BAUMR-AG TOLCCMBM1C4A Portable Cement Mixer Pedestal Stand User Manual

User Manual

[Revision 1.0]

READ THIS MANUAL CAREFULLY BEFORE USE – FAILURE TO DO SO MAY RESULT IN INJURY, PROPERTY DAMAGE AND MAY

VOID WARRANTY. • KEEP THIS MANUAL FOR FUTURE REFERENCE. • Products covered by this manual may vary in

appearance, assembly, inclusions, specifications, description, and packaging.

CMS-14 Mortar Concrete Mixer

E&OE © Baumr-AG 2

Safety

Safety messages are designed to alert you to possible dangers or hazards that could cause death, injury or

equipment or property damage if not understood or followed. Safety messages have the following symbols:

You WILL be KILLED or

SERIOUSLY INJURED if you do

not follow instructions.

You CAN be KILLED or

SERIOUSLY INJURED if you do

not follow instructions.

You CAN be INJURED if you do

not follow instructions or equipment

damage may occur.

It is vital that you read and understand this

user manual before using the product,

including safety warnings, and any assembly

and operating instructions. Keep the manual

for future reference.

Safety precautions and recommendations

detailed here must be fully understood and

followed to reduce the risk of injury, fire,

explosion, electrical hazard, and/or property

damage.

Safety information presented here is generic

in nature – some advice may not be

applicable to every product. The term

"equipment" refers to the product, be it

electrical mains powered, battery powered or

combustion engine powered.

• Before Use - If you are not familiar with the

safe operation/handling of the equipment or

are in any way unsure of any aspect of

suitability or correct use for your

application, you should complete training

conducted by a person or organization

qualified in safe use and operation of this

equipment, including fuel/electrical handling

and safety.

• Do NOT operate the equipment in

flammable or explosive environments, such

as in the presence of flammable liquids,

gases, or dust. The equipment may create

sparks or heat that may ignite flammable

substances.

• Keep clear of moving parts.

• Equipment may be a potential source of

electric shock or injury if misused.

• Do NOT operate the equipment if it is

damaged, malfunctioning or is in an

excessively worn state.

• Do NOT allow others to use the equipment

unless they have read this manual and are

adequately trained.

• Keep packaging away from children - risk

of suffocation! Operators must use the

equipment correctly. When using the

equipment, consider conditions and pay

due care to persons and property.

General Work Area Safety

• Wor

k areas should be clean and well it.

• Do not operate the equipment if

bystanders, animals etc are within

operating range of the equipment or the

general work area.

• If devices are provided for connecting dust

extraction / collection facilities, ensure

these are connected and used properly.

Dust collection can reduce dust-related

hazards.

General Personal Safety

• Wear

appropriate protective equipment

when operating, servicing, or when in the

operating area of the equipment to help

protect from eye and ear injury, poisoning,

burns, cutting and crush injuries. Protective

equipment such as safety goggles,

respirators, non-slip safety footwear, hard

hat, hearing protection etc should be used

for appropriate equipment / conditions.

Other people nearby should also wear

appropriate personal protective equipment.

Do not wear loose clothing or jewellery,

which can be caught in moving parts. Keep

hair and clothing away from the equipment.

• Stay alert and use common sense when

operating the equipment. Do not over-

reach. Always maintain secure footing and

balance.

• Do not use the equipment if tired or under

the influence of drugs, alcohol, or

medication.

• This equipment is not intended for use by

persons with reduced physical, sensory, or

mental capabilities.

General Fuel Safety

• P

etrol/fuel/gasoline is extremely flammable

– keep clear of naked flames or other

ignition sources.

• Do not spill fuel. If you spill fuel, wipe it off

the equipment immediately – if fuel gets on

your clothing, change clothing.

• Do NOT smoke near fuel or when

refuelling.

• Always shut off the engine before

refuelling.

• Do NOT refuel a hot engine.

• Open the fuel cap carefully to allow any

pressure build-up in the tank to release

slowly.

• Always refuel in well-ventilated areas.

