
�D ����LE

1
2
8
11
15
15
Things To Know And Do Before Use
The Controller Instructions
Operation Guide
Important Safety Instructions
Product Parts
10
29
30
31
32
34
FAQ
Cleaning And Maintenance
After Massage
35
FCC Radiation Exposure Statement
36
Industry Canada Notice
Side Panel Control Instructions

2
IMPORTANT SAFETY INSTRUCTIONS
When using this product, basic precautions should always be followed, including the following:
Read all instructions before using (this product).
DANGER-To reduce the risk of electric shock:
• Always unplug this product from the electrical outlet after using and before cleaning.
• Never use unauthorized parts or hardware for this chair. No modifications are allowed.
• Carefully examine the covering before each use. Carefully examine the upholstery from top to
bottom. If there are any signs of cracking, blistering, rethreading or tearing, stop using the
product and contact the manufacturer for a replacement or further instructions. Please unplug
the chair from the power outlet.
• This product must be kept a climate-controlled area. 60-85 degrees Fahrenheit with very low
moisture at ALL times.
WARNING-To reduce the risks of burns, fire, electric shock or injury to persons:
• An appliance should never be left unattended when plugged in. Unplug from outlet when not in
use and before any authorized installs or alterations are being made.
• Close supervision is required if you have any pets, children in the area when chair is being used.
• Use this product only for its intended use as described in this manual. Do not use attachments
not recommended by the manufacturer.
• Never operate this product if it has a damaged cord or plug, if it is not working properly, if it has
been dropped, damaged or dropped into water. Contact the manufacturer for examination and
repair.
• Keep the cord away from heat source like a vent or a humid area like a bathroom.
• Never pull on any cables wire on this product.
• If any of the air hoses are plugged stop using the chair and contact the manufacturer and unplug
power from the outlet.
• Never allow for any object to fall into the chair or cracks of the chair.
• This product is for indoor use only in a dry climate controlled area.
• Do not operate where aerosol (spray) products are being used or where oxygen is being
administered.
• To disconnect, turn all controls to the off position then remove plug from outlet.
• Keep children away from this product as working parts can seriously injure a child or pet.
• Connect this appliance to a properly grounded outlet only. See Grounding Instructions.
• Carefully Monitor the heating areas of the chair. If there is any abnormality or discomfort, turn off
the chair, unplug the power from the outlet and contact the manufacturer.
• Do not operate this product using a blanket or pillow. Excessive heating can occur and causing
fire, electric shock or injury to persons.
• Any elderly, handicap person, children (under 18) or with any person with a medical must consult
with a medical doctor if this product can be used.
Any person with an implanted medical device or medical condition or under any
treatment must get approval from your medical doctor before using this device.
SAVE THESE INSTRUCTIONS
Important Safety Instructions

