
www.parrotuncle.com
English
F3010

Sicherheit information
1. To reduce the risk of an electrical blow, electricity on the
2. All wiring must correspond to the NASI/NFPA 70-1999
approved electrician.
3.
assembled safely and 35 pounds (15.9 kilos) must be able
to transport reliably. Use only output boxes listed with
labeling
"Accepted for fans with a weight of £ 35 (15.9 kilos) or less."
4. The fan must be installed with a minimum distance of 2.1 m
(7 feet) from the posterior edge of the blades to the floor.
5. Do not operate the reverse switch if the fan blades are
moving. You have to turn off the fan and stop the blades
6. Do not place objects on the road to blades.
7. To avoid lesions or damage to the fan and other objects, be
careful if you work on the fan or clean it.
8.
rates that are not delivered with the fan must be listed and
marked with the valve model that will be installed for use.
The switches must be general use switches UL. Take into
9.
staircase must be turned up and carefully push to the plug
box. The cables must be distributed in such a way that the
ground connected driver and the device head are next to
the socket.
necessary, followed.
WARNING: To reduce the risk of injury, blade brackets
cannot be folded during
Do not put any object on the path of blades.
WARNING:
Remove rubber motor
at the
of the fan before the blades or try
the motor.
WARNING: To avoid the risk of a fire or an
electrical blow, this fan should not be used with a
semiconductor speed controller.
WARNING: To avoid a possible electric shock,
turn off the current in the main security box
before wiring. If you feel that you do not have
enough knowledge or experience in electrical
wiring, communicate with a license electrician.
WARNING: Electrical diagrams only serve as a
be on the list and marked with this fan for use.
WARNING: To reduce the risk of fires, electrical
discharges or injuries, assemble the device in a
with a weight of £ 35) or less. It is marked and use
the screws supplied with the plug.
TECHNICAL INFORMATION
SKU
Nominal voltage
17W
15W 3000/4000/5000K, dimmable
Nominal output (motor) light
Installation & Operating Instructions for the
Parrot uncle Owner's Installation ,Manual
WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
F3010
Make sure that there is a space of at least 30 cm between the
fan’s blades and any wall or other obstacle with which they
could collide.It is important to note that the greater the
distance,the more efficient the airflow would be.
0,3m
1
110-120V ACF3010

Installation & Operating Instructions for the
Parrot uncle Owner's Installation ,Manual
WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
F3010
Mounting screw(2PCS)
Washer(2PCS)
Plastic wire nut (3PCS)
Remote control (1 PC)
1 2 4 8
Fan-motor assembly
Moun�ng plate

Installation & Operating Instructions for the
Parrot uncle Owner's Installation ,Manual
WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
F3010
1
Warning:Failure to disconnect power supply prior to installa�on may result in serious injury.
For safety and best opera�ng results,recommend you have a qualified
electrician install this fan.
Secure moun�ng plate to outlet box by �ghtening moun�ng screws & washers.
The ceiling fan must be installed in a loca�on with a minimum of 300mm spacing from the �p of
the blade to the nearest objects or walls.Secure the moun�ng plate to the ceiling joist or
structure that is capable of carrying a load of at least 15.9kgs,with two long screws provided.
Ensure at least 30mm of the screws is threaded into the support.
Note:For ease of wiring feed house wires through moun�ng plate.
Moun�ng screws
2
Moun�ng plate
100%(completely) remove 2 screws from the moun�ng plate
for later use.
70% remove 2 screws from the moun�ng plate.
3
FROM POWER SOURCE
AC 110- 120 VOLT 60Hz
3.5AMPS.
supplied with the
Use plastic wire nuts
fan
White
Hang the hole of the motor cover into
the hook of moun�ng plate.
Install whole fan to moun�ng plate with 4 screws.
WARNING: To avoid possible electrical shock,
be sure electricity is turned off at the main
fuse box before wiring.
Make the wire connec�on between the Fan
and power supply.Make sure all connec�ons
are secured.
Ground wire
100%
70%
X2
X2
And then take down the moun�ng plate.
L
N
Black
MOTOR
X4
4

