Visit our website at: http://www.harborfreight.com
email our technical support at: [email protected]
24702E-B
9"
BENCHTOP
BANDSAW
70630
Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference. 23k
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright
©
2023 by Harbor Freight Tools
®
. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
read this material before using this product.
Failure to do so can result in serious injury.
SaVe tHiS ManuaL.
Page 2 For technical questions, please call 1-888-866-5797. 70630
SaFety OperatiOn MaintenanceSetup
table of contents
Safety ......................................................... 2
Specifications ............................................. 6
Setup .......................................................... 6
Operation .................................................... 8
Maintenance .............................................. 11
Parts List and Diagram .............................. 14
Warranty .................................................... 16
WarninG SyMBOLS anD DeFinitiOnS
This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messages that
follow this symbol to avoid possible injury or death.
Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
Addresses practices not related to personal injury.
iMpOrtant SaFety inFOrMatiOn
General tool Safety Warnings
read all safety warnings and instructions.
Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
1. KEEP GUARDS IN PLACE and in working order.
2. REMOVE ADJUSTING KEYS AND
WRENCHES. Form habit of checking to
see that keys and adjusting wrenches are
removed from tool before turning it on.
3. KEEP WORK AREA CLEAN.
Cluttered areas and benches invite accidents.
4. DON’T USE IN DANGEROUS ENVIRONMENT.
Don’t use power tools in damp or wet locations,
or expose them to rain. Keep work area well lighted.
5. KEEP CHILDREN AWAY. All visitors should
be kept safe distance from work area.
6. MAKE WORKSHOP KID PROOF with padlocks,
master switches, or by removing starter keys.
7. DON’T FORCE TOOL. It will do the job better
and safer at the rate for which it was designed.
8. USE RIGHT TOOL. Don’t force tool or attachment
to do a job for which it was not designed.
Page 3For technical questions, please call 1-888-866-5797.70630
SaFetyOperatiOnMaintenance Setup
table a: recOMMenDeD MiniMuM Wire GauGe
FOr eXtenSiOn cOrDS
(120 VOLt)
naMepLate
aMpereS
(at full load)
eXtenSiOn cOrD
LenGtH
25′ 50′ 100′ 150′
0 – 6 18 16 16 14
6.1 – 10 18 16 14 12
10.1 – 12 16 16 14 12
12.1 – 16 14 12 Do not use.
9. USE PROPER EXTENSION CORD. Make sure your
extension cord is in good condition. When using
an extension cord, be sure to use one heavy
enough to carry the current your product will draw.
An undersized cord will cause a drop in line voltage
resulting in loss of power and overheating.
Table A shows the correct size to use depending
on cord length and nameplate ampere rating.
If in doubt, use the next heavier gauge.
The smaller the gauge number, the heavier the cord.
10. WEAR PROPER APPAREL. Do not wear
loose clothing, gloves, neckties, rings, bracelets,
or other jewelry which may get caught in moving
parts. Nonslip footwear is recommended.
Wear protective hair covering to contain long hair.
11. ALWAYS USE SAFETY GLASSES. Also use
face or dust mask if cutting operation is dusty.
Everyday eyeglasses only have impact resistant
lenses, they are NOT safety glasses.
12. SECURE WORK. Use clamps or a vise to
hold work when practical. It’s safer than using your
hand and it frees both hands to operate tool.
13. DON’T OVERREACH.
Keep proper footing and balance at all times.
14. MAINTAIN TOOLS WITH CARE. Keep
tools sharp and clean for best and safest
performance. Follow instructions for
lubricating and changing accessories.
15. DISCONNECT TOOLS before servicing;
when changing accessories, such as
blades, bits, cutters, and the like.
16. REDUCE THE RISK OF UNINTENTIONAL
STARTING. Make sure switch is in
off position before plugging in.
17. USE RECOMMENDED ACCESSORIES.
Consult the owner’s manual for recommended
accessories. The use of improper accessories
may cause risk of injury to persons.
18. NEVER STAND ON TOOL.
Serious injury could occur if the tool is tipped or
if the cutting tool is unintentionally contacted.
19. CHECK DAMAGED PARTS. Before further use
of the tool, a guard or other part that is damaged
should be carefully checked to determine that
it will operate properly and perform its intended
function – check for alignment of moving parts,
binding of moving parts, breakage of parts,
mounting, and any other conditions that may
affect its operation. A guard or other part that is
damaged should be properly repaired or replaced.