• Always check for fuel leakage. If fuel

leakage is found, do not start, or run the

engine until all leaks are fixed.

General Carbon-Monoxide Safety

• U

sing a combustion engine indoors CAN

KILL IN MINUTES. Engine exhaust

contains carbon-monoxide – a poison you

cannot smell or see.

• Use combustion engines OUTSIDE only,

and far away from windows, doors, and

vents.

General Equipment Use and Care

• K

eep packaging away from children and

pets, potential risk of suffocation or

choking.

• The equipment is designed for domestic

use only.

• Handle the equipment safely and carefully.

• Before use, inspect the equipment for

misalignment or binding of moving parts,

loose components, damage, or any other

condition that may affect its operation. If

damaged, have the equipment repaired by

an authorised service centre or technician

before use.

• Prevent unintentional starting of the

equipment - ensure equipment and power

switches are in the OFF position before

connecting or moving equipment. Do not

carry equipment with hands or fingers

touching any controls. Remove any tools or

other items that are not a part of the

equipment from it before starting or

switching on.

• Do not force the equipment. Use the

correct equipment for your application.

Equipment will perform better and be safer

when used within its design and usage

parameters.

• Use the equipment and accessories etc. in

accordance with these instructions,

considering working conditions and the

work to be performed. Using the equipment

for operations different from those intended

could result in hazardous situations.

• Always keep equipment components

(engines, hoses, handles, controls, frames,

housings, guards etc) and accessories

(cutting tools, nozzles, bits etc) properly

maintained. Keep the equipment clean and,

where applicable, properly lubricated.

• Store the equipment out of reach of

children or untrained persons. To avoid

burns or fire hazards, let the equipment

cool completely before transporting or

storing. Never place or store the equipment

near flammable materials, combustible

gases, or liquids etc.

• The equipment is not weather-proof, and

should not be stored in direct sunlight, at

high ambient temperatures or locations that

are damp or humid.

• Do not clean equipment with solvents,

flammable liquids, or harsh abrasives.

• For specific equipment safety use and care,

see Equipment Safety.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

CMS-14 Mortar Concrete Mixer

E&OE © Baumr-AG 3

General Electrical Safety

• I

nspect electrical equipment, extension

cords, power bars, and electrical fittings for

damage or wear before each use. Repair or

replace damaged equipment immediately.

• Ensure all power sources conform to

equipment voltage requirements and are

disconnected before connecting or

disconnecting equipment.

• When wiring electrically powered

equipment, follow all electrical and safety

codes.

• Always use a Residual Current Device

(RCD) (GFCI) / Earth Leakage Circuit

Breaker / Safety Switch when operating this

item (electrical items only).

• High voltage / high current power lines may

be present. Use extreme caution to avoid

contact or interference with power lines.

Electrical shock can be fatal.

General Electrical Safety

• E

lectrically grounded equipment must have

an approved cord and plug and be

connected to a grounded electrical outlet.

• Do NOT bypass the ON/OFF switch and

operate equipment by connecting and

disconnecting the electrical cord.

• Do NOT use equipment that has exposed

wiring, damaged switches, covers or

guards.

• Do NOT use electrical equipment in wet

conditions or in damp locations.

• Do NOT use electrical cords to lift, move or

carry equipment.

• Do NOT coil or knot electrical cords, and

ensure electrical cords are not trip hazards.

General Service Information

• T

he equipment must be serviced or

repaired at authorised service centres by

qualified personnel only.

• Replacement parts must be original

equipment manufacturer (OEM) to ensure

equipment safety is maintained.

• Do NOT attempt any maintenance or repair

work not described in this manual.

• After use, the equipment and components

may still be hot – allow the equipment to

cool and disconnect spark plugs and/or

electrical power sources and/or batteries

from it before adjusting, changing

accessories, or performing repair or

maintenance.

• Do NOT adjust while the equipment is

running.

• Perform service-related activities in suitable

conditions, such as a workshop.

• Replace worn, damaged or missing

warning/safety labels immediately.

Child Choking Hazard!