If you feel unwell while using or after using the chair, stop immediately and contact your physician.
Do not use the chair again unless approved by your doctor.
3
Any person with a pacemaker cannot use this
product. The chair may cause an electronic
malfunction to the medical device;
Persons with any injuries should not use
this product.
Persons with higher or lower regular body
temperature, fever, inflammation, cold
symptoms, high blood pressure or any poor
health conditions should consult a
physician before using this product;
Person unable to feel or insensitive to heat
on their skin such as a diabetic patient;
Pregnant women or ones that have just
given birth;
Patients with malignant tumors;
Patients with heart disease;
Persons with poor blood circulation such as
a diabetic patient;
Otherwise discomfort or even physical injuries may occur.
Any one with spinal or nerve conditions;
Avoid falling asleep in this chair;
Persons with protrusion of intervertebral
disc;
Keep long hair away from moving massage
mechanism while in use.
Do not wear loose clothing or jewelry as it
might get caught with massage
mechanism;
Osteoporosis patients, spinal fracture
patients or persons with acute painful
disease or injuries such as joint sprains or
muscle strains;
Before operating or adjusting the chair, be sure that there are no obstructions that can cause
damage to your chair. No pets or persons, near, in front or under the chair to avoid serious injury.
Before using the chair, look behind the backrest pad and inspect the area where the massage
rollers travel up and down for any tearing or abnormal wear. Be sure the middle nylon cover is not
unzipped and has no signs of damage or tear caused by the roller heads. Using the chair while the
roller heads are exposed could cause physical injury, electrical shock or breakage.
When using the chair for the first time, it is recommended that you select the “Demo” mode to get
familiar with various massage features of the chair.
Do not use the chair for more than 30 minutes each time.
Do not massage a single part of your body for more than 5 minutes.
After using the chair, it is recommended that the chair is unplugged from the power outlet to avoid
any surges caused by outages. It is HIGHLY ADVISABLE TO ALWAYS USE A SURGE PROTEC-
TOR. Keep children or minors from using the chair without supervision to avoid misuse that could
result in serious injuries.
Follow the local code and regulations about use of electrical products。
Use a 110V-120V, 60Hz power supply.
(Do not use the chair in a country this product is not designed for or connect it with a transformer.)
It may lead to electrical shock, product failure or internal components overheating causing fire
hazard.
Make sure the power cable is firmly plugged into the outlet to avoid power surges, short and
electrical shocks. Electrical shocks may cause internal component overheating causing fire
hazard.
In the case of any abnormality with functions of the chair, stop using the chair immediately and
pull out the power plug to avoid smoke, fires and electric shocks.
Abnormality and fault examples are:
If the chair is plugged in and the power switch is in the “ON” position and if the chair is not
responding.
When the chair is turned off but still operating.
If you detect any burning smell or abnormal sounds.
If you detect any parts of the upholstery that seemed to have melted due to over heating.
In any of these listed issues have occurred STOP using the product and unplug from the power
outlet. Have the product inspected by an authorized service center.
Wipe and clean the power plug regularly with dry cloth to avoid dirt or moisture built up.
Do not put any cushions or obstructions between the backrest pad and the backrest. This may
damage the mechanism and result in personal injury.
When moving or handling the chair, be sure to hold onto the recommended supported area. Other-
wise parts of the chair may break resulting in serious injury.
Failing to follow these instructions, discomfort or even physical injuries may occur.
→

4
People with the following health issues should NOT use this chair:
Persons for whom massage is not advisable by doctors. Such as persons with thrombosis,
serious aneurysm, acute venous aneurysm, various skin inflammations (such as subcutaneous
tissue inflammation) or various skin infections.
Otherwise it may aggravate or cause serious injury.
Do not put hands, arms or feet into the traveling massage mechanism while the chair is operating.
Keep small children away from the chair. Climbing could result in falls that could lead to serious
injuries.
Do not climb onto the backrest or the armrests.
Do not apply excessive pressure leaning back on the backrest.
Keep your head away from reachable areas of the backrest and the back cover.
Young persons or persons with physical disabilities that can not operate the chair on their own,
should not use this product or without supervision. Anyone with weaken physical conditions
should consult a doctor before using the chair.
When massaging the neck area, pay attention to the intensity of the massage and make sure it
does not hurt the neck muscles or nerves.
Anyone with physical injuries or poor health should NOT use this product.
Persons with acute lumbago, protrusion of intervertebral disc or displacement of a lumbar
vertebra.
Otherwise it may aggravate or cause serious injury.
Do not damage the power cord.
Do not damage, alter, bend, twist or use it with any extension cords. Do not place the power cord
close to a heater.
A damaged power cord may result in electric shocks, short circuit or fires.
Please consult with the retailer/dealer from which you bought the product or a designated autho-
rized service center about maintaining your power cord.
When engaging the heat function of massage wheels, avoid prolong contact with the skin in one
position. Otherwise low-heat burns may occur.
Even if the temperature is relatively lower at 104 F~140 F, low-heat burns may happen in spite of
no obvious hot or painful sensation.
Do not insert or pull out the power plug when your hands are wet. Otherwise electric shocks may
happen.
Do not refit, disassemble or repair the product without the help of an authorized service provider.
Otherwise fires, abnormal movements or personal injuries may happen.