20. DIRECTION OF FEED.
Feed work into a blade or cutter against the
direction of rotation of the blade or cutter only.
21. NEVER LEAVE TOOL RUNNING UNATTENDED.
TURN POWER OFF. Don’t leave tool
until it comes to a complete stop.
Page 4 For technical questions, please call 1-888-866-5797. 70630
SaFety OperatiOn MaintenanceSetup
Grounding instructions
tO preVent eLectric SHOcK anD DeatH FrOM incOrrect
GrOunDinG Wire cOnnectiOn reaD anD FOLLOW tHeSe inStructiOnS:
110-120 Vac Grounded tools: tools with three prong plugs
1. In the event of a malfunction or breakdown,
grounding provides a path of least resistance for
electric current to reduce the risk of electric shock.
This tool is equipped with an electric cord having an
equipment-grounding conductor and a grounding
plug. The plug must be plugged into a matching
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
2. Do not modify the plug provided – if it will
not fit the outlet, have the proper outlet
installed by a qualified electrician.
3. Improper connection of the equipment-grounding
conductor can result in a risk of electric shock.
The conductor with insulation having an outer
surface that is green with or without yellow
stripes is the equipment-grounding conductor.
If repair or replacement of the electric cord or
plug is necessary, do not connect the equipment-
grounding conductor to a live terminal.
4. Check with a qualified electrician or service
personnel if the grounding instructions are
not completely understood, or if in doubt as
to whether the tool is properly grounded.
5. Use only 3-wire extension cords that
have 3-prong grounding plugs and 3-pole
receptacles that accept the tool’s plug.
6. Repair or replace damaged or
worn cord immediately.
Grounding
pin
125 Vac 3-prong plug and Outlet
(for up to 125 Vac and up to 15 a)
7. This tool is intended for use on a circuit that has
an outlet that looks like the one illustrated above in
125 Vac 3-prong plug and Outlet. The tool has
a grounding plug that looks like the plug illustrated
above in 125 Vac 3-prong plug and Outlet.
8. The outlet must be properly installed and grounded
in accordance with all codes and ordinances.
9. Do not use an adapter to connect
this tool to a different outlet.
Band Saw Safety Warnings
For your Own Safety read instruction
Manual Before Operating Saw
1. Wear eye protection.
2. Do not remove jammed cutoff pieces
until blade has stopped.
3. Maintain proper adjustment of blade tension,
blade guides, and thrust bearings.
4. Adjust upper guide to just clear workpiece.
5. Hold workpiece firmly against table.
6. Use special care when unpacking or
replacing bandsaw blade. Blade can be
under tension and may suddenly uncoil.
Wear ANSI-approved safety glasses under a
full face shield and heavy-duty work gloves.
7. DO nOt Operate WitH any GuarD
DiSaBLeD, DaMaGeD, Or reMOVeD. Moving
guards must move freely and close instantly.
8. The use of accessories or attachments not
recommended by the manufacturer may
result in a risk of injury to persons.
9. When servicing use only identical replacement parts.
10. Only use safety equipment that has been approved
by an appropriate standards agency. Unapproved
safety equipment may not provide adequate
protection. Eye protection must be ANSI-approved
and breathing protection must be NIOSH-approved
for the specific hazards in the work area.
Page 5For technical questions, please call 1-888-866-5797.70630
SaFetyOperatiOnMaintenance Setup
11. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or medication.
A moment of inattention while operating power
tools may result in serious personal injury.
12. Industrial applications must follow OSHA guidelines.
13. Maintain labels and nameplates on the tool.
These carry important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.
14. Avoid unintentional starting.
Prepare to begin work before turning on the tool.
15. People with pacemakers should consult their
physician(s) before use. Electromagnetic fields in
close proximity to heart pacemaker could cause
pacemaker interference or pacemaker failure.
16. The warnings, precautions, and instructions
discussed in this instruction manual cannot cover all
possible conditions and situations that may occur.
It must be understood by the operator that
common sense and caution are factors
which cannot be built into this product,
but must be supplied by the operator.
Vibration Safety
This tool vibrates during use. Repeated or
long-term exposure to vibration may cause
temporary or permanent physical injury,
particularly to the hands, arms and shoulders.