• W

ARNING: CHOKING HAZARD - CHILDREN UNDER 8 YRS. CAN CHOKE OR SUFFOCATE ON SMALL PARTS. ADULT

SUPERVISION REQUIRED.

• Carefully inspect anything a baby or child could gain access to, including this product & packaging.

• Dangers include anything of a size that could become stuck or lodged in a baby or child's airway.

• Dangers include things like raw, hard fruit and vegetable pieces, large pieces of meat, bones or sausage skins, popcorn, nuts,

hard lollies and corn chips, small magnets and batteries, coins, beads, marbles and small uninflated balloons, broken toys and smaller toys,

buttons, keys, and coins. But there are also many more.

• Pay particular attention to accessories, nuts, bolts, screws, washers, caps, covers, loose parts, parts that could be removed or break off, pieces

of packaging, staples, tape etc.

• In the case of any doubt, secure the item of concern in an appropriate manner, or completely remove the possibility of access by a baby or child.

HAZARDOUS COMPONENTS!

• BE

AWARE THAT THE EQUIPMENT MAY INCLUDE HAZARDOUS COMPONENTS, SUCH AS BLADES, HOT SURFACES AND MOVING

PARTS.

• MOVING BLADES CAN CAUSE SERIOUS INJURY AND EVEN DEATH IF USED IMPROPERLY OR WITHOUT SUFFICIENT PPE.

• DO NOT USE THIS EQUIPMENT ON UNEVEN SURFACES AND ALWAYS MAINTAIN GOOD BALANCE WHEN USING THIS EQUIPMENT.

FAILURE TO DO SO MAY CAUSE SERIOUS INJURY.

• MAINTAIN A SECURE GRIP OF THE TRIGGER ASSEMBLY AT ALL TIMES.

Understand Your Mixer

• R

ead and understand the owner’s manual and labels affixed to the mixer. Learn its application and limitations as well as the specific potential

hazards associated with it.

• Become familiar with the controls before operating this mixer.

Stay Alert

• D

o not operate the mixer while under the influence of drugs, alcohol, or any medication that could affect your ability to use it properly.

• Do not use this mixer when you are tired or distracted from the task at hand. Be mindful of what you are doing at all times. Use common sense.

Avoid Dangerous Conditions

• E

nsure there is adequate surrounding workspace.

• Keep your work area clean and well-lit. Cluttered areas invite injuries. Keep the area around the mixer free from obstructions, grease, oil, trash,

and other debris that could cause someone to fall onto moving parts.

• Only use or operate the mixer on solid, flat, level ground that is capable of supporting the weight of the mixer and its load to prevent the mixer

from tipping over.

• Do not attempt to move the mixer when it is loaded and/or in operation.

• This mixer is intended for the production of concrete, mortar, and plaster. It is not suitable for mixing flammable or explosive substances. Do not

use it in areas where fumes from paint, solvents, or flammable liquids pose a potential hazard.

Inspect Your Mixer

• C

heck your mixer before turning it on. Keep guards in place and in working order. Check all bolts, nuts, and screws for tightness before each use,

especially those securing guards and drive mechanisms. Vibration during mixing may cause these to loosen.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

CMS-14 Mortar Concrete Mixer

E&OE © Baumr-AG 4

• Form a habit of checking that all adjusting tools, shovels, hand trowels, and other equipment are removed from the mixer area before turning it

on.

• Replace damaged, missing, or failed parts before use. Warning labels carry important information, so replace any missing or damaged labels.

Dress Properly

• D

o not wear loose clothing, gloves, neckties, or jewellery (rings, wristwatches) as they can be caught in moving parts. Protective, electrically non-

conductive gloves and non-slip footwear are recommended when working. Wear protective hair coverings to contain long hair, preventing it from

getting caught in machinery. Wear a face or dust mask if the operation is dusty. Always wear safety goggles and/or face shields. Everyday

eyeglasses only have impact-resistant lenses and are not safety glasses.

Do Not Abuse the Cord

• N

ever carry the mixer by the cord or yank it to disconnect it from the socket.