5
The following persons (even if they are physically healthy at present) should consult a physician
before using the product.
(1) Persons with muscular atrophy;
(2) Persons with any spinal or back pain or spinal condition;
(3) Persons suffer from sprains or bruising easily;
(4) Persons with motion sicknesss;
(5) Persons who received a heart operation or another vascular operation.
It may cause serious injury if not addressed properly.
Otherwise, it may cause serious injury.
Before sitting on the product, make sure there is no foreign objects obstructing any part of the
chair.
Before sitting on the seat, make sure the massage wheels are in the retracted positions.
Turn off the massage function before you get off the chair.
When the lower leg/foot massage section is not retracting after the massage, retract the footrest
with the remote button.
When unplugging the chair, hold onto the head of the to plug and not the cord to avoid damaging
to the power cord. Damaged cord could result in shock and serious injuries.
Before moving the chair, be sure the backrest is in the upright position and the footrest is
retracted in default positions.
Otherwise, injuries may happen or damage to the chair.
When moving the product by dolly, lay mats on the floor to avoid markings or damage to the floor.
Do not roll the chair on engineered wood or soft wood floorings. Otherwise marks and damage
may occur.
Keep the safety lock key.
Keep children away the remote control.
Before moving the chair, make sure there are no obstructions around. If lifting is required, make
sure to lift from the steel frame of the chair. Be sure to keep the chair in the upright position when
lifting the chair when moving.
Symptoms such as skin inflammation, itching or swelling when using the chair, stop the using the
product immediately and consult a physician.
Do not use the product with other electrical devices at the same time, such as a heating blanket.
Do not place your hands, arms, feet or any parts of your body to massage area that are not
designed for the body parts to avoid discomfort or injuries.
Do not put the knees between the calf massager. This may cause serious injury.
Do not fall asleep while using the product.
Do not use the product after drinking alcohol.
If the airbag on the seat is not completely deflated, do NOT attempt to deflate the air bag by force
or using any tools. Contact the manufacturer to resolve the matter.
(Make sure there are no foreign objects on the back cover, the backrest, the seat surface, the lower
leg/foot massage section or inside surface of the back cushion.)
Otherwise, accidents or injuries from product failure may cause serious injury.

6
Do not put hands or feet between footrest and seat base.
Do not put hands or feet between footrest and side panel.
Do not put hands or feet between seat base and side panel.
Do not put hands or feet between the upper and the lower part of the footrest.
Do not put hands or feet in the gap of seat base.
Do not put pets on the massage chair.
Do not pull out the power plug or turn off the power switch suddenly during massage operation.
Do not stand or sit on the backrest. This may lead to serious injury and damage to the product.
Do not stand or sit on the armrests.
Do not stand or sit on the lower leg/foot massage section or the footrest.
Do not drag or push the product after it is installed.
Do not move the product while there is a person sitting on it.
Do not use the product with other heating devices such as electric blankets.
Otherwise fires may occur due to overheating.
Do not leave the remote controller on the seat, always return it to its holder.
If there are any foreign objects between the backrest and the backrest pad, stop using the chair and
turn off. Remove the foreign object and make sure the chair is operating properly before using
again.
Do not place this chair in locations with high humidity such as the bathroom. Moisture will destroy
electrical components resulting in product failure or worst, electrical shock and other serious
injuries.
Do not use any liquid aerosol sprays around the chair. Otherwise, electric shocks, fire, short circuit
or product failure may happen.
Before cleaning or maintaining the product, always unplug the power cord.
In the case of a power failure, pull out the power plug at once. It is highly recommended to
plug chair into a surge protector to protect the chair from shorting during outages.
When the product is not in used, pull out the power plug.

