F a u c e t
SAFETY INSTRUCTIONS 1
Prior to Installation
Safety Tips
Care and Maintenance
SPRING KITCHEN FAUCETS 2
Parts
Tools
Assembly
PULL DOWN KITCHEN FAUCETS 6
Parts
Tools
Assembly
SINGLE HANDLE KITCHEN FAUCETS WITH SPRAYER 10
Parts
Tools
Assembly
DOUBLE HANDLE KITCHEN FAUCETS WITH SPRAYER 14
Parts
Tools
Assembly
TROUBLESHOOTING 18
TABLE OF CONTENTS
1
Prior to Installation
Make sure that the cold and hot water lines are turned off.
Wrap all threaded connections with Teflon tape. Always wrap in a clockwise
direction.
Cover your drain to avoid losing parts.
Do not disassemble the main faucet body, as it has been installed and commissioned
correctly and precisely before delivery to the factory.
To keep the faucet from jamming, flush the water pipe before installation.
Using condition: Working pressure at 0.05-1.0 MPa (including cold and hot water
pressure) with applicable water temperature: 39.2°F - 1 94°F.
Care and Maintenance
To keep the product clean and shining, follow the steps below:
1. Rinse clean with water and dry with a soft cloth.
2. Do not clean with soaps, acid, polish, abrasives, or harsh cleaners.
3. Do not use cloth with a coarse surface.
4. Unscrew the aerator and clean when necessary.
Safety Instructions
If soldering the water connections when installing the faucet, remove the O-rings,
cartridges, and washers before applying any heat.
Protect your eyes when cutting or soldering.
Do not over tighten screws/nuts. Finger tighten, then use a wrench/screwdriver to
tighten the fixing screw/nut until snug.
2
Spring Kitchen Faucet
3
Tools:
Time required:
+/- 45 minutes
Wrench
Legend:
Hot Water
Warning
Cold Water
Plumber’s Tape
Grease
Screwdriver
Bucket
Spring Kitchen Faucet
4
Spring Kitchen Faucet
5
Spring Kitchen Faucet
6
Pull Down Kitchen Faucets
7
Tools:
Time required:
+/- 45 minutes
Wrench
Legend:
Hot Water
Warning
Cold Water
Plumber’s Tape
Grease
Screwdriver
Bucket
Pull Down Kitchen Faucets
8
Pull Down Kitchen Faucets
9
Pull Down Kitchen Faucets
10
SINGLE HANDLE FAUCETS
11
Tools:
Time required:
+/- 45 minutes
Wrench
Legend:
Hot Water
Warning
Cold Water
Plumber’s Tape
Grease
Screwdriver
Bucket
SINGLE HANDLE FAUCETS
12
SINGLE HANDLE FAUCETS
13
SINGLE HANDLE FAUCETS
14
DOUBLE HANDLE FAUCETS
15
Tools:
Time required:
+/- 45 minutes
Wrench
Legend:
Hot Water
Warning
Cold Water
Plumber’s Tape
Grease
Screwdriver
Bucket
DOUBLE HANDLE FAUCETS
16
DOUBLE HANDLE FAUCETS
17
DOUBLE HANDLE FAUCETS
18
Problem
There is leakage under the
handle.
Water will not shut off
completely.
There is a leak between the
spray head and the hose.
The locking nut has
come loose.
Cartridge may be
defective.
The spray head may be
loose or the washer is
not seated correctly in
the hose connection.
Unscrew the lever on the
handle by hand. Loosen set
screw with a hex wrench.
Remove the handle and
unscrew trim cap by hand.
Tighten locking nut with an
adjustable wrench.
Unscrew the level on the
handle by hand. Loosen set
screw with a hex wrench.
Remove the handle and
unscrew trim cap by hand.
Unscrew the locking nut with
an adjustable wrench. Remove
ceramic disc cartridge. Check
for cracks.
Tighten the spray head by
hand until snug. Make sure the
washer is seated correctly.
Possible Cause
Solution
Troubleshooting
19
NOTES
Kitchen and Bath
Three Locations:
350 Parr Circle
Reno, NV 89512
916 Delaware Avenue
Marysville, OH 43040
319 Rowland Mill Rd.
Bruceton, TN 38317
www.zlinekitchen.com
1-614-777-5004
