POWERING PEOPLE SINCE 1886
and Westinghouse are trademarks of Westinghouse Electric Corporation. All Rights Reserved.
MAINTENANCE-FREE AGM BATTERY
SAFETY DATA SHEET
WHB75 AH
Section 1: Product Identification
Product Name
Maintenance Free Valve Regulated Lead Acid Battery: DJW, DJM, DJ, LHT, LHTF, PLX, PLH, PLC, XP, LP, LPC, LPL, LPF, LPX, LPS, FT,
LHR Series.
Common Synonyms Sealed Lead Acid Battery, Non-dangerous battery, VRLA Lead Acid Batteries, VRLA Battery.
DOT Description Battery, wet, non-spillable, electric storage battery.
Chemical Family Electrical Battery Standby.
Manufacturer’s Name Westinghouse Residential Pumps
Address 4400 Easton Commons, Suite 250, Columbus Ohio, 43219
Phone Number 1-833-594-0444
Email support@respumps.westinghouse.com
Date Issued January 01, 2024
Section 2: Hazards Identification
HEALTH ENVIRONMENTAL PHYSICAL
Acute Toxicity Aquatic Chronic 1 Explosive Chemical, Division 1.3
(Oral/Dermal/Inhalation) Category 4 Aquatic Acute 1
Skin Corrosion/Irritation Category 1A
Eye Damage Category 1
Reproductive Category 1A
Carcinogenicity (lead compounds) Category 1B
Carcinogenicity (arsenic) Category 1A
Carcinogenicity (acid mist) Category 1A
Specific Target Organ Category 2
Toxicity (repeated exposure)
and Westinghouse are trademarks of Westinghouse Electric Corporation. All Rights Reserved. Page 2
Section 2: Hazards Identification
GHS LABEL
HEALTH ENVIRONMENTAL PHYSICAL
Hazard Statements: DANGER! Precautionary Statements
Causes severe skin burns and serious eye damage. Wash thoroughly after handling.
May damage fertility or the unborn child if ingested or inhaled. Do not eat, drink or smoke when using this product.
May cause cancer if ingested or inhaled. Wear protective gloves/protective clothing, eye protection/face protection.
Causes damage to central nervous system, blood and kidneys
through prolonged or repeated exposure.
Avoid breathing dust/fume/gas/mist/vapors/spray.
May form explosive air/gas mixture during charging. Use only outdoors or in a well-ventilated area.
Extremely flammable gas (hydrogen).
Contact with internal components may cause irritation or severe burns. Avoid contact with
internal acid.
Explosive, fire, blast, or projection hazard. Irritating to eyes, respiratory system, and skin.
May cause harm to breast-fed children. Harmful if swallowed,
inhaled, or contact with skin. Causes skin irritation, serious eye
damage.
Obtain special instructions before use.
Do not handle until all safety precautions have been read and understood
Avoid contact during pregnancy/while nursing
Keep away from heat./sparks/open flames/hot surfaces. No smoking.
Other Hazards
Mechanical
VRLA Batteries can be heavy. Correct manual handling techniques and/or mechanical lifting aides (e.g. Fork Lift
Truck) must be used.
Electrical
VRLA Batteries can contain large amounts of electrical energy which can give very high discharge currents and
severe electrical shock if the terminals are short circuited.
Chemical
-The VRLA Battery presents no chemical hazards during the normal operation provided the recommendations for
handling, storage, transport and usage are observed.
-VRLA Batteries emit hydrogen gas which is highly flammable and will form explosive mixtures in air from approx.
4% to 76%. This can be ignited by a spark at any voltage, naked flames or other sources of ignition.
-If the battery is broken and the internal components exposed, hazards may exist which require
careful attention.
Section 3: Hazardous Ingredients/ Identity Information
Components Approx. % by Wt. CAS Number
Air Exposure Limits (
μg/m3)
LD50
ORAL (mg/kg)
ACGIH TLV OSHA NIOSH
Inorganic Lead/Lead
Compounds
65%-75% 7439-92-1 150 50 10 --
Tin <0.5% 7440-31-5 2000 2000 -- --
Calcium <0.1% 7440-70-2 -- -- -- --
Dilute Sulfuric Acid ~20% 664-93-9 1000 1000 1000 2.14
Fiberglass Separator ~5% 65997-17-3 -- -- -- --
Case Material:
Acrylonitrile
Butadiene Styrene
(ABS)
~5% 9003-56-9 -- -- -- --
and Westinghouse are trademarks of Westinghouse Electric Corporation. All Rights Reserved. Page 3
Section 4: First Aid Measures For Acute Exposure
This information is of relevance only if the VRLA Battery has suered damage, is broken and persons have direct contact with the internal components.