7
GROUNDING INSTRUCTIONS
This product must be grounded. If it should malfunction or break down, grounding
provides a path of least resistance for the electric current to reduce the risk of
electric shock. This product is equipped with a cord with an equipment-grounding
conductor and a grounding plug. The plug must be plugged into an appropriate outlet
that is properly installed and grounded in accordance with all local codes and ordinances.
Danger-Improper connection of the equipment-grounding conductor can result in a risk
of electric shock. Check with a qualified electrician or serviceman if you are in doubt as
to whether the product is properly grounded. Do not modify the plug provided with the
product – if it will not fit the outlet, have a proper outlet installed by a qualified electrician.
Grounding Pin
Grounded Outlet
Grounded Outlet Box

Note: The Bluetooth speakers will only function when the massage chair is in use.
To play music through your massage chair's speakers, please connect your smartphone,
tablet, or other compatible electronic device to your chair via Bluetooth. Please note that
the Bluetooth connection code is "3D 4000LE".
And please make sure you disconnect the Bluetooth after using so the next user can
connect it.
Back Pad
Seat Pad
Bluetooth Music
Speaker
Bluetooth Music
Speaker
5” Touchscreen
Controller
Side Panel
Headrest
Armrest
Side Panel
Control
Footrest
Side Panel

9
Airbags Position and Numbers
4 Airbags
(Shoulders)
8 Airbags
(Armrests)
8 Airbags
(Calves)
8 Airbags
(Feet)

Side Panel Control Instructions
Power Button
Pause Button
Backrest Up
Button
Backrest Down
Button
Zero Gravity Button
Auto Massage
Button
Power Buon
• When in off state, press this buon to turn the chair on; press it again to
turn it off and chair will return to the original state.
Pause Buon
• Press this buon to pause the massage while press it again to connue
massage.
Auto Massage Buon
• Press this buon to enter the recommended auto massage program.
Zero Gravity Buon
• Press this buon to enter zero gravity mode.
Backrest Up Buon
•
Press this buon to raise the backrest.
Backrest Down Buon
• Press this buon to recline the backrest.
10

Things To Do And Know Before Use
64.2”
22.0”
3.15”
11
PLACE THE CHAIR
Do not expose the product directly under the sunlight or in a high-temperature place
Check all around the chair to make sure there
are no children, pets or any other objects near
the footrest and the back area of the chair.
Otherwise, the chair may not
function properly.
Footrest in
contact with
the floor
Chair base in contact
with the floor
Installation position
Inspect the Space Around the Chair.
“HARDWOOD”

Leg/Footrest Mech
Seat Surface
12
Ensure the plug is fully inserted into
the chair port, and keep the power
cord untangled to prevent any
potential damage.
Ensure No Foreign Objects
within the Seams of the Chair.
Examine the Power Cord & Electrical Plug
Do not put hands, feet or any other foreign objects between the footrest and the seat base.
Do not put hands, feet or any other forgeign objects between the footrest and the side panel.
Do not put hands, feet or any other foreign objects between the seat base and the side panel.
Do not put hands, feet or any other foreign objects between the upper and the lower part of
the footrest.
Do not put hands, feet or any other foreign objects in the gaps of the chair. Otherwise, injuries
may occur.
Inspect the power cord for dirt and dust, which
can cause electrical fires. Keep it clean and
damage-free; wipe the plug with a dry cloth.
Avoid damaging, bending, or twisting the cord.
Never place it under heavy objects or near heat
sources. Damaged cords can lead to shocks,
short circuits, or fires.
For maintenance, consult the store where you
bought the product or an authorized service
center.

13
Ensure that the massage rollers are correctly positioned
Power on the Chair
Insert the power plug into the power outlet.
Ensure the power cord is securely plugged into the
outlet to prevent overheating, shorts, shocks,
or fires.
Adhere strictly to socket and wiring regulations,
using a 110-120V~, 60Hz power supply.
Do not use the product overseas or with
unauthorized transformers to avoid shocks,
malfunctions, or fires.
Never plug or unplug with wet hands to prevent
electric shock.
Before using, please check and ensure that
the position of the mechanism rollers are at
the top of the backrest as shown in the
picture. If the rollers are incorrect, please
press the power switch to reset them to the
default position.

