TRIBUTE 4-IN-1 CHARGING CABLE WITH WATCH CHARGER
INSTRUCTION MANUAL
EAC-TB24
READ ALL INSTRUCTIONS CAREFULLY BEFORE USE.
SAFETY PRECAUTIONS
• This product is NOT a toy, keep away from children and pets.
• Only use the device according to the instructions in this manual. Never
use the device for anything other than its intended purpose.
• Do not open this device or attempt to repair the unit yourself if it is not
working properly. Doing so risks fire, shock or injury.
• When not in use, the device should be stored in a dry, cool location,
away from sources of water or heat.
• Do not expose device or charging cable to extreme temperatures (heat
or cold), open flames, humid or wet conditions.
• Do not submerge in water. Do not use in a location where the device
or charging cable could fall into liquid.
• Unplug the charging cable when not in use. Do not pull the charging
cable to disconnect, or use the cable as a handle.
• Do not use if device or charging cable is damaged. If device or
charging cable is damaged, it MUST be serviced or replaced by the
manufacturer or its service agent before using again.
• Attachments on the back of your device can impede effectiveness of
the wireless charger, and lead to overheating. Remove attachments
from your device before charging on this wireless charger.
PRODUCT DIAGRAMS
WIRELESS CHARGING INSTRUCTIONS
• Plug the input tip into a USB or USB-C power source, such as the USB
or USB-C port on a computer or into a certified USB/USB-C adapter
(not included), and plug into a wall socket.
• Place a wireless charging enabled smart watch on the watch wireless,
the watch will begin to charge automatically.
• There will be charging indication on the display of the charged watch.
• If your watch does not begin to charge, try repositioning your watch
on the wireless charging surface. You may need to remove the case of
your watch to charge properly.
• Remove your watch from the wireless charging surface when it is fully
charged.
CHARGING CABLE INSTRUCTIONS
• Plug the input tip into a USB or USB-C power source, such as the USB
or USB-C port on a computer or into a certified USB/USB-C adapter
(not included), and plug into a wall socket.
• Connect the output cable to your device with the appropriate tip.
• Your device will begin to charge.
• Remove the cable from your device when it is fully charged.
TECH SPECIFICATIONS
• Power Input: DC 5V/2A
• Wireless Charging Output: 2W
• Cable Peak Output Current: 2A
• Charging Distance: no more than 3mm
• Working Temperature: 14°F ~ 122°F (-10°C ~ 50°C)
FCC INFORMATION
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may
cause undesired operation.
NOTE 1: This equipment has been tested and found to comply with the
NOTE 2: Any changes or modifications to this unit not expressly
approved by the party responsible for compliance could void the user's
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
authority to operate the equipment.
FCC ID: 2BVZB-AD1869
RF Exposure Statement
To maintain compliance with FCC'S RF Exposure guidelines, This
equipment should be installed and operated with minimum 20cm
between the radiator and your body. This device and its antenna(s) must
not be co-located or operation in conjunction with any other antenna or
transmitter.
Made in China
