receiver to the positive (“IN+”/red) terminal on the corresponding
speaker; connect each channel’s negative (–) terminal on the back of
the amplifier or receiver to the negative (“IN–”/black) terminal on the
corresponding speaker. Do not reverse polarities (that is, do not connect
+ to –, or – to +) when making connections. Doing so will cause poor
imaging and diminished bass response.
Negative Terminal
(“IN–”/Black)
Positive Terminal
(“IN+”/Red)
Press down on the top of the terminal to open the hole; insert the bare
end of the wire into the hole; and release the terminal to secure the wire.
CAUTION: To avoid short circuits that may damage your
equipment, be certain that positive and negative wire strands do
not touch each other and do not touch metal parts such as the
speaker frame.
5
In-Ceiling Architectural Loudspeaker
Instruction Manual
mounting tHe SpeAkeRS
For New Construction
If you wish to pre-install a rough-in frame for the speakers before the
drywall is installed in new construction, you will need to purchase
the correct rough-in frame kit for your loudspeaker model from your
authorized Revel dealer. Detailed mounting instructions are supplied
with the rough-in kit. After the drywall is installed, follow the
installation instructions in For Existing Construction, below.
For Existing Construction
Note: The installation procedure is the same for all models
covered by this manual.
1. Ensure that the drywall, plywood or other ceiling material is 1/2" –
2" (13mm – 51mm) thick and capable of withstanding the weight of
the speaker being installed.
Make sure to allow at least 3/4" (19mm) between the edge of the
supplied installation template and any rafters or other obstructions
behind the wall, so the speaker’s locking mechanism will have room to
engage fully. Perform an obstruction survey to be sure that there are
no studs, lengths of conduit, pipes, heating ducts or air returns in the
ceiling cavity that will interfere with the speaker.
Mounting
Opening
3/4"
(19mm)
3/4"
(19mm)
3/4"
(19mm)
2. Determine the correct speaker location and use the template included
with the speaker to mark the ceiling material.
3. Cut the ceiling drywall along the mark you made in Step 2 to create
the mounting opening.
4. Connect the speaker to the amplifier as explained in Connecting to the
Amplifier, on page 4.
5. Attach the speaker's seismic tab to a support line, as per local safety
regulations.
Seismic Tab
Support Line
6. Make sure all four speaker clamps are in their “ready-to-mount”
position.
C2 Speaker Clamps in
Ready-to-Mount Position
6
In-Ceiling Architectural Loudspeaker
Instruction Manual
7. Insert the speaker straight into the mounting opening. Tighten the
speaker clamp screws on the front of the speaker baffle. The speaker
clamps will automatically rotate into position and begin clamping the
speaker.
• When you notice resistance on the screws the speaker has been
clamped successfully.
IMPORTANT: Always use low-torque settings. NEVER
over-tighten the clamp screws
Insert Speaker Straight Into
Mounting Cut-Out
Tighten
Clamping Screws
C2 Speaker Clamps Inside
Mounting Cut-Out
8. Attach the supplied round or square grille. Powerful magnets in the
speaker frame will securely hold the grille in place.
Attach Supplied Grille
Painting the Grille
Revel architectural loudspeaker grilles can be painted to match any
décor. If you wish to change the grille’s color, its satin finish will function
as a primer coat. For the best results follow this procedure:
1. Gently remove the scrim cloth from the back side of the grille before
painting.
2. Use a high-quality spray paint and apply a thin coat of color. Ensure
that the grille perforations remain free of paint. Filling them with
paint will diminish the speaker’s sound quality. If any perforations are
plugged, use compressed air to blow the paint out of the perforations.
Note: If you find any grille perforations that are plugged with paint
after the paint has dried, carefully use a straight pin or sewing
needle to remove the paint.
3. We have included round and rectangular replacement scrim cloths.
After the paint has dried, apply a light coat of spray adhesive to
the inside of the perforated grille and attach a new scrim cloth.
IMPORTANT: Never spray adhesive on the cloth. The square scrim
cloth has pre-attached foam pads that help prevent the grille from
vibrating against the ceiling.
uSing YouR SpeAkeRS
AdjuStmentS
Adjustable Angle Tweeter (C783/C763/C583/C563/C383/C363)
Most Revel in-ceiling speaker models allow you to adjust the angle of
the tweeter. To change the angle, press on the tweeter’s outer ring as
shown in the illustration below. Be careful not to touch the tweeter
diaphragm or suspension.
Boundary Compensation Control (C783/C763)
The Boundary Compensation control reduces the speaker’s bass output
level to compensate for the greater reflection of bass energy when the
speaker is placed near a wall.
When possible, avoid mounting the speaker within 2 ft (0.6m) of a
wall. If such placement is unavoidable, set the Boundary Compensation
control to the “On” position.