Plate Grids and
Active materials
Inhalation Remove the person from exposure to fresh air. Seek advice from a medical doctor
Ingestion
Wash out mouth with water and give plenty of water to drink. Do not induce vomiting. Seek advice from a
medical doctor
Skin Contact
Wash o with plenty of water and soap to prevent accidental ingestion or inhalation. Seek medical advice if pain
or rash does not reduce
Eye Contact
Immediately irrigate with eyewash solution or clean water for at least 10 minutes, holding the eyelids apart.
Then take the person to hospital without further delay
Self-protection for
the first aider
Eye protection (safety glasses or face shield), and heavy-duty gloves are required. In case of inhalation, a face
mask or respirator may be required.
Battery Electrolyte
SPEED IS ESSENTIAL - OBTAIN IMMEDIATE MEDICAL ATTENTION.
Inhalation
Remove the person from exposure to fresh air. If the person continues to feel unwell seek advice from a medical
doctor.
Ingestion
Wash out mouth with water and give plenty of water to drink. Do not induce vomiting. If the person continues to
feel unwell seek advice from a medical doctor.
Skin Contact
Drench with large quantities of water. Remove contaminated clothing and place in water to dilute the acid.
Continue to wash the aected area for at least 10 minutes. Seek advice from a medical doctor
Eye Contact
SPEED IS ESSENTIAL - OBTAIN IMMEDIATE MEDICAL ATTENTION
Immediately irrigate with eyewash solution or clean water for at least 10 minutes, holding the eyelids apart.
Then take the person to hospital without further delay.
Self-protection for
the first aider
Eye protection (safety glasses or face shield), and heavy-duty gloves are required. In case of inhalation, a face
mask or respirator may be required.
Case Material
Inhalation
Material can burn in a fire with toxic smoke and decomposition products.
Upon inhalation of decomposition products, keep patient calm, remove to fresh air, and seek advice from a
medical doctor. If a large quantity is inhaled take the person to hospital.
Note to physician: Treat according to symptoms (decontamination, vital functions), no known specific antidote.
Ingestion
Wash out mouth with water and give plenty of water to drink. Do not induce vomiting. If the person continues to
feel unwell seek advice from a medical doctor.
Skin Contact
Areas aected by molten material should be quickly placed under cold running water and a sterile protective
dressing applied. Seek advice from a medical doctor.
Eye Contact
May cause irritation or injury due to mechanical action and traces of Battery Electrolyte. Immediately irrigate
with eyewash solution or clean water for at least 10 minutes, holding the eyelids apart. Then take the person to
hospital without further delay
Self-protection for
the first aider
Eye protection (safety glasses or face shield), and disposable gloves are required. In case of inhalation, a face
mask or respirator may be required.
Separator Material
Inhalation Remove patient from exposure to fresh air. If irritation persists, seek advice from a medical doctor.
Ingestion
Wash out mouth with water and give plenty of water to drink. Do not induce vomiting. If the person continues to
feel unwell seek advice from a medical doctor.
Skin Contact
After contact with skin, wash immediately with plenty of soap and water. If irritation persists, seek advice from
a medical doctor.
Eye Contact
May cause irritation or injury due to mechanical action and traces of Battery Electrolyte. Immediately irrigate
with eyewash solution or clean water for at least 10 minutes, holding the eyelids apart. Then take the person to
hospital without further delay
Self-protection for
the first aider
Eye protection (safety glasses or face shield), and disposable gloves are required. In case of inhalation, a face
mask or respirator may be required.
and Westinghouse are trademarks of Westinghouse Electric Corporation. All Rights Reserved. Page 4
Section 5: Fire-Fighting And Explosion Hazard Measures
VRLA batteries
Flash Point: N/A
General
Information:
Explosion Hazard
VRLA Batteries emit hydrogen gas which is highly flammable and will form explosive mixtures in air from
approx. 4% to 76%. This can be ignited by a spark at any voltage, naked flames or other sources of ignition.
Batteries in use will be part of an electrical circuit and must be isolated from the power source before
attempting to put out a fire. Switch the power OFF before disconnecting the batteries from the power source.
