Document
Technical Specification
version: v1.00
status:
date: 2025-11-24
project title: PUR-SCANIT-350U HILTI – User Manual
org
20251124_EN_UM - PUR-SCANIT-
350U Hilti_v1.00.docx
created by: Jochen Kuhn
page: 1 von 3
RF-Embedded GmbH • Kufsteiner Straße 11 • D-83080 Oberaudorf • [email protected]
www.rf-embedded.eu
PUR-SCANIT-350U HILTI
USER MANUAL
Document
Technical Specification
version: v1.00
status:
date: 2025-11-24
project title: PUR-SCANIT-350U HILTI – User Manual
org
20251124_EN_UM - PUR-SCANIT-
350U Hilti_v1.00.docx
created by: Jochen Kuhn
page: 2 von 3
RF-Embedded GmbH • Kufsteiner Straße 11 • D-83080 Oberaudorf • [email protected]
www.rf-embedded.eu
1 Plug-In
To start working with the PUR-SCANiT350U, plug the USB connector into a free USB port of your
computer. The PC will then ask you for a valid driver.
2 Driver
The driver will be installed automatically by your Operating System, Windows 10 or Windows 11.
3 Software
1) Connect the Reader to the PC.
2) Use the COM port assigned to the reader in the next steps, for example COM1.
3) Start the Skript on the CMD line:
python toolbox.py COM1 bridge
→Adjust the COM port number to match that of the device.
4) Use the reader as usual with the Silion Demo Tool.
Document
Technical Specification
version: v1.00
status:
date: 2025-11-24
project title: PUR-SCANIT-350U HILTI – User Manual org
20251124_EN_UM - PUR-SCANIT-
350U Hilti_v1.00.docx
created by: Jochen Kuhn
page: 3 von 3
RF-Embedded GmbH • Kufsteiner Straße 11 • D-83080 Oberaudorf • [email protected]
www.rf-embedded.eu
Declaration of Conformity for USA
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable
protection againstharmful interference in a residential installation. This equipment generates,
uses and can radiateradio
frequency energy
and,
if
not installed and used
in
accordance
with
the
instructions,
maycause
harmful interference to radio communications.
However,
there
is no
guarantee
thatinterference
will
not occur
in
a
particular
installation.
If
this
equipment
does cause
harmfulinterference to radio or television reception, which can be
determined by turning the equipmentoff
and
on,
the user is
encouraged
to
try
to correct the
interference
by
one or more of
thefollowing measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution:
Any changes
or modifications to this device not
explicitly approved by
manufacturer
could void your authority to operate this equipment.
This device
complies
with
part
15 of the
FCC
Rules.
Operation
is
subject
to the
following
two
conditions:
(1)This
device
may
not cause harmful
interference,
and
(2)
this device must
accept any
interference received, including interference that may cause undesired operation.
This
equipment complies
with FCC
radiation
exposure
limits set forth for an uncontrolled
environment. This
equipment
should be installed and
operated
with
minimum distance 20cm
between the radiator and your body.
