MYST
HUMIDIFIER
User Manual
MA-04
READ AND SAVE THESE INSTRUCTIONS
AND WARNINGS
FAILURE TO COMPLY WITH THE WARNINGS LISTED BELOW MAY
RESULT IN ELECTRIC SHOCK OR SERIOUS INJURY.
This product should be used only in accordance with the specications
outlined in this manual. Usage other than what has been specied here may
result in serious injury. When using electrical appliances, basic precautions
should always be followed to reduce the risk of re, electric shock and injury to
persons, including the following:
ATTENTION!
• IMPORTANT - This appliance has a polarized plug (one blade is wider than
the other). To reduce the risk of electric shock, this plug is intended to t in
a polarized outlet only one way. If the plug does not t fully in the outlet,
reverse the plug. If it still does not t, contact a qualied electrician. Do not
attempt to defeat this safety feature.
• To avoid re or shock hazard, plug the appliance directly into the right AC
electrical outlet.
• Keep the cord out of heavy traic areas. To avoid re hazard, NEVER put the
cord under rugs, near heat registers, radiator, stoves or heaters.
• The power plug must be connected in such a way as to avoid risks if the
humidier is tipped over or liquid is spilled.
• Ensure that the mist outlet, air inlet and outlet is not covered.
• If the power outlet used to operate the humidier is not properly connected,
the power plug of the device will get hot. Ensure that you are using a
properly connected power outlet for the humidier.
• DO NOT add hot water into the water tank. Use only cold water (tap water,
distilled water, or other drinking water)
• DO NOT drink the water used in the water tank or device base and do not
use it for animals or plants. Empty the water tank and base into a drain.
• DO NOT touch the PTC heater to avoid burning.
!
• DO NOT operate the device if the power plug or power cord is defective.
• DO NOT spray ammable materials, e.g. pesticides or fragrances, near the
humidier.
• DO NOT place any objects on top of the humidier, and do not sit or stand
on it.
• DO NOT use the humidier aer using incense for insect protection or in
places with oil residue or chemical vapors or where incense sticks are burnt.
• DO NOT use the humidier near heaters, replaces, or gas powered devices.
• DO NOT attempt to repair or adjust any electrical or mechanical functions
on this device. Doing so will void your warranty. The inside of the device
contains no user serviceable parts. All servicing should be performed by
qualied personnel only.
• DO NOT use outdoors.
• NEVER tilt, move, or attempt to empty the base while it is in operation.
Power o and unplug before moving the device.
• NEVER use detergents, gasoline, glass cleaner, furniture polish, and paint
thinner, or other household solvents to clean any part of the humidier.
• NEVER place the base under water ow or immerse in liquids.
• Clean the base and water tank every week to get the clean and hygienic mist.
PRODUCT TROUBLESHOOTING
PLEASE NOTE: IF YOU EXPERIENCE A PROBLEM, DO NOT ATTEMPT TO OPEN
THE HOUSING BY YOURSELF. DOING SO MAY VOID YOUR WARRANTY AND
CAUSE DAMAGE TO THE HUMIDIFIER OR RESULT IN PERSONAL INJURY.
ISSUE CHECKLIST POSSIBLE SOLUTION
No mist
Whether power is on Press the power button.
Whether power plug is
plugged tightly
Unplug and then plug again. When the
power is returned, try again.
Whether water tank is not
empty or attached to the
base correctly
Add water and make sure the tank is
correctly attached to the base.
Whether the ultrasonic trans-
ducer is not covered by white
dust, scale or other objects.
Clean the ultrasonic transducer or
remove the objects on it.
Air blows but
no mist
Whether the ultrasonic
transducer is not covered by
white dust, scale or
other objects.
Clean the ultrasonic transducer or
remove the objects on it. Suggest to use
so or distilled water if your area has
hard water.
The humidity has
a bad smell
Whether water is clean
and no foreign objects
in the water
Clean the device thoroughly, and ll it
with fresh water.
White dust is
forming on
Whether your area uses
hard water
Use distilled water if this becomes a
nuisance. Remember to clean the lter
aer use for a short time.
Device has
stopped working
Whether water tank is not
empty or attached to the
base correctly
Add water and make sure the tank is
correctly attached to the base.
Water is accumu-
lating outside of
the device or the
surrounding area.
Whether device is level Unplug and place on level surface.
Lower mist level setting and point mist
nozzle away from objects. Raise device
on a water-resistant level surface 2-3 feet
o of oor.
Water drips
when relling
Whether water remains on
the bottom of the tank
Wipe tank or tilt to drain before
transporting.
Increased
noise level
Whether device is placed on a
at, level, hard surface
Unplug and place on level surface.
Make sure it is NOT placed on a so or
absorbent surface.
GET TO KNOW THE MYST
Water tank cover
Handle
Base
PTC heater
Ultrasonic
transducer
Mist Nozzle
Water tank
Water tank Base
Aroma drawer
Air inlet
Filter
Air outlet
*DO NOT touch the
PTC heater to avoid burn.
PRIOR TO FIRST USE
1. Place the device upright on a solid, level, and water resistant surface.
Keep the device away at least 4 inches/10 cm from walls for best results.