• Keep the cord away from heat, oil, and sharp edges.

Extension Cords

• E

xtension cords must be no longer than 50 metres in length. The wire section must be 1.5mm² on 230V to allow sufficient current flow to the

motor. Improper use of extension cords may cause inefficient operation of the mixer, which can result in overheating and motor damage.

• Only extension cords compliant with H07RN-F specifications, intended for outdoor use, may be used. Avoid using loose and inadequately

insulated connections. Connections must be made with materials suitable for outdoor use. Ensure that any extension cord connections are dry

and safe. Lay the extension cord out carefully, avoiding liquids, sharp edges, and places where vehicles might run over it. Avoid allowing the

extension cord to become trapped underneath the mixer. Unroll it fully, as failure to do so could cause overheating and potentially lead to a fire.

Avoid Electrical Shock

• C

heck that the electrical circuit is adequately protected and that it corresponds with the power, voltage, and frequency of the motor.

• Do not plug or unplug the motor while standing in or around damp or wet ground. Do not use the mixer in wet or damp areas or expose it to rain.

• Prevent body contact with grounded surfaces such as pipes, radiators, stoves, and refrigerator enclosures.

• Ensure that your fingers do not touch the plug’s metal prongs when plugging or unplugging the mixer.

Keep Visitors and Children Away

• K

eep unauthorized persons away from the mixer.

• Do not allow children to handle or climb on or in the mixer.

Do Not Overreach

• M

aintain proper footing and balance at all times when loading or unloading the mixer.

• Never stand on the mixer. Serious injury could occur if the mixer tips or if moving parts are unintentionally contacted. Do not store anything above

or near the mixer where someone might stand on the mixer to reach them.

Avoid Injury from Unexpected Accidents

• K

eep hands clear of all moving parts. Do not place any part of your body or any tool, such as a shovel, into the drum during operation. While

operating, do not pass your hands through the clearance between the frame and support leg, or between the drum and support leg.

Do Not Force the Tool

• I

t will perform better and more safely at its designed rate. Always work within the rated capacity.

• Do not start the motor if the drum is fully loaded. Do not turn off the mixer while it is full of concrete.

• Do not use the mixer for any purpose for which it was not intended.

• The mixer is not to be towed by any vehicle.

Never Leave the Mixer Running Unattended

• D

o not leave the mixer until it has come to a complete stop.

Disconnect Power

• D

isconnect the mixer from the power supply when not in use, before moving it, making adjustments, changing parts, cleaning, or working on the

mixer. Consult the technical manual before servicing.

Maintain Your Mixer with Care

• C

lean the mixer immediately after use. Keep the mixer clean for optimal and safe performance.

• When maintaining this mixer, only use the manufacturer’s original replacement parts.

Protect the Environment

• T

ake leftover materials to an authorised collection point or follow the regulations of the country where the mixer is used. Do not discharge waste

into drains, soil, or water.

Store Idle Equipment

• When not

in use, the mixer should be stored in a dry location to prevent rust. Keep the mixer away from children and others not qualified to use it.

Electrical Connection

• E

nsure the motor is switched off before plugging it into the power supply. Do not connect either core to the earth pin.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

CMS-14 Mortar Concrete Mixer

E&OE © Baumr-AG 5

• The use of a Residual Current Device (RCD) or earth leakage trip on 230V electrical systems is recommended. If using an extension cable, plug

it directly into the RCD.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

CMS-14 Mortar Concrete Mixer

E&OE © Baumr-AG 6

Safety Symbols

The product may have safety warning labels attached to it, explained below. Understand the symbols on your

product and their meanings. If any stickers become unreadable, unattached etc., replace them.

Flammable Material Hazard

Flammable liquids, gases, or

substances etc may present.

Avoid ignition sources and open

flames. Danger of fire.

Read User Manual

Read and fully understand

product safety warnings,

operation, procedures etc before

using the product.

Use Hand Protection

Wear appropriate hand protection

and take due care as the product

or use of the product may present

hand hazards.