Installation & Operating Instructions for the
Parrot uncle Owner's Installation ,Manual
WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
Remote controller
GENERAL INFORMATION
1.INSTALLING RECEIVER IN CEILING FAN
A. Safety precautions:
electrical code requirements.
B. Electrical rating: 110/120V 50/60Hz
Electrical wire must meet all local and national
Otherwise power can cause serious injury or death.
F3010
FAN ON/OFF & Paring
- Within 5 seconds after power on,
hold press 3 seconds to match code
Forward and Reverse
- Press to change Forward/Reverse
- Within 5 seconds after power on,
hold press 3 seconds to clear code.
Light Switch & CCT Setting
- Press to turn light ON/OFF
- Hold press 2 seconds to change CCT
Timer Settings
- Press once, fan auto off after 1hr
- Press twice, fan auto off after 2hr
- Press 3 times, fan auto off after 4hr
- Press 4 times, fan auto off after 8hr
- Press 5 times,Cancel the timer function
LED Indicator
Time setting Indicator
Speed setting Indicator
Fan speed 1 to 6 levels
Fan speed 6 to 1 levels
1 2 4 8
Light brightness +
Light brightness -
2. OPE RATI NG TRAN SMITTER :
A. Instal l CR2032 3 volt ba ttery.
(To prev ent da mag e to tran smitter , remov e the batter y if not us ed for a long time).
B. Stor e the tran smitter away from exces sive he at or humidi ty.
C. Operat ing the bu ttons on the pa nel of the transmitter .
- Press to turn Fan ON/OFF

Installation & Operating Instructions for the
Parrot uncle Owner's Installation ,Manual
WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
F3010
21in
7.7in
8.7in
Ø21in

AFTER INSTALLATION
The fan blades have been adjusted in the factory to minimize any wobble
NOTE:CEILING FANS TEND TO MOVE DURING OPERATION DUE TO THE FACT THAT THEY
ARE MOUNTED ON A RUBBER CROMMET. IF THE FAN WAS MOUNTED RIGIDLY TO THE
CEILING, IT WOULD CAUSE EXCESS VIBRATION. MOVEMENT OF A FEW CENTIMENTERS
IS QUITE ACCEPTABLE AND DOES NOT SUGGEST ANY PROBLEM
WOBBLE”
TO REDUCE THE FAN WOBBLE: PLEASE CHECK THAT ALL SCREWS WHICH SECURED THE MOUNTING
BRACKET AND DOWNROD ARE SECURE.
BALANCING A WOBBLING CEILING FAN:
1.Check that all blade and blade arm screws are secure.
2.Mos
t fan wobbling problems are caused when blade levels are unequal. Check this level by
selecting a point on the ceiling above the tip of one of the
blades. Measure this distance.Rotate the fan until the next blade is positioned for
measurement. Repeat for each blade. The distance deviation should be equal within
1/8"(0.32cm).
3.If the blade wobble is still noticeable, interchanging two
adjacent (side by side) blades can redistribute the weight
and possibly result in smoother operation. WARNING: TO REDUCE THE RISK OF PERSONAL
INJURY, DO NOT BEND THE BLADE ARM WHILE INSTALLING, BALANCING THE BLADES, OR
CLEANING THE FAN. DO NOT INSERT FOREIGN OBJECTS BETWEEN ROTATING FAN BLADES.
NOISE
When it is quiet(especially at night) you may hear occasional small noises. This is normal. Please allow a 24-
hour “breaking-in” period, most noises associated with a new fan disappear during the time.
CARE AND CLEANING
1.Periodic cleaning of your ceiling fan is the only maintenance required. Use a soft brush or lint free cloth to
avoid scratching the paint finish. Please make sure to turn off electricity power before you clean your fan
2.Do not use water when cleaning your ceiling fan. It could damage the motor or the blades
and create the possibility of an electrical shock.
3.Motor has permanently lubricated ball bearing. No need to oil
NOTE: MAKE SURE THE POWER IS OFF AT THE ELECTRICAL PANEL BOX BEFORE YOU
ATTEMPT ANY CLEANING OR REPAIRS.
Installation & Operating Instructions for the
Parrot uncle Owner's Installation ,Manual
WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
F3010

Pot Uncle