Damaged batteries may expose negative plates, grey in colour, which may ignite if allowed to dry out. These
plates may be wetted down with water after the battery has been removed from all electrical circuits.
Suitable
Extinguisher types
CO2; Foam; Dry Powder.
Unsuitable
Extinguisher types
Water extinguishers must never be used to put out an electrical fire.
Hazardous
combustion &
decomposition
products
Carbon monoxide, Sulphur Dioxide, Sulphur Trioxide, Lead fume and vapour, toxic fumes from decomposition of
battery case materials.
Advice for fire-
fighters
Full face visor or safety goggles; Respiratory equipment or self-contained breathing apparatus (SCBA); Full acid
resistant protective clothing must be worn in fire-fighting conditions.
Section 6: Accidental Release Measures
This information is of relevance only if the VRLA Battery has suered damage and is broken.
VRLA Battery
VRLA batteries are designed to be safe to handle and not to leak battery electrolyte under normal conditions.
In case of accidental damage heavy-duty gloves are required to pick-up the battery to protect against unseen
electrolyte leakage
Plate Grids and
Active Materials
Personal
Precautions
Eye protection (safety glasses or face shield), and heavy-duty gloves are required. If the material is wet, a face
mask or respirator is not required If the material is dry, a face mask or respirator is required
Clean-up Methods
Large, solid pieces may be picked up and bagged for recycling. Never use a brush to sweep up debris; it may
create Lead-dust in the air. Wet clean the spill area to remove all traces of debris. Battery debris and cleaning
materials must be collected and placed in an inert sealed container (e.g. self-seal plastic bag or bucket) for
disposal.
Environmental
Precautions
Do not allow material to enter a watercourse. Exposed Lead materials must be placed in an inert sealed
container (e.g. self-seal plastic bag or bucket) for disposal.
Battery Electrolyte
Personal
Precautions
Ensure suitable, acid resistant personal protective clothing (including heavy-duty gloves, safety glasses and
respiratory protection) is worn during removal and clean-up of spillages.
Clean-up Methods:
Small spillages
Neutralise and absorb the spillage using soda ash, sodium bicarbonate (available from supermarkets), sodium
carbonate or calcium carbonate powder. Wet clean the spill area to remove all traces of debris. Battery debris
and cleaning materials must be collected and placed in an inert sealed container (e.g. self-seal plastic bag or
bucket) for disposal.
Clean-up Methods:
Large spillages
Large amounts of electrolyte spillage are unlikely with VRLA batteries since the electrolyte is fully absorbed
in the active materials and separator. Bund the spillage area using dry sand, earth, sawdust or other inert
material. Neutralise the electrolyte using soda ash, sodium bicarbonate (available from supermarkets), sodium
carbonate or calcium carbonate powder. Wet clean the spill area to remove all traces of debris and electrolyte.
Cleaning materials must be collected and placed in an inert sealed container (e.g. self-seal plastic bag or bucket)
for disposal.
Environmental
Precautions
Battery electrolyte must not be allowed to enter any drains or sewage system or water course.
Case Material Clean-up Methods Assume battery case material is contaminated and proceed as for Plate Grids and Active Materials above.
Separator Material Clean-up Methods Assume battery case material is contaminated and proceed as for Plate Grids and Active Materials above.
and Westinghouse are trademarks of Westinghouse Electric Corporation. All Rights Reserved. Page 5
Section 7: Handling and Storage
Handling
Unless involved in recycling operations, do not breach the casing or empty the contents of the battery. Handle carefully and avoid
tipping, which may allow electrolyte leakage. There may be increasing risk of electric shock from strings of connected batteries.
Keep containers tightly closed when not in use. If battery case is broken, avoid contact with internal components.
Keep vent caps on and cover terminals to prevent short circuits. Place cardboard between layers of stacked automotive batteries to
avoid damage and short circuits.
Keep away from combustible materials, organic chemicals, reducing substances, metals, strong oxidizers and water. Use banding or
stretch wrap to secure items for shipping.
Storage
Store batteries in cool, dry, well-ventilated areas with impervious surfaces and adequate containment in the event of spills. Batteries
should also be stored under roof for protection against adverse weather conditions. Separate from incompatible materials. Store and
handle only in areas with adequate water supply and spill control. Avoid damage to containers. Keep away from fire, sparks and heat.