To reduce the risk of vibration-related injury:
1. Anyone using vibrating tools regularly or for an
extended period should first be examined by a
doctor and then have regular medical check-ups
to ensure medical problems are not being caused
or worsened from use. Pregnant women or
people who have impaired blood circulation to
the hand, past hand injuries, nervous system
disorders, diabetes, or Raynaud’s Disease should
not use this tool. If you feel any medical or
physical symptoms related to vibration (such as
tingling, numbness, and white or blue fingers),
seek medical advice as soon as possible.
2. Do not smoke during use. Nicotine reduces
the blood supply to the hands and fingers,
increasing the risk of vibration-related injury.
3. Use tools with the lowest vibration when there
is a choice between different processes.
4. Include vibration-free periods each day of work.
5. Grip workpiece as lightly as possible (while still
keeping safe control of it). Let the tool do the work.
6. To reduce vibration, maintain the tool as
explained in this manual. If any abnormal
vibration occurs, stop use immediately.
SaVe tHeSe inStructiOnS.
Page 6 For technical questions, please call 1-888-866-5797. 70630
SaFety OperatiOn MaintenanceSetup
Specifications
Electrical Rating 120VAC / 60Hz / 2.8A
Blade Speed 2500 FPM
Throat Depth 9 in.
Blade Length 59-1/2 in.
Blade Width 1/8 - 3/8"
Blade Size (included) 1/4"
Setup - Before use:
read the entire iMpOrtant SaFety inFOrMatiOn section at the beginning of this
manual including all text under subheadings therein before set up or use of this product.
tO preVent SeriOuS inJury FrOM acciDentaL OperatiOn:
turn the power Switch of the tool off and unplug the tool from its electrical outlet
before performing any procedure in this section.
note: For additional information regarding the parts listed in the following pages,
refer to the Assembly Diagram near the end of this manual.
assembly/Mounting
1. This tool must be mounted to a level,
stable bench or table before use.
2. If the mounting surface does not have predrilled
holes that match the four holes in the Base (47) of
the Band Saw, four 3/8″ holes will have to be drilled.
3. cautiOn! When drilling, check for
electric wiring or cables that may be in
the path of the hole(s) being drilled.
4. Secure the Band Saw to the surface
by using 3/8″ bolts, 3/8″ washers and
3/8″ hex-nuts (not included).
assembly
1. Unpack the Table (122) and remove
the protective cover.
2. Slide the slot in the Table around the Blade (9) and
position the Table onto the frame of the Base.
table
Slot
Blade
3. Pull out and release the Tilt Knob (89)
to help align the Table.
4. Secure the Table by installing two Table
Lock Knobs (97) and two Flat Washers
(73) through the Tilt Rack (80). Leave the
Lock Knobs slightly loose for now.
tilt Knob
tilt rack
5. Use a square (sold separately) to set Table
perpendicular (90° angle) to Blade and tighten
the Tilt Lock to secure the Table in place.
6. Loosen the Tilt Indicator Screw (57) and turn the
Tilt Indicator (82) around to face the scale.
7. Align the Tilt Indicator to 0° on the scale, and
hold it still while tightening the Indicator Screw.
8. Insert Bolt (78) into end of table slot, and
secure from below with Wing Nut (79),
Spring Washer (3) and Flat Washer (73).
Page 7For technical questions, please call 1-888-866-5797.70630
SaFetyOperatiOnMaintenance Setup
Functions
Blade tension
Lever
upper Housing Knob
power
Switch
Guide Fence
table
Lower Housing
Knob
Base
Blade tracking Knob
Motor
Dust port
Guide Height Knob
Blade Guide
Lock Knob
tilt Knob
table Lock Knobs
Blade
Page 8 For technical questions, please call 1-888-866-5797. 70630
SaFety OperatiOn MaintenanceSetup
Operating instructions
read the entire iMpOrtant SaFety inFOrMatiOn section at the beginning of this
manual including all text under subheadings therein before set up or use of this product.
tool Set up
tO preVent SeriOuS inJury FrOM acciDentaL OperatiOn:
turn the power Switch of the tool off and unplug the tool from its electrical outlet
before performing any procedure in this section.
tO preVent SeriOuS inJury:
DO nOt Operate WitH any GuarD DiSaBLeD, DaMaGeD, Or reMOVeD.
Moving guards must move freely and close instantly.
Blade Selection
Band Saw blade selection depends on the type of material to be cut,
the size of the workpiece and the type of cut desired:
1. The blade width is the distance from the tip of a
tooth to the back of the blade. Wider blades are
more rigid, wander less and provide a straighter cut.