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be fatal.

Electrocution / Electrical Shock

Hazard

High voltage or high current

electricity may be present or

required by the product. Take

due care when handling electrical

products, cables, plugs and

leads. Electrical shock can be

fatal.

Toxic Fumes / Dust Hazard

Using the product or by-products

from use may produce fumes,

smoke or particles that could be

harmful if inhaled. Wear

appropriate breathing protection

and have adequate ventilation.

Explosive Material Hazard

Combustible liquids, gases, or

substances etc may be present.

Avoid ignition sources and open

flames. Danger of explosion.

Cutting / Amputation Hazard

The product may have blades,

edges or mechanical devices that

can cause severe cut injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Crush Hazard

The product may have blades,

edges or mechanical devices that

can cause severe crush injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Single Operator Only

The product must be operated by

a single person only. More than

one person operating the product

may introduce additional hazards.

Use Face Protection

Wear appropriate full-face

protection and take due care as

the product or use of the product

may present face and eye

hazards.

Use Foot Protection

Wear appropriate foot protection

and take due care as the product

or use of the product may present

foot hazards.

Use Eye / Ear / Head Protection

Wear appropriate eye and / or

ear and / or head protection and

take due care as the product or

use of the product may present

eye, hearing, and head hazards.

Running Hazard

Do not run on or near the product

as doing so may present a fall

hazard.

Diving Hazard

Do not dive into the product as

doing so may present a neck /

head injury hazard.

Adult Supervision Required

Always supervise children and

other users of a product to

prevent drowning or injury.

Skin Penetration / Puncture

Hazard

The product may produce

pressure, emit liquids or objects

that can cause severe injury to

fingers, limbs, blood etc. Take

due care when handling and

using the product.

Hot Surface Hazard

Be aware that the product may

produce high temperatures and

hot surfaces that can cause burn

injuries.

Flying Debris Hazard

Be aware that the product or use

of the product may present

hazards produced by flying

debris. Wear appropriate clothing

and protective devices.

Moving Parts Hazard

Be aware that the product

contains or uses mechanical

devices that move or rotate.

Always wait for moving parts to

stop fully before handling the

product, adjusting, maintenance

etc.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

CMS-14 Mortar Concrete Mixer

E&OE © Baumr-AG 7

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be fatal.

Pull Hazard

Be aware that the product

contains or uses mechanical

devices that can pull in objects

and can cause severe injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Slope / Fall Injury Hazard

Be aware that using the product

on sloping surfaces or in slippery

conditions may present additional

dangers from falls and contact

with blades, moving parts, hot

surfaces etc.

"Slam Dunk" Warning

Do NOT attempt "slam dunk"

manoeuvres as this may result in

severe injury due to falling,

product breakage or collapse etc.

Electrocution / Electrical Shock

Hazard - Outdoor

High voltage or high current

electricity may be present or

required by the product. Do NOT

use in rain, damp, or wet

conditions. Electrical shock can

be fatal.

Electrocution / Electrical Shock

Hazard - Disconnect

High voltage or high current

electricity may be present or

required by the product. Always

disconnect the product from the

electrical supply before handling

the product, adjusting,

maintenance etc.

Power Line Electrocution

Hazard

High voltage / high current power

lines may be present. Use

extreme caution to avoid contact

or interference with power lines.

Electrical shock can be fatal.

"Kick-Back" Hazard

High level of "kick-back" hazard

that can cause the machine to

suddenly rotate towards operator.

Kick-back injury can be fatal.

Winch Operator Position

Hazard

Do NOT stand between winch

and load. Do NOT use winch to

move people.

Winch Lift Hazard

Do NOT LIFT load vertically. Use

machine to PULL only.

Cable Hazard

Ensure that load bearing cable is

not kinked or knotted.

Winch Cable Hazard

Ensure that there is a minimum

number of cable coils on

winching mechanism.

Winch Hook Hazard

Carry hook to load – do NOT

throw or run.

Flash / Blinding Hazard

Wear appropriate eye protection

for welding. Direct exposure to

weld arcs may cause permanent

eye injury.