Keep away from metallic objects could bridge the terminals on a battery and create a dangerous short-circuit.
Charging
There is a possible risk of electric shock from charging equipment and from strings of series connected batteries, whether or not being
charged. Shut-o power to chargers whenever not in use and before detachment of any circuit connections. Batteries being charged
will generate and release flammable hydrogen gas.
Charging space should be ventilated. Keep battery vent caps in position. Prohibit smoking and avoid creation of flames and sparks
nearby.
Wear face and eye protection when near batteries being charged.
Section 8: Exposure Control / Personal Protection
VRLA Battery
Control Parameters
There are no special control parameters for the handling, storage, installation of VRLA Batteries.
VRLA Batteries emit hydrogen gas which is highly flammable and will form explosive mixtures in air from approximately 4% to 76%.
Never install VLRA Batteries in a gas- tight enclosure during storage, transport or usage.
Exposure Control There are no special exposure controls for the handling, storage, installation or use of VRLA Batteries.
Personal Protection
When there is no evidence of damage or visible traces of liquid (electrolyte) or solid deposits on the batteries they may be handled
safely without extra personal protective equipment.
Ensure electrical insulation equipment is used when installing batteries. (e.g. insulated mats and covers; insulated tools)
Remove ALL metallic objects from the person when working with VRLA Batteries: e.g. Jewellery (rings, watches, bracelets, necklaces),
pens, torches, etc. Where there are signs of damage or liquid (electrolyte) or solid deposits, rubber gloves and acid resistant clothing
must be worn when handling the batteries and aected packaging to protect against the eects of any electrolyte that may be
present.
If it is suspected that free electrolyte is present, then safety glasses must be worn, and if large amounts are present, chemical goggles
or face shield should be used.
UL CAUTIONARY
STATEMENT
“Warning: Risk of fire, explosion, or burns. Do not disassemble; heat above 50°C; or incinerate”.
and Westinghouse are trademarks of Westinghouse Electric Corporation. All Rights Reserved. Page 6
Section 9: Physical and Chemical Properties
VRLA Battery
The main components are listed in SECTION 2 above
The undamaged product is a manufactured article in an inert plastic (ABS) case, which will burn if subjected to high temperatures or
sources of ignition. Some battery types are made with Flame Retardant ABS cases, see technical specification. These batteries carry
the sux ‘FR’ after the battery type.
The information below refers to the physical and chemical properties of the main VRLA Battery components and substances. This information is published for
reference only.
Plate Grids and
Active materials
Appearance Safety-related data
Form Solid Solidification point 327 °C
Colour Grey or brown Boiling point 1740 °C
Odour Odourless Solubility in water Very low (0.15mg/l)
Solubility in acid or alkaline
solutions
Yes, dependant on the strength
of solution.
Density (at 20°C) 11.35 g/cm3
Vapour pressure (at 20°C) Undetectable
Battery Electrolyte
Form Liquid Solidification point -35 to -60 °C
Colour Colourless Boiling point Approx. 108 to 114 °C
Odour Odourless Solubility in water Complete
Density (at 20°C) Variable up to 1.350 g/cm3
Vapour pressure (at 20°C) 10-20 mmHg
Case Material
Appearance
Form Solid Softening point > 100 °C
Colour Grey or black Flash Point >330 °C
Odour Slight Odour Solubility in water Insoluble
Solubility in other solvents
Soluble in polar solvents,
aromatic solvents, chlorinated
hydrocarbons.
Density (at 20°C) 1.07-1.4 g/cm3
Vapour pressure (at 20°C) Undetectable
Separator Material
Form Fibrous material Solidification point 820°C
Colour White Boiling point >2500°C
Odour Odourless Solubility in water Insoluble
Density (at 20°C) 2.23g/cm3
Vapour pressure (at 20°C) Undetectable
and Westinghouse are trademarks of Westinghouse Electric Corporation. All Rights Reserved. Page 7
Section 10: Stability and Reactivity
VRLA Battery Stability Within the operational temperature range -20 to +50 °C the undamaged product is stable
Plate Grids and
Active materials
Materials & Conditions to Avoid
Powdered Lead reacts violently with fused ammonium nitrate and sodium acetylide. Reacts
violently when in contact with chlorine trifluoride.
Battery Electrolyte
Possibility of Hazardous
Reactions
Dilution of the higher concentrated grades with water may liberate excessive heat.
Highly reactive with metals and organic materials.