Narrower blades handle curved cuts better.
2. The blade thickness is the distance between the
two sides of a blade. A thicker blade is more rigid
and has stronger teeth. A narrow blade is used
to make long, straight cuts with less waste.
3. The blade pitch describes the number of teeth
per inch (TPI). The more TPI, the smoother
(and usually slower) the cut. The type of
material being cut determines the blade pitch.
For soft materials the correct blade should
have 6-8 TPI. If hard materials are being cut,
use a blade with 8-12 TPI for best results.
note: There must be at least 3 teeth in contact
with the material
1
to prevent “blade shocking”.
This happens when the blade pitch is too large and
a blade tooth contacts too much of the workpiece.
This may strip teeth from the saw blade.
note: The included blade is
1/4″ wide x 0.01″ thick x 6 TPI.
1
TPI must be at least 3 divided by material
thickness in inches to prevent blade shocking.
Blade adjustment controls
tension Lever (120)
1. Raise Tension Lever (120) to initiate a
tension release. With the Lever raised,
rotate clockwise for more blade tension and
counterclockwise for less blade tension. Push
down Tension Lever to tension blade.
2. Wear heavy-duty work gloves, then open the
Upper Wheel Cover (8) and press the Blade on the
center of a span to check the tension. The Blade
should deflect slightly with finger pressure when
tensioned properly. Close the Upper Wheel Cover.
tracking Knob (88)
1. Switch off the Band Saw, unplug it, and
make sure that the Blade is properly
tensioned. Open the Upper Wheel Cover.
2. Check tracking by rotating Upper Blade
Wheel (13) by hand in a clockwise direction.
View Blade through Tracking Window (6).
3. Proper tracking is achieved when Blade runs
centered on the wheel. Minor adjustments
can be made using Tracking Knob (88).
4. As the Upper Blade Wheel rotates, if the
Blade moves away from the Tracking Knob,
turn the Tracking Knob slightly clockwise.
If it moves toward the Knob, turn the
Tracking Knob slightly counterclockwise.
5. Close the Upper Wheel Cover.
Page 9For technical questions, please call 1-888-866-5797.70630
SaFetyOperatiOnMaintenance Setup
Blade Guide alignment
1. The Blade Guide Assemblies support the Blade at
the rear and sides. They feature Guide Bearings,
which are located on both sides of saw blade and
provide a stable position for the blade when saw
is being used. The distance from guide bearings
to blade can be adjusted for optimal performance.
The guide bearings should not touch the blade
when a workpiece is not in contact with the blade.
Thrust bearings are located behind saw
blade and provide support to back of
blade when saw is in operation.
note: Adjust guide bearings only after the Blade has
been properly tensioned, and is tracking correctly.
2. Disconnect saw from its power source.
3. Adjust the Upper Blade Guides (110) by loosening
the lower Socket Head Screw (41) and sliding
the entire guide bracket until front of bearings
are positioned just behind the blade gullets.
Socket Head
Screws
Blade
cover
thrust Bearing
Set Screw
eccentric
Shaft
Guide
Bearing
4. Retighten lower Socket Head Screw.
5. Loosen set screw.
6. Use flat blade screwdriver (not provided)
to turn Eccentric Shaft until guide bearing
is almost touching saw blade.
7. Tighten set screw.
8. Repeat for opposite guide bearing.
9. Adjust Thrust Bearing (38) by loosening upper
Socket Head Screw and shifting bearing forward
until it almost touches back edge of blade.
10. Retighten upper Socket Head Screw.
11. Repeat Steps 3-10 for lower Blade Guide Assembly.
Workpiece and Work area Set up
1. Designate a work area that is clean and well-lit.
The work area must not allow access by children
or pets to prevent distraction and injury.
2. Route the power cord along a safe route to reach
the work area without creating a tripping hazard or
exposing the power cord to possible damage. The
power cord must reach the work area with enough
extra length to allow free movement while working.
3. Secure loose workpieces using a vise or clamps
(not included) to prevent movement while working.
4. There must not be objects, such as utility lines,
nearby that will present a hazard while working.
5. Long workpieces that extend beyond the
table should be properly supported.
Page 10 For technical questions, please call 1-888-866-5797. 70630
SaFety OperatiOn MaintenanceSetup
General Operating instructions
tO preVent SeriOuS inJury FrOM entanGLeMent:
Keep hands clear of Blade at all times and do not wear gloves when sawing.
note: the blade is not tensioned during
shipment to prevent damage. it must be
properly tensioned and tracked before use. See
Blade adjustment controls on page 8.
