Tablet PC
Settings - About Tablet - Certificationy information.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harm full interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by manufacturer
could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1)This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Specific Absorption Rate (SAR) information:
This Device meets the government's requirements for exposure to radio waves. The guidelines are
based on standards that were developed by independent scientific organizations through periodic
and thorough evaluation of scientific studies. The standards include a substantial safety margin
designed to assure the safety of all persons regardless of age or health. FCC RF Exposure
Information and Statement the SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of
tissue. Device types: Device has also been tested against this SAR limit. This device was tested for
typical body-worn operations with the back of the device kept 0mm from the body. To maintain
compliance with FCC RF exposure requirements, use accessories that maintain an 0mm separation
distance between the user's body and the back of the device. The use of belt clips, holsters and
similar accessories should not contain metallic components in its assembly. The use of accessories
that do not satisfy these requirements may not comply with FCC RF exposure requirements, and
should be avoided.
‐ English: This device contains licence-exempt transmitter(s)/receiver(s) that
comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired
operation of the device.
‐ French:Cet appareil contient des émetteurs/récepteurs exempts de licence qui sont
conformes aux CNR exempts de licence d’Innovation, Sciences et Développement économique
Canada. Le fonctionnement est soumis aux deux conditions suivantes :
(1) Cet appareil ne doit pas causer d’interférences.
(2) Cet appareil doit accepter toute interférence, y compris les interférences susceptibles de
provoquer un fonctionnement indésirable de l’appareil.
The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the
potential for harmful interference to co-channel mobile satellite systems.
L'appareil destiné à fonctionner dans la bande 5150-5250 MHz est uniquement destiné à une
utilisation en intérieur afin de réduire le potentiel d'interférences nuisibles aux systèmes
mobiles par satellite cocanaux.
SpecificAbsorption Rate (SAR) information:
This device meets the government's requirements for exposure to radio
waves. The guidelines are based on standards that were developed by independent
scientific organizations through periodic and thorough evaluation of scientific studies.
The standards include a substantial safety margin designed to assure the safety of all
persons regardless of age or health.ISED RF Exposure Information and Statement
the SAR limit of and Canada(ISED) is 1.6 W/kg averaged over
one gram of tissue. Devicetypes: device has also been tested against this SAR limit.
This device was tested for typical body-worn operations with the back of the device
kept 0mm from the body. To maintain compliance with ISED RF exposure
requirements, use accessories that maintain an 0mm separation distance between
the user's body and the back of the device. The use of belt clips, holsters and similar
accessories should not contain metallic components in its assembly. The use of
accessories that do not satisfy these requirements may not comply with ISED RF
exposure requirements, and should be avoided.
Informations sur le débit d’absorption spécifique (DAS) :
Cet appareil répond aux exigences gouvernementales en matière d’exposition aux
ondes radio. Les lignes directrices sont fondées sur des normes qui ont été
élaborées par des organismes scientifiques indépendants dans le cadre d’une
évaluation périodique et approfondie d’études scientifiques. Les normes
comprennent une marge de sécurité substantielle conçue pour assurer la sécurité de
toutes les personnes, quel que soit leur âge ou leur état de santé. La limite DAS du
Canada (ISDE) est de 1,6 W/kg en moyenne sur un gramme de tissu. Types
d’appareils : l’appareil a également été testé par rapport à cette limite DAS. Cet
appareil a été testé pour des opérations typiques portées sur le corps, l’arrière de
l’appareil étant à 0 mm du corps. Pour maintenir la conformité aux exigences
d’exposition RF d’ISDE, utilisez des accessoires qui maintiennent une distance de
séparation de 0 mm entre le corps de l’utilisateur et l’arrière de l’appareil.
L’utilisation de clips de ceinture, d’étuis et d’accessoires similaires ne doit pas
contenir de composants métalliques dans son assemblage. L’utilisation d’accessoires
qui ne satisfont pas à ces exigences peut ne pas être conforme aux exigences
d’exposition aux RF d’ISDE et doit être évitée.