2. To ensure optimum performance of the device, please ensure that the mist
outlet, air inlet and outlet are not covered.
3. Inspect the power cord to ensure that it is not damaged.
4. Add water to the water tank and ensure water level not exceeding
the “MAX” mark.
5. Connect the power cord to a power outlet. When connected, the buzzer
sounds and all lights ash in a ash. Then the device enters into standby
mode, you can simply press the Power button to start using the Myst.
No Water in Water Tank or No Water Tank
If there is no water in the water tank or no water tank, the buzzer sounds, the red
indicator light on Power Button and “E1” on display will ash at the same time,
the device will stop producing mist automatically while the fan keeps working.
Rell water or place the water tank back to resume normal operation.
Aromatherapy
Push and then pull out the aroma box. Add 2-3 drops of essential oil to the
cotton pad. Do not let the essential oil get in touch with other parts of this device
which will result in damage to the plastics.
POWER
MIST LEVELS
Low / Med / High
TIMER
2hrs / 4hrs / 8hrs / 12hrs / Turn o.
AUTO
Myst monitorsenvironment humidity
and maintains it to a perfect 60%.
SLEEP
Long press (2s) to enter sleep mode.
Press any button to wake up.
WARM MIST
LIGHTING MODES
L1- Mood Light
L2- Pick a color, Any color
L3- Deep Breathing Meditation
HOW TO OPERATE THE MYST
+
HOW TO OPERATE THE MYST BY
REMOTE CONTROLLER
AUTO Mode: ON / OFF
Same as the Mist Level
button on unit
Same as the WARM
button on unit
Sleep Mode: ON / OFF
Switch between Light Mode
of RGB Random / Set Color / OFF
Same as the Power
button on unit
*Notice: Before use, remove the insulation sheet from the bottom of the remote control.
Same as the Timer
button on unit
Switch between Light Mode
of Breathing Light / OFF
HOW TO CLEAN THE MYST
ATTENTION!
ALWAYS POWER OFF AND UNPLUG THE DEVICE BEFORE CLEANING THE DEVICE.
WIPE THE SURFACE OF THE DEVICE WITH A SOFT AND DAMP CLOTH IF NEEDED.
WARNING!
• Do not clean the device with cleaning chemicals of any kind as they may
contain bleach. Use water, dish soap or vinegar solution ONLY.
• No touching or cleaning the PTC heater before it cools down in case of any
accidental injury.
Water tank
Remove the water tank cover, empty the water tank. Use water, vinegar
solution or dish soap to wash the inside of the water tank. Use a cloth or a
cleaning brush if needed, then rinse it until clean.
Water tank cover
Remove and wash the cover with water or vinegar solution. Use a cloth or a
cleaning brush if needed, then rinse it until clean.
Filter inside the water tank
Take out the lter set from the water tank. Wash the lter which may
accumulate large particles. Aer cleaning, assemble it back to the water tank.
Base
Follow the draining direction mark to pour excess water out of the base.
Clean the base with a cleaning brush or a so damp cloth. DO NOT submerge
the base into water and AVOID water entering the base inside through the air
inlet or air outlet.
Ultrasonic transducer and PTC heater
ONLY use the enclosed cleaning brush to gently clean the ultrasonic
transducer and PTC heater to remove the build-ups and deposits thoroughly.
Do not scrub or scrape the ultrasonic disk and PTC heater.
HOW TO DESCALE
TRANSPORT AND STORAGE
Depending on usage and water quality, cleaning to remove scale may be
required weekly or every other week to optimize performance. If you live in a
hard water area, distilled water is recommended to be used on this device.
This will help reduce the precipitation of minerals or ‘white dust’.
If scale becomes diicult to be removed with cleaning brush:
WARNING! Always power o and unplug the device before transporting it.
Always Transport the device only when the water tank is empty.
We recommend carefully cleaning the humidier before storing it. Ensure that
all parts are clean and dry prior to storage. Do not leave any water in the device.
Water that remains in the device may result in mineral deposits and promote the
growth of undesired micro organisms. Store the device in a cool and dry location.
1. Fill the base with vinegar solution: mixture of 1 tsp. white vinegar and
1 tsp. water.
2. Let the solution stand for 5 minutes.
3. Clean all surfaces with a so cloth or cleaning brush to help remove scale.
4. Rinse the base thoroughly with water to remove scale and vinegar solution.
5. Also check the mist nozzle, tank cover, sealing ring, lter and mist channel in
the water tank. Clean them with vinegar solution if needed.
Model number: MAH-01W
Humidication mode: Miko MYST Top Filling Ultrasonic Warm/Cool Mist
Power supply: 120V~, 60Hz
Power consumption: 30W(cool mist), 90W(warm mist)
Tank capacity: 4.5L
Mist output: 300ml/h(cool mist), 400ml/h(warm mist)
Dimensions: 195*195*319mm/ 7.7*7.7*12.6 in
Please dispose of this product aer its service life pursuant to the
Waste Electrical and Electronic Equipment Directive 2012/19/EU- WEEE.
The symbol on the product or its packaging indicates that this product
cannot be treated as normal household waste but must be returned to a
collection point for recycling electrical and electronic products.
TECHNICAL DATA
CORRECT DISPOSAL OF THIS PRODUCT
