
F3501QQ110V

F3501QQ110V
Installation & Operating Instructions for the
Parrotuncle Owner's Installation ,Manual
WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER

Installation & Operating Instructions for the
Parrotuncle Owner's Installation ,Manual
WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
the floor and the fan blade tips. The fan should be mounted at leaet thirty (30) inches ftom walls or other upright structures.
screws provided with the outlet box most outlet boxes commonly used for the support of lighting fixtures are not acceptable for f
an
support and may need to be replaced. Consult a qualified electrician if in doubt.
model fan you are installing. Switches must be UL. general use switches. Refer to the instructions packaged with the light kits and
switches for proper assembly.
1.
To avoid possible electric shock, turn off the electricity at the main fuse box or circuit panel before you begin the fan installation or
before servicing the fan or installing accessories.
2.
Read all instructions and safety information carefully before installing your fan and save these instructions.
3.
Make sure all electrical connections comply with local codes or ordinances and the National Electrical Code. If you are un
familiar with
5.
WARNING: The outlet box and ceiling support joist used must be securely mounted, and capable of supporting at least 100 pounds. To
reduce the risk of fire, electric shock or personal injury, mount to the outlet box marked acceptable for fan supported and use mounting
screws provided with the outlet box. The box must be supported directly by the building structure.
6.
WARNING: To reduce the risk of fire, electric shock or personal injury, mount to outlet box marked “acceptable for fan support” and use mounting
7.
Electrical diagrams are for reference only. Light kits that are not packed with the fan must UL listed and marked suitable for use with the
8.
After installation is complete, check that all connections are absolutely secure.
9.
After making electrical connections, spliced conductors should be turned upward and pushed carefully up int
o out
let box. The wires
should be spread apart with the grounded conductor and the equipment-grounding conductor on one side of the outlet box.
10.
WARNING: To reduce the risk of electrical shock and fire, do not use this fan with any solid-state fan speed control device, or rheostat.
11.
Do not separate the reverse switch until the fan has come to a complete stop.
12.
Do not insert anything into the fan blades while they are rotating.
13.
WARNING: To reduce the risk of personal injury, do not bend the blade brackets (also referred to as “flanges”) during assembly or after
installation. Do not insert objects in the p
ath o
f the blades.
14.
To avoid personal injury or damsge to the fan and other items,be cautious when working around or cleaning the fan.
15.
Do not use water or detergent when cleaning the fan or fan blades. A dry dust cloth or lightly dampened cloth will be suitable for most cleaning.
NOTE: The important safety precautions and instructions appearing in the manual are not meant to cover all possible conditions and situations that may
may occur. It must be understood that common sense and caution are necessary factors in the nstallation and operation and operation of this fan.
NOTE: This product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities are
different or are impaired, or lack of experience or knowledge, unless such persons are supervised or trained to operate the appliance
by a person responsible for their safety.
NOTE: Children should be supervised to ensure that the
y do not us
e appliances as a toy.
THANK YOU FOR YOUR PURCHASE
Thank you for purchasing this quality product. To ensure correct function and safety, please read and save all
instructions before using the product
SAFETY TIP
electric wiring, please use a qualified and licensed electrician.
4.
Make sure you have a location selected for your fan that allow clear space for the blades to rotate,and at least seven (7) feet of clearance betweem
TECHNICAL INFORMATION
SKU
F3501QQ110V
Rated Voltage
110-120V AC
Scope ofapplication
25±5W
F3501QQ110V
Liht
4*E26MAX.25W(EXCLUDE)

Mounting screws (2PCS)
washer (2PCS)
Pls check whether above accessories are completed or not?Yes,and install.
REMOTE CONTROL(1PCS)
F3501QQ110V
Installation & Operating Instructions for the
Parrotuncle Owner's Installation ,Manual
WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
Balance tapes
(2PCS)
4
spring washer
(2PCS)
Wood screws (4PCS)
Plastic wire nut (7PCS)
Screws for light
(1PCS)
1
2
3
2h
4h
8h

1
2
3
F3501QQ110V
Installation & Operating Instructions for the
Parrotuncle Owner's Installation ,Manual
WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
Outlet box
washers
spring washer


F3501QQ110V
For Mounting Controller. Models GA043
Models
RECEIVER


F3501QQ110V
Installation & Operating Instructions for the
Parrotuncle Owner's Installation ,Manual
WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
MODEL
OUTPUT