Laser Hazard

Laser may be in use – do NOT

look directly at laser or allow

others to.

Choking Hazard

Children under 8 yrs. Can choke

or suffocate on small parts. Adult

supervision required.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

CMS-14 Mortar Concrete Mixer

E&OE © Baumr-AG 8

Table of Contents

Safety ......................................................................................................................................................... 2

Safety Symbols ........................................................................................................................................................... 6

Parts Identification .................................................................................................................................... 9

Assembly ................................................................................................................................................. 10

Frame ....................................................................................................................................................................... 10

Wheels ...................................................................................................................................................................... 10

Drum ......................................................................................................................................................................... 11

Mixing Blades ........................................................................................................................................................... 11

Motor ......................................................................................................................................................................... 12

Legs .......................................................................................................................................................................... 12

Operation ................................................................................................................................................. 13

Loading ..................................................................................................................................................................... 13

Emptying ................................................................................................................................................................... 13

Maintenance ............................................................................................................................................. 14

Specifications .......................................................................................................................................... 15

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

CMS-14 Mortar Concrete Mixer

E&OE © Baumr-AG 9

Parts Identification

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

CMS-14 Mortar Concrete Mixer

Assembly

It is recommended that two people assist with the assembly.

Frame

1. Align the four holes of the main bracket with the support leg, then insert four M10x80 bolts from one side. On

the other side, place flat washers, lock washers, and nuts, then tighten with a wrench.

2. Insert the handles through the holes in the main bracket, then insert two M10x45 bolts from one side. On the

other side, place flat washers and nuts, then tighten with a wrench.

Wheels

1. Slide the wheels onto the axle. Place a washer against each wheel, then secure it with the locking pin.

2. Install the second wheel with the same process.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

CMS-14 Mortar Concrete Mixer

Drum

1. Attach the lower drum to the main bracket, place a large flat washer, and then tighten an M12x25 bolt with a

wrench.

2. Align the holes of the lower drum, the rubber gasket, and the upper drum. Place the rubber gasket and upper

drum onto the lower drum.

3. Insert six M8x16 bolts from one side. On the other side, place flat washers, lock washers, and nuts, then

tighten with a wrench.

Mixing Blades

1. Place the mixing blade inside the drum. Secure the mixing blade to the drum by inserting two M8x16 cross

screws from the outside, through the holes into the drum. A washer should be positioned inside, between the

drum and the blade. Secure the mixing blade on the inside using a flat washer, spring washer, and nut.

2. Install the second mixing blade in the same manner.

3. Tighten all the screws.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

CMS-14 Mortar Concrete Mixer

Motor

Place the motor assembly and gear cover onto the frame. Secure them with four M10x80 bolts, four flat washers

(Φ10), four spring washers (Φ10), and four M10 nuts.

Legs

1. Insert the four legs into the connecting pipe at the angle shown in the diagram and tighten them with two

M10x120 bolts and two M10 locking nuts.

2. Insert the connecting tube into the fixed sleeve at the bottom of the frame.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

CMS-14 Mortar Concrete Mixer

Operation

Loading

•

Completely unwind the extension cord and connect it to the concrete mixer before plugging it into the power

supply.

•

Always start the mixer before loading the drum. Load the drum while it is rotating.

•

Do not throw material into the mixer, as this may cause it to stick to the back of the drum. Instead, trickle it

steadily over the ram.

For best results, proceed as follows:

1. Add the required amount of gravel into the drum.

2. Add the required amount of cement into the drum.

3. Add the required amount of sand into the drum.

4. Pour the required amount of water into the drum.

Emptying

Do not turn the mixer off while it is full. Empty the drum while it is rotating

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

CMS-14 Mortar Concrete Mixer

Maintenance

ATTENTION: Surface corrosion will occur on metal surfaces over time and the rate of oxidation depends

on factors such as proximity to the ocean and humidity or condensation of water vapour on metal

surfaces. To mitigate this, WD40 can be used to remove surface corrosion then, when applied

periodically, it will prevent rust from forming.