On contact with metals, may generate hydrogen which forms explosive mixtures with air.
Destroys organic materials such as cardboard, wood, textiles, etc.
Hazardous Decomposition
Product(s)
Sulphur oxides
Case Material
Materials & Conditions to Avoid
To avoid thermal decomposition, do not overheat.
Starts to decompose at temperatures >275°C
Powerful oxidising agents.
Hazardous decomposition
products
Monomers, other degradation products, traces of hydrogen cyanide.
Separator Material
Stability Stable material.
Materials & Conditions to Avoid Incompatible with Hydrofluoric acid and concentrated Sodium Hydroxide.
Hazardous decomposition
products
No hazardous polymerisation expected.
and Westinghouse are trademarks of Westinghouse Electric Corporation. All Rights Reserved. Page 8
Section 11: Toxicological Information
This information is of relevance only if the VRLA Battery has suered damage and is broken.
VRLA Battery
This information does not apply to the undamaged VRLA Battery. It is of relevance if the battery is
broken and the components are released to the environment
Exposure limits may vary according to national law and regulations.
Plate Grids: Metallic
Lead, Lead alloys.
Acute Toxicity
Toxic by ingestion or inhalation
Chronic poison
Lead is a poison that aects virtually every system in the body
Symptoms include fatigue, headaches, constipation, aching bones and muscles, gastrointestinal
tract disturbances and reduced appetite
Symptoms include fatigue, headaches, constipation, aching bones and muscles, gastrointestinal
tract disturbances and reduced appetite
Active materials:
Lead dioxide.
Acute Toxicity Toxic by ingestion or inhalation
Chronic exposure to Lead compounds may lead to a build-up of Lead in the body, giving rise to a
variety of health problems, including anaemia, kidney and liver damage, impaired eyesight, memory
loss and CNS2 damage
Battery Electrolyte
Corrosive Corrosive, the more concentrated solutions can cause serious burns to the mouth, eyes and skin
Harmful by ingestion and through skin contact
Inhalation
Mist is a severe irritant to the respiratory tract. Fluid build-up on the lung (pulmonary oedema) may
occur up to 48 hours after exposure and could prove fatal
Ingestion
Will immediately cause severe corrosion of and damage to the gastrointestinal tract
Skin Contact
Causes severe chemical burns
Eye Contact
Risk of serious damage to eyes. Causes severe burns. May cause prolonged or permanent damage
or even total loss of sight. Mist will cause irritation
Case Material
According to information available the product is not harmful to health provided it is correctly
handled and processed according to the given recommendations.
Separator Material
Based on animal implantation and epidemiologic studies glass microfibers are thought to have
some limited carcinogenic potential and as such are designated as Group 2B materials (IARC, US).
The material should be treated as a category 3 carcinogen (Europe). Limited evidence of carcinogenic
eect.
and Westinghouse are trademarks of Westinghouse Electric Corporation. All Rights Reserved. Page 9
Section 12: Ecological Information
This information is of relevance only if the VRLA Battery has suered damage and is broken.
VRLA Battery
This information does not apply to the undamaged VRLA Battery. It is of relevance if the battery is
broken and the components are released to the environment.
Plate Grids and
Active materials
Metallic Lead, Lead alloys and
Lead dioxide
Chemical and physical treatment is required for the elimination of Lead from water. Waste water
containing Lead must not be disposed of in an untreated condition.
Ecotoxicity
Lead metal in massive form is not classified as hazardous to the aquatic environment, due to its low
solubility and rapid removal from the water column. Inorganic lead compounds are considered to be
acutely toxic in the environment and also to present a long- term hazard to aquatic organisms.
Eect in the aquatic
environment
Toxicity for fish: 96 h LC 50 > 100 mg/l
Toxicity for daphnia: 48 h EC 50 > 100 mg/l
Toxicity for alga: 72 h IC 50 > 10 mg/l
Battery Electrolyte
Ecotoxicity
In order to avoid damage to the sewerage system, the acid has to be neutralised by means of soda
ash, sodium bicarbonate or sodium carbonate before disposal.
Ecological damage is possible by change of pH. The electrolyte solution reacts with water and
organic substances, causing damage to flora and fauna.
The electrolyte may also contain components of Lead that can be toxic to aquatic environments.
Persistence and Degradation Remains indefinitely in the environment as sulphate.