Installation & Operating Instructions for the
Parrotuncle Owner's Installation ,Manual
F3501QQ110V
WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER

Installation & Operating Instructions for the
Parrotuncle Owner's Installation ,Manual
F3501QQ110V
WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
size of product
Ø150 [5 29/32"]
Ø26.5 [1 1/16"]X4"or10"
263 [10 11/32"]
306 [12 1/16"]
458.9 [18 3/32"]
Ø410 [16 5/32"]
Ø410 [16 5/32"]
Ø910 [35 27/32"]
152.9 [6"]
Ø910 [35 27/32"]


Installation & Operating Instructions for the
Parrotuncle Owner's Installation ,Manual
WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
Verify all blades and blade bracket screws are secure (most fan wobble problems are caused by loose parts). Once fan is properly
3. THE FAN WOBBLES
installed, run the ceiling fan for 10 minutes to let the fan self-adjust.
If wobble occurs a
er running the fan for 10 minutes, verify blade level using the following process:
a) select a point on the ceiling above the
p of one of the blades. Then select the fan blade and measure from the center
of the selected blade to point on the ceiling. Rotate the fan un
e next blade is
oned and repeat the
measurement using the same point from the ceiling for every blade. Measurements
should be within 1/8 inch.
Customer Service Supprt@parr
otuncle.com to order a complimentary Blade Balancing Kit
Customer Service Support@parrotuncle
-com to order a complimentary Blade Balancing Kit
4.LIGHT ISNOTWORKING
Check Bulb to make sure it is installed correctly
Remove non-working bulb and replace with a bulb that is known to be a good working bulb
To reset the remote control: 1) Turn off power to fan using the wall switch or circuit breaker. 2) Remove ba
eries from
remote. 3) Wait 10 seconds. 4) Replace ba
and turn power on
F3501QQ110V

AFTER INSTALLATION
WOBBLE”
The fan blades have been adjusted in the factory to minimize any wobble
NOTE:CEILING FANS TEND TO MOVE DURING OPERATION DUE TO THE FACT THAT THEY
ARE MOUNTED ON A RUBBER CROMMET. IF THE FAN WAS MOUNTED RIGIDLY TO THE
CEILING, IT WOULD CAUSE EXCESS VIBRATION. MOVEMENT OF A FEW CENTIMENTERS
IS QUITE ACCEPTABLE AND DOES NOT SUGGEST ANY PROBLEM
TO REDUCE THE FAN WOBBLE: PLEASE CHECK THAT ALL SCREWS WHICH SECURED THE MOUNTING
BRACKET AND DOWNROD ARE SECURE.
BALANCING A WOBBLING CEILING FAN:
For your convenience, a Balancing Kit is included; please follow this procedure when balancing the fan:
1.Check that all blade and blade arm screws are secure.
2.Most fan wobbling problems are caused when blade levels are unequal. Check this level by
selecting a point on the ceiling above the tip of one of the
blades. Measure this distance.Rotate the fan until the next blade is positioned for
measurement. Repeat for each blade. The distance deviation should be equal within
1/8"(0.32cm).
3.Use the enclosed Blade Balancing Kit if the blade
wobble is still noticeable.
4.If the blade wobble is still noticeable, interchangin
g two
adjacent (side by side) blades can redistribute the weight and possibly result in smoother
operation. WARNING: TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE
BLADE ARM WHILE INSTALLING, BALANCING THE BLADES, OR CLEANING THE FAN. DO
NOT INSERT FOREIGN OBJECTS BETWEEN ROTATING FAN BLADES.
NOISE
When it is quiet(especially at night) you may hear occasional small noises. This is normal. Please allow
a 24-hour “breaking-in” period, most noises associated with a new fan disappear during the time.
CARE AND CLEANING
1.Periodic cleaning of your ceiling fan is the only maintenance required. Use a soft brush or lint free cloth to
avoid scratching the paint finish. Please make sure to turn off electricity power before you clean your fan
2.Do not use water when cleaning your ceiling fan. It could damage the motor or the blades
and create the possibility of an electrical shock.
3.Motor has permanently lubricated ball bearing. No need to oil
NOTE: MAKE SURE THE POWER IS OFF AT THE ELECTRICAL PANEL BOX BEFORE YOU
ATTEMPT ANY CLEANING OR REPAIRS.
Installation & Operating Instructions for the
Parrotuncle Owner's Installation ,Manual
WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
F3501QQ110V