1. types of cut
a. Standard cuts are at 90° angle to the Table.
Use a push stick to guide the workpiece
through the Saw Blade.
b. contour cuts are accomplished by guiding
the workpiece free-handed for curve shapes.
When using this guiding method, use both
hands to follow the desired path and keep
the workpiece flat against the Table. Stand in
front of the Table and use both hands over the
part of the Table to the right of the Blade.
c. Bevel cuts are when the saw Table is tilted and
proper work guide methods are used. Unlock the
Table by loosening the Lock Knobs (97). Tilt Table
to correct angle using the Tilt Knob (89). When
correct angle is achieved, tighten the Lock Knobs.
2. Adjust the height of the Upper Blade Guide (110)
to barely clear the workpiece.
Loosen the Guide Lock Knob (96). Turn the
Guide Height Knob to adjust the Guide height.
Tighten Guide Lock Knob after adjusting.
3. This Band Saw is designed for cutting hard
and soft woods and most plastics. It is
equipped with a Miter Gauge Scale (74) used
to secure the workpiece at a desired angle to
produce angle cuts. Use the built-in Scale to
adjust the Miter Gauge to the required angle.
4. The Miter Gauge (74) is used to secure the
workpiece when crosscutting, or to make angle
cuts. Use the built-in Scale to adjust the Miter
Gauge to the required angle. Tighten knob
before using. Use one hand to securely hold
workpiece to Miter Gauge, while using other
hand to push Miter Gauge past blade.
5. The Fence (101) is used for rip cutting - making
a lengthwise cut through the workpiece. Release
Clamp (104) and place Fence on table to left of
blade. Align cut mark on workpiece with blade,
and slide Fence up against workpiece. Push
down Clamp to secure Fence. Push workpiece
against Fence while sliding it through blade.
Warning! to prevent serious injury: Do
not use Miter Gauge and Fence at the
same time, or binding may occur.
6. Turn on Band Saw using Switch and allow it to
reach full speed before beginning to saw.
7. Use two hands and hold workpiece
securely against table at all times.
8. Use push-sticks, or blocks (when required) to
move workpiece through the Blade. Use a smooth,
steady action to feed work through the blade.
9. Make sure the workpiece feeds against
the toothed side of the Blade.
10. To prevent accidents, turn off the tool and
disconnect its power supply after use. Clean, then
store the tool indoors out of children’s reach.
Page 11For technical questions, please call 1-888-866-5797.70630
SaFetyOperatiOnMaintenance Setup
Maintenance and Servicing
procedures not specifically explained in this manual must
be performed only by a qualified technician.
tO preVent SeriOuS inJury FrOM acciDentaL OperatiOn:
turn the power Switch of the tool off and unplug the tool from its electrical outlet
before performing any procedure in this section.
tO preVent SeriOuS inJury FrOM tOOL FaiLure:
Do not use damaged equipment. if abnormal noise or vibration
occurs, have the problem corrected before further use.
cleaning, Maintenance, and Lubrication
1. BeFOre eacH uSe, inspect the general
condition of the tool. Check for:
• loose hardware,
• misalignment or binding of moving parts,
• cracked or broken parts,
• damaged electrical wiring, and
• any other condition that may
affect its safe operation.
2. Do not allow saw dust to accumulate
on or in Band Saw.
3. Keep the Wheels clean. Debris on Wheels will
cause poor tracking and possible Blade slippage.
4. Keep mechanisms and sliding surfaces
clean and free of debris.
5. Shielded Ball Bearings do not need
lubrication. Small amounts of lightweight
machine oil can be applied to belt tension
mechanisms and sliding surfaces.
6. Paste wax can be applied occasionally to
Table Top (8) to keep it slick and corrosion free.
7. aFter uSe, wipe external surfaces
of the tool with clean cloth.
8. If storing for a long period, release tension
on the Blade by raising the Blade Tension
Lever. The blade’s tension and tracking will
need to be adjusted after thus storing.
9. Periodically, wear ANSI-approved
safety goggles and NIOSH-approved
breathing protection and blow dust out of
the motor vents using dry compressed air.
10. Clear all saw dust from Dust Tube (69) at base of
Band Saw. Do not let dust accumulate. Use a shop
vacuum (not provided) attached as a dust collector
when possible, and attach it to the Dust Tube (69).