14
Before use, please raise the back pad and
inspect the fabric highlighted in the diagram to
ensure it’s not damaged. In the event of any
fabric damage, even minor, discontinue use of
the product immediately. Unplug the power cord
and contact the local service department to
request a replacement. Using the product with
damaged fabric may result in injury or electrical
shock.
Focus on inspecting the fabric where the massage
wheels on the backrest move.
Make Sure The Fabric Is In Good Condition,
With No Damage, Tears, Or Cracks

2
15
Touch Screen
Pause
ON/OFF
Operation Guide
The Controller Instructions

16
Operation Guide

17
Foot Roller:
• Press once to activate the roller massage. Press again to stop the roller massage.
Heating:
Touch this icon to turn off the heating applied to the back and legs. Touch again to turn it on.
In auto massage mode, the heating will set to default.
3D Mechanism:
• There are 6 adjustable levels for the 3D mechanism intensity.
In auto massage mode, the mechanism intensity will set to default.
Adjust:
• Intensity/ Strength/ Speed: There are 5 different levels for adjustment.
3D+ Sonic Massage:
• Press once to activate high frequency tapping. Press again to stop tapping.
NOTE:
Auto Massage
Touch this icon, the screen will turn to the (Auto Massage) page.
Choose from the 12 automatic massage programs to initiate your massage.
-Rejuvenate : Targets the entire body, offering various techniques to provide relaxation for the
entire body.
-Shiatsu : Uses a combination of gentle kneading and vigorous tapping to relax the muscles in your
neck and lower back.
-Swedish : Targets the muscles in your lower back, waist, and hips, using kneading, clapping, and
Swedish techniques to loosen and relax them.
-General Wellness : Specifically tailored for seniors, incorporating gentle kneading and soft
-Deep Tissue : Intense kneading and tapping to alleviate stress in both the neck and the entire body.
-Gentle Touch : Slow kneading massage that provides a comforting sensation to your entire body.
-Sports : Particularly effective at relieving muscle pain and fatigue.
-Relax : Combines kneading and tapping techniques to focus on the waist and lower back region.
-Neck & Upper Back : Targets the neck and upper back, with the goal of alleviating neck muscle
-Hip Flexor : Tailored for the waist and hips, intended to alleviate muscle soreness and fatigue.
-Thai : Focused on providing a full-body stretching experience.
-Sleep : Gentle, soft kneading techniques to promote relaxation and aid in falling asleep.
clapping techniques.

18

19
A.I. Care (Artificial Intelligence)
• Press the A.I. Care icon, and the screen will switch to the following page, guiding you through the
process of detecting your health pro.
• To ensure that all testing points are covered, recline fully and place your palm on the sensor.
Then, press the button to initiate the detection process.
• You will receive a prompt to firmly place your palm against the electroplate; please do not lift your
palm until the Health Pro diagnostics screen appears.
• The screen will display your health condition, categorized as light, medium, or heavy. The chair will
then automatically generate massage programs based on your health condition scan results.
NOTE:
• For successful use of A.I. Care to scan your body, it's essential to lean back into the electro plates
of the body pain detector and ensure good contact. Failure to do so may result in the scanning
process stopping, requiring a restart.

20
Customization:
- Users have the option to create a personalized massage program and save it for future use.
- Customization allows you to save multiple user profiles, such as User 1, User 2, User 3, and User 4.
If you wish to save a new program and the customization slots are already full, the controller will
prompt you to overwrite an existing customization to make space for the new one.
Here's how:
1. Start by opening the "Manual Massage" menu.
2. Next, edit the massage program according to your
3. Once you've customized the program, save it by selecting the "Save" option as "User X."
4. You can also make direct edits to the "User X" program as needed.
preferences.