Boundary
Compensation
High Frequency
Level
OFF ON
0+–
High-
Frequency
Level Control
Boundary
Compensation
Control
7
In-Ceiling Architectural Loudspeaker
Instruction Manual
High-Frequency Level Control (C783/C763/C583/C563)
The High-Frequency Level control lets you fine-tune the speaker’s high-
frequency output to compensate for various acoustical environments.
The control has three settings:
+: Increases high-frequency output. Set the switch to this position
if the room has many features that absorb high-frequency sound energy,
such as thick carpeting, drapes and fabric-covered furniture.
0: Normal high-frequency output. Set the switch to this position for
most installations.
–: Decreases high-frequency output. Set the switch to this position
if the room has many features that reflect high-frequency sound energy,
such as large uncovered windows, bare tile floors and large expanses of
bare walls, or if the speakers are used without grilles.
exceSSive output levelS
Your Revel loudspeakers feature custom-designed transducers and
high-quality network components featuring high-order filters with steep
cutoffs that reduce the potential of damage to individual speaker drivers
and help the loudspeakers maintain their performance even under
extreme operating conditions. However, all loudspeakers have limits
when it comes to continuous playback. To extend these limits, avoid
playback at volume levels that result in distorted or strained sound.
obtAining SeRvice
To obtain service, contact an authorized Revel dealer. Refer to Limited
Warranty, below for more information.
dimenSionS
Mounting Opening Diameter Mounting Depth Overall Dimensions (w/grille)
C783
9-7/8" (251mm) 5-15/32" (139mm) Deep 10-23/32" (272mm) Dia. X 5-5/16" (136mm) Deep
C583
9-7/8" (251mm) 5-15/32" (139mm) Deep 10-23/32" (272mm) Dia. X 5-5/16" (136mm) Deep
C383
9-7/8" (251mm) 5-15/32" (139mm) Deep 10-23/32" (272mm) Dia. X 5-5/16" (136mm) Deep
C763
8-1/4" (210mm) 4-5/8" (118mm) Deep 9-3/32" (231mm) Dia. X 4-25/32" (121mm) Deep
C563
8-1/4" (210mm) 4-5/8" (118mm) Deep 9-3/32" (231mm) Dia. X 4-25/32" (121mm) Deep
C363
8-1/4" (210mm) 4-5/8" (118mm) Deep 9-3/32" (231mm) Dia. X 4-25/32" (121mm) Deep
C563DT
8-1/4" (210mm) 4-5/8" (118mm) Deep 9-3/32" (231mm) Dia. X 4-25/32" (121mm) Deep
C363DT
8-1/4" (210mm) 4-5/8" (118mm) Deep 9-3/32" (231mm) Dia. X 4-25/32" (121mm) Deep
Dimensions are subject to change without notice.
For complete performance specifications, please go to the Revel Web
site: www.revelspeakers.com.
limited wARRAntY
A valid serial number is required for warranty coverage. This Revel
warranty protects the original retail purchaser for a period of five
(5) years (parts and labor) from any failure as a result of original
manufacturing defects so long as:
1. The Revel products were purchased within the 50 United States, its
territories or Canada.
2. The dealer from whom the Revel products were purchased was
authorized to sell such products at the time of the original purchase.
3. The original, dated Bill of Sale is presented whenever service is
required during the warranty period.
The balance of this warranty is transferable only if the used product is
purchased from an authorized Revel dealer. This warranty is only valid
for service within the United States, its territories and Canada; please
contact an authorized Revel dealer for warranty and service information.
Any Revel product not performing satisfactorily may be returned to
the factory for evaluation. Return authorization must first be obtained
by either calling or writing Customer Service prior to shipping the
product. The customer is responsible for shipping charges to the
factory. Customer Service will pay return shipping charges within the
United States only in the event that the product is found to be defective
as mentioned above. There are other stipulations that may apply to
shipping charges.
There is no other express warranty on this product. Neither this
warranty nor any other warranty, express or implied, including implied
warranties of merchantability and fitness, shall extend beyond the
warranty period. No responsibility is assumed for any incidental or
consequential damages, so that the above exclusion or limitation may
not apply.
This warranty provides specific legal rights. Other states may provide
additional rights. This warranty is applicable in the United States, its
territories and Canada. Outside of the United States, its territories and
Canada, please contact an authorized Revel dealer for warranty and
service information.
The information this document contains is subject to change without
notice. In the event that there are differences between this warranty
and the provisions of any advertisements, documentation, product
brochures or packaging cartons, the terms of this warranty will prevail.
www.revelspeakers.com
© 2012 HARMAN International Industries, Incorporated
All rights reserved.
Revel and the Revel logo are trademarks of HARMAN International
Industries, Incorporated, registered in the United States and/or
other countries.
Features, specifications and appearance are subject to change
without notice.
For questions, assistance or additional information concerning any
of our products, call us at: (516) 594-0300 or (888) 691-4171.
For technical support, submit your detailed inquiry to:
Part No. REVP4441 Rev.: 0