Case Material
Elimination information No data available: insoluble in water
Behaviour and environmental
fate
Due to the consistency of the product, and its insolubility in water, it will apparently not be bio-
available.
Separator Material
No data available: insoluble in water
Not thought to pose any risk to the environment.
and Westinghouse are trademarks of Westinghouse Electric Corporation. All Rights Reserved. Page 10
Section 13: Disposal Considerations
VRLA Battery
Europe
Spent (used) VRLA Batteries are subject to the requirements of the Batteries Directive 2006/66/EC on batteries and
accumulators and waste batteries and accumulators. Spent (used) VRLA Batteries MUST be sent for recycling through
an authorised contractor at the end-of-life.
The WEEE Directive 2002/96/EC (Waste Electrical and Electronic Equipment) applies. Spent (used) VRLA Batteries MUST
be removed from electrical and electronic equipment at the end-of-life.
Worldwide
VRLA batteries contain inorganic Lead compounds and Sulphuric Acid which are damaging to the environment.
Spent (used) batteries must be disposed of in an environmentally friendly manner in accordance with local national
laws and regulations.
VRLA batteries must not be dismantled, burnt or incinerated as a means of disposal.
At the end of life VRLA batteries may still be electrically ‘live’ and contain a large amount of electrical energy. The same
care and attention to safe handling should be taken as when handling new batteries. Particular care must be taken to
avoid short-circuiting the battery terminals.
Plate Grids and
Active materials
Europe
Worldwide
Metallic Lead and active materials (Lead Oxides) must be recycled.
Disposal must be carried out in accordance with the European Hazardous Waste Directive 2008/98/EC.
Battery Electrolyte
Europe
Disposal must be carried out in accordance with the European Hazardous Waste Directive 2008/98/EC on the
protection of the environment through criminal law
Worldwide Disposal should be in accordance with local, state or national legislation.
General
Battery electrolyte is dilute Sulphuric Acid, the strength of which depends on the state of charge of the batteries. It
must be neutralised before disposal. See SECTION 6 for clean-up and disposal advice.
Case Material
Do not dispose of this product into sewers, any ocean or water course in order to prevent marine animals and birds
from ingesting.
Recycling is encouraged.
Disposal by controlled incineration or source landfill in accordance with local national laws and regulations may be
acceptable.
Separator Material
Constitutes a special waste by virtue of hazardous substance content.
Dispose of via approved landfill site. Disposal by controlled source landfill in accordance with local national laws and
regulations may be acceptable.
and Westinghouse are trademarks of Westinghouse Electric Corporation. All Rights Reserved. Page 11
Section 14: Transport Information
Proper Shipping Name Batteries, wet, non-spillable
Wet, non-spillable batteries do not need to be shipped and transported as fully-regulated Class 8 Corrosive hazardous materials / dangerous goods when
tested, packaged and marked in accordance with the following regulations:
U.S. DOT
Our non-spillable lead acid batteries are under the U.S. Department of Transportation’s (DOT) hazardous materials regulations but are
excepted from these regulations since they meet all of the following requirements found at 49 CFR 173.159(f) and 49 CFR 173.159a
The batteries are excepted from regulation if they have been tested in accordance with the vibration and pressure dierential tests
found in 49 CFR 173.159(f) and “rupture test” found at 49 CFR 173.159a;
When oered for transport, the batteries must be protected against short circuits and securely packaged in accordance with 49
CFR 173.159a; and
The batteries and outer packaging must be marked NON-SPILLABLE BATTERY or NON-SPILLABLE as required by 49 CFR 173.159a
ADR / RID Land Transport: Not applicable
IATA Dangerous Goods
Regulations DGR
Excepted from the dangerous goods regulations because the batteries meet the requirements of Packing Instruction 872 and
Special Provisions A67 of the International Air Transportation Association (IATA 65th version) Dangerous goods Regulations and
International Civil Aviation Organization (ICAO) Technical Instructions. Battery Terminals must be protected against short circuits.
The words “NOT RESTRICTED”, SPECIAL PROVISION A67” must be provided on an airway bill when air waybill is issued.
IMDG
Excepted from the dangerous goods regulations for transport by sea because the batteries meet the requirements of Special
Provision 238 of the International Maritime Dangerous Goods (IMDG CODE). Battery terminals must be protected against short
circuits.
IMO Non-Hazardous for Sea Transport: Non-hazardous for sea transport.