Occasionally, vacuum out entire Band Saw.
11. cautiOn! if power tool is
damaged, it must be replaced only by
a qualified service technician.
12. Remove Safety Key from power switch and
store in a safe place, when saw is not in use.
Key must be inserted for saw operation.
replacing/installing Band Saw Blade
1. Turn the Power Switch (42) to its OFF
position and unplug the Power Cord (50).
2. Wear ANSI-approved safety goggles and
heavy-duty work gloves while handling the Blade.
3. Unlatch and open Upper Wheel Cover (8) and
Lower Wheel Cover (1), exposing the Saw
Blade and the Upper and Lower Wheels (9,13).
4. Raise Tension Lever, remove Bolt from
table slot, and remove old blade.
5. Hold open the Blade Guide Cover (34)
while installing the saw blade. Point the
blade’s teeth down towards Table, as shown
on the label on the Blade Guide Cover.
Turn the new blade inside out if necessary.
6. Slide new blade through slot and Table Insert, and
over Upper and Lower Wheels (13). Slide new blade
between upper and lower Blade Guide Bearings.
7. Close Upper and Lower Wheel Covers
and fasten latches. Make sure that both
doors and frames are fitted together before
attempting to secure. This is necessary for
proper operation of dust collection system.
8. Adjust tension and track Saw Blade as described
in Blade Adjustment Controls on page 8.
Page 12 For technical questions, please call 1-888-866-5797. 70630
SaFety OperatiOn MaintenanceSetup
troubleshooting
problem possible causes Likely Solutions
Tool will not start. 1. Cord not connected.
2. No power at outlet.
3. Tool’s thermal reset breaker
tripped (if equipped).
4. Internal damage or wear. (Carbon
brushes or switch, for example.)
1. Check that cord is plugged in.
2. Check power at outlet. If outlet is unpowered,
turn off tool and check circuit breaker.
If breaker is tripped, make sure circuit is right
capacity for tool and circuit has no other loads.
3. Turn off tool and allow to cool.
Press reset button on tool.
4. Have technician service tool.
Tool operates
slowly.
Extension cord too long or
wire size too small.
Eliminate use of extension cord. If an extension cord
is needed, use one with the proper diameter for its
length and load. See table a on page 3.
Performance
decreases
over time.
1. Accessory dull or damaged.
2. Carbon brushes worn or damaged.
1. Keep cutting accessories sharp.
Replace as needed.
2. Have qualified technician replace brushes.
Excessive noise
or rattling.
Internal damage or wear. (Carbon
brushes or bearings, for example.)
Have technician service tool.
Overheating. 1. Forcing machine to work too fast.
2. Accessory dull or damaged.
3. Blocked motor housing vents.
4. Motor being strained by long or
small diameter extension cord.
1. Allow machine to work at its own rate.
2. Keep cutting accessories sharp.
Replace as needed.
3. Wear ANSI-approved safety goggles and
NIOSH-approved dust mask/respirator while
blowing dust out of motor using compressed air.
4. Eliminate use of extension cord.
If an extension cord is needed, use one with
the proper diameter for its length and load.
See table a on page 3.
Follow all safety precautions whenever diagnosing or servicing the tool.
Disconnect power supply before service.
Page 13For technical questions, please call 1-888-866-5797.70630
SaFetyOperatiOnMaintenance Setup
record product’s Serial number Here:
note: If product has no serial number, record month and year of purchase instead.
note: Some parts are listed and shown for illustration purposes only, and are not available
individually as replacement parts. Specify UPC 193175502704 when ordering parts.