21

22
Manual Massage
Function
Clapping
to be adjusted.
at medium speed.
Press the button again to stop the clapping massage function.

Shoulders
This button allows you to activate the air pressure massage mode for your Feet.
Press once to start, press again to stop.
Feet
Full Body
23
Air Massage
Area Massage
Arms
S/P (Spot/Partial)
Press once to localize the massage to a spot point.
Press again to shift massage to a particular area of body.
This will keep the original massage node working on a range of 8cm.
for
for
for
To resume full back massage, press button again.
Full Body
This button controls the massage for full body.
Press once to activate the full body massage.
Press again to stop the full body massage.
among
in
This setting

24
Note
Foot Roller
Press once to activate the roller massage. Press again to stop the roller massage.
Heating
Touch this icon to turn off the heating applied to the back and legs. Touch again to turn it on.
In auto massage mode, the heating will set to default.
3D Mechanism
There are 6 adjustable levels for the 3D mechanism intensity.
In auto massage mode, the mechanism intensity will set to default.
Adjust
Intensity/ Strength/ Speed: There are 5 different levels for adjustment.
3D+ Sonic Massage
Press once to activate high frequency tapping. Press again to stop tapping.

Note
Foot Roller
Press once to activate the roller massage. Press again to stop the roller massage.
Heating
Touch this icon to turn off the heating applied to the back and legs. Touch again to turn it on.
In auto massage mode, the heating will set to default.
3D Mechanism
There are 6 adjustable levels for the 3D mechanism intensity.
In auto massage mode, the mechanism intensity will set to default.
Adjust
Intensity, Strength, Speed: There are 5 different levels for adjustment.
3D+ Sonic Massage
Press once to activate high frequency tapping. Press again, to stop tapping.
25
Spot/Partial
Touch Spot/Partial: you can choose exclusive massage program for Lumbar, Shoulder
Neck, Arm, Buttock and Leg.

26
ReactionReaction
Bluetooth name: 3D 4000LE
Press once to open Bluetooth. Press again to close
Bluetooth.
The bluetooth speaker can only connect with one bluetooth
device at a time. Please turn off your bluetooth device after
using so that other users can enjoy it as well.
This is the shortcut key. It directs the user to their favorite
massage programs.

27
Users can adjust the recline of the backrest by long press the
When you think that is the position you want, then press the icon again to stop the adjustment.
The icon allow you to lift or lower the footrest.
Touch the icon to adjust the chair’s zero-gravity position.Touch the icon to return to
the original position.

28
Touch the icon , the screen will change to the Setting menu.
Users can select language, LED, Child Lock, Brightnesss, Sreen Saver and One Key Auto Test
on this page.

After Massage
One Key Auto Test
29
One Key Auto Test for Chair’s Functions. Before testing the chair, it is suggested not to sit on the
chair. And tap ‘Start’ to begin the functions’ test. You can see whether all functions of the chair are
normal.

Cleaning And Maintenance
microcloth
30
inappropriate

Frequently Asked Questions (FAQ)
31
They will not fit comfortably
an air pump
If there is any discomfort, stop using and
consult with your doctor. In the first few days of using,
you may experience mild soreness. Be sure to monitor
the pain levels and if the soreness does not diminish
before using again.
after the following days, consult with your doctor
experience

32
or
If above solutions are not applicable, kindly refer to “Product Warranty Card” and contact service
center.

33
The product upholstery is deformed or abnormally
hot.
these specific sounds

34
3D 4000LE
Upright: 57.9“ x 29.5” x 43.7”
Recline: 64.2“ x 29.5” x 40.6”
Package Dimension(L x W x H)
Product Dimension
Rated current 1.5A
This equipment contains a certified radio transmission module:
FCC ID:2AOC9-ZENBDM10A
IC:27631-ZENBDM10A
73.0’’ x 30.5’’ x 34.5’’
213.9 lbs
180.8 lbs
50 F-104 F
68 F-140 F

35

36