Before starting any maintenance or repairs, stop the engine or switch off the motor, and disconnect it

from the main power supply.

Upon completion of maintenance, ensure the mixer functions correctly and that all guards are properly

fitted.

•

Never put your hands inside the drum while it is rotating.

•

Thoroughly clean the mixer at the end of each day’s operation. Keep your mixer clean. Even the slightest

trace of material left in the drum will harden and attract more material each time you use it, eventually

rendering the machine unusable. Dried cement should be scraped out of the drum. Do not throw bricks into

the mixer drum to clean it out.

•

Do not hit the drum with a shovel, hammer, or other tools to break up accumulations of dried cement mix, as

this may cause damage to the mixer.

•

Do not pour or spray water directly over the motor cover, especially near the openings.

•

Wipe off any external material on the motor. Do not use petrol, turpentine, lacquer, paint thinner, dry-

cleaning fluids, or similar products.

•

The wiring diagram and parts schematic in this manual are for reference purposes only. Neither the

manufacturer nor the distributor makes any representation or warranty to the buyer that they are qualified to

make any repairs to the product or to replace any parts of the product. Only qualified technicians should

repair the mixer. Any maintenance and repairs to the electrical components must be undertaken by a

qualified electrician.

•

Parts marked with a circle should only be fitted by a qualified electrician.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

CMS-14 Mortar Concrete Mixer

Specifications

Drum Capacity 140L

Voltage 240V

Power (Watts) 550W

Oil Type 10W-30 | 10W-40 | 15W-40

Drum Speed 32 RPM

Body Material Steel

Finish Powder-coated

Power Type Corded Electric

Drum Diameter 566mm

Wheels 10-inch rubber

Power Plug 10A Australian Standard

Note: Requires assembly

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Some experts believe that the incorrect or prolonged use of almost any

product may cause serious injury or death. To help reduce your risk of

serious injury or death, refer to the information below. For more information,

see www.datastreamserver.com/safety



Consult all documentation, packaging,

and product labelling before use. Note

that some products feature

documentation available online. It is

recommended to print and retain the

documentation.



Before each use, check the product for

loose/broken/damaged/missing parts,

wear, or leaks (if applicable). Never use a

product with

loose/broken/damaged/missing parts,

wear, or leaks.



Products must be inspected and serviced

(if applicable) by a qualified technician

every 6 months. This is based on

average residential use by persons of

average size and strength, and on a

property of average metropolitan size.

Use beyond these recommendations may

require more frequent

inspections/servicing.



Ensure that all users of the product have

completed a suitable industry recognised

training course before being allowed

access to the product.



The product has been supplied by a general merchandise

retailer that may not be familiar with your specific

application or description of application. Be sure to attain

third-party approval from a qualified specialist for your

application before use, regardless of any assurances from

the retailer or its representatives.



This product is not intended for use where fail-safe

operation is required. As with any product (for example,

automobile, computer, toaster), there is the possibility of

technical issues that may require the repair or

replacement of parts, or the product itself. If the possibility

of such failure and the associated time it may take to

rectify could in any way inconvenience the user, business,

or employee, or financially affect the user, business, or

employee, then the product is not suitable for your

requirements. This product is not intended for use where

incorrect operation or a failure of any kind, including but

not limited to, a condition requiring product return,

replacement, parts replacement, or service by a

technician may cause financial loss, loss of employee

time or an inconvenience requiring compensation.



If this product has been purchased in error when

considering the information presented here, contact the

retailer directly for details of their returns policy, if

required.

diagrams, or images may be reproduced or transmitted in any form or by any means, electronic or

mechanical, including photocopying, scanning, or recording, or any information storage and retrieval system,

without express permission or consent from the publisher.

BAUMR-AG TOLCCMBM1C4A Portable Cement Mixer Pedestal Stand and Solid Rubber Wheels for Reliable Mixing Performance

Product's Documents

Product manual

Specifications

BAUMR-AG TOLCCMBM1C4A Questions and Answers