If the regulations listed above are not met, then Batteries, wet, nonspillable (UN2800) are regulated as Class 8 Corrosive hazardous materials / dangerous
goods by the U.S. Department of Transportation (DOT) and international dangerous goods regulatory authorities pursuant to the IATA Dangerous Goods
Regulations and IMDG Code.
Section 15: Regulatory Information
VRLA Battery Required Markings
Europe
Crossed-out wheeled bin indicating “SEPARATE COLLECTION” for all batteries and accumulators. Not
to be disposed of with general domestic, commercial or industrial waste. Ref: The Batteries Directive
2006/66/EC
Europe
The Pb symbol indicates the heavy metal content of the battery and enables the Lead-Acid battery to
be sorted for recycling. Ref: The Batteries Directive 2006/66/EC.
Worldwide
The International Recycling Symbol, required by law in many countries world-wide to facilitate the
identification of secondary batteries and accumulators for recycling. Ref: IEC 61429 : 1995, Marking
of secondary cells and batteries with the International Recycling Symbol ISO 7000-1135
U.S. Proposition 65
Warning: Battery posts, terminals and related accessories contain lead and lead compounds,
chemicals known to the State of California to cause cancer and reproductive harm. Batteries also
contain other chemicals known to the State of California to cause cancer. Wash hands after handling.
Europe EC Directives
Directive 2006/66/EC, on batteries and accumulators and waste batteries and accumulators.
Paragraph (Recital) 29 states: “Directive 2002/95/EC of the European Parliament and of the Council
of 27 January 2003 on the restriction of the use of certain hazardous substances in electrical and
electronic equipment does not apply to batteries and accumulators used in electrical and electronic
equipment.”
and Westinghouse are trademarks of Westinghouse Electric Corporation. All Rights Reserved. Page 12
Section 15: Regulatory Information
Germany
VwVwS Annex reference Water hazard class (WGK) 2, hazard to waters (Classification according to VwVwS, Annex 4)
12th Ordinance Implementing the Federal
Immission Control Act - 12.BImSchV
Is not subject of the 12. BlmSchV (Hazardous Incident Ordinance)
Netherlands
SZW-lijst van kankerverwekkende stoen None of the components are listed
SZW-lijst van mutagene stoen None of the components are listed
NIET-limitatieve lijst van voor de voortplanting giftige stoen – Borstvoeding Lead is listed
NIET-limitatieve lijst van voor de voortplanting giftige stoen – Vruchtbaarheid Lead is listed
NIET-limitatieve lijst van voor de voortplanting giftige stoen – Ontwikkeling Lead is listed
SARA 302 Extremely hazardous substance
Chemical name CAS number
Reportable Quantity
(pounds)
Threshold planning
quantity (pounds)
Threshold planning
quantity, lower value
(pounds)
Threshold planning
quantity, upper value
(pounds)
Sulphuric Acid 7664-93-9 1000 1000
SARA 311/312 Hazardous chemical No
US federal regulations
TSCA Section 12(b) Export Notification
(40 CFR 707, Subpt. D)
Not regulated.
CERCLA Hazardous Substance List (40
CFR 302.4)
Lead (CAS 7439-92-1): Listed.
Sulphuric Acid (CAS 7664-93-9): Listed.
SARA 304 Emergency release notificatio Sulphuric Acid (CAS 7664-93-9): Listed.
OSHA Specifically Regulated Substances
(29 CFR 1910.1001- 1050)
Lead (CAS 7439-92-1):
Reproductive toxicity
Central nervous system
Kidney
Blood
Acute toxicity
Superfund Amendments and
Reauthorization Act of 1986 (SARA)
Hazard categories:
Immediate Hazard – No
Delayed Hazard - No
Fire Hazard - No
Pressure Hazard - No
Reactivity Hazard - No
Denmark
Classification remarks Emergency management guidelines for the storage of flammable liquids must be followed
Recommendations Danish Regulation
Young people below the age of 18 years are not allowed to use the product. Pregnant/breastfeeding women
working with the product must not be in direct contact with the product
and Westinghouse are trademarks of Westinghouse Electric Corporation. All Rights Reserved. Page 13
Section 15: Regulatory Information
SARA 313 (TRI reporting)
Chemical name CAS number % by wt.
Lead 7439-92-1 65%-75%
Sulphuric Acid 7664-93-9 ~20%
Section 16: Other Information
HMIS®ratings
Health: 0
Flammability: 1
Physical hazard