pLeaSe reaD tHe FOLLOWinG careFuLLy
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE
ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Page 14 For technical questions, please call 1-888-866-5797. 70630
SaFety OperatiOn MaintenanceSetup
part Description Qty
1 Lower Wheel Cover 1
2 Hex Socket Screw 2
3 Spring Washer 3
4 Non-Metallic Insert Nut 5
5 Phillips Screw 4
6 Tracking Window 1
7 Nut,Type I 2
8 Upper Wheel Cover 1
9 Blade 1
10 Clip For Shaft 2
11 Bearing 4
12 Hole Circlip 4
13 Wheel 2
14 Rubber Tire 2
15 Upper Wheel Shaft 1
16 Phillips Screw Assy 3
17 Idler Pulley 1
18 Nut 1
19 Spring Washer 1
20 Lower Wheel Shaft 1
21 Dome Screw 1
22 Brush 1
23 Upper Wheel Base 1
24 Spring Washer 1
25 Nut,Type I 1
26 U Bracket 1
27 Split Washer 2
28 Coupling Shaft 1
29 Blade Guide 1
30 Upper Guide Slider 1
31 Slide Plate 1
32 Phillips Tapping Screw 1
33 Cover Spring 1
34 Blade Cover 1
35 Guide Base 1
36 Lock Pad 1
37 Upper Bearing Post 1
38 Ball Bearing 2
39 Pin 2
40 Flat Washer 3
41 Hex Socket Cap Screw 4
42 Power Switch 1
43 Switch Plate 1
part Description Qty
44 Phillips Screw Assy 6
45 End Cap 1
46 Flat Washer 2
47 Frame 1
48 Tracking Lock Lever 1
49 Cord Clip 2
50 Power Cord 1
51 Phillips Screw 9
52 Lock Spring 2
53 Hex Socket Set Screw 1
54 Guide Adjusting Gear 1
55 Wave Washer 1
56 Adjustment Knob Base 1
57 Tilt Indicator Screw 1
58 Lower Guide Block 1
59 Guide Height Knob 1
60 Housing Knob 2
61 Flat Washer 2
62 Hex Socket Cap Screw 2
63 Hex Bolt 1
64 Nut With Flange 1
65 Nut,Type I 5
66 Blade Guard 1
67 Round Head Screw 2
68 Knob Axle 1
69 Dust Port 1
70 Star Washer 2
71 Lower Bearing Post 1
72 Miter Gauge Knob 1
73 Flat Washer 4
74 Miter Gauge 1
75 Phillips Screw Assy 1
76 Miter Pointer 1
77 Slide Bar 1
78 Hex Bolt 1
79 Wing Nut 1
80 Tilt Rack 1
81 Flanged Hex Bolt 4
82 Tilt Indicator 1
83 Hex Bolt 4
84 Belt 1
85 Motor Pulley 1
86 Large Washer 1
part Description Qty
87 Hex Socket Cap Screw 1
88 Blade Tracking Knob 1
89 Tilt Knob 1
90 Phillips Screw Assy 2
91 Large Flat Washer 2
92 Spring Washer 1
93 Hex Socket Screw 2
94 Hex Wrench 1
95 Combination Wrench 1
96 Guide Lock Knob 1
97 Table Lock Knob 2
98 Fence Fixed Plate 1
99 Fence Lock Spring 1
100 Fence Pad 2
101 Fence 1
102 Fence Lock Pad 2
103 Fence Bracket 1
104 Fence Clamp 1
105 Clamp Rod 1
106 Flat Washer 2
107 Hex Bolt 2
108 Hex Socket Screw 1
109 Lower Blade Guide 1
110 Upper Blade Guide 1
111 Eccentric Shaft 4
112 Split Washer 4
113 Ball Bearing 4
114 Set Screw 4
115 Tension Rod 1
116 Tension Spring 1
117 Wrench 1
118 Motor 1
119 Cotter Pin 1
120 Blade Tension Lever 1
121 Phillips Screw 1
122 Work Table 1
123 Table Insert 1
124 Phillips Screw 1
125 Hex Lock Nut Insert 2
126 Tension Pad 1
127 Phillips Sunk Screw 1
128 Nut,Type I 1
parts List and Diagram
parts List
Page 15For technical questions, please call 1-888-866-5797.70630
SaFetyOperatiOnMaintenance Setup
assembly Diagram
2
3
3
4
2
4
5
6
7
9
10
10
11
11
12
12
11
13
14
15
16
12
13
12
11
14
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
38
39
40
41
42
43
5
44
45
47
46
48
88
49
50
51
96
52
46
4
53
54
55
56
59
60
61
62
4
60
61
62
63
64
65
66
67
89
52
68
51
69
44
70
44
58
41
71
40
39
73
74
75
76
77
122
78
73
3
79
123
80
81
81
82
57
83
65
84
85
86
87
90
91 92 93
9495
1
8
73
97
117
101
100
99
98
4
100
107
106
102
103
105
104
51
118
115
120
125
121
91
119
116
126
127
125
124
108
128
109
111
113
112
110
111
113
112
114
114
72
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries
to persons or property, or for incidental, contingent, special or consequential damages arising from the use of
our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
26677 agoura road • calabasas, ca 91302 • 1-888-866-5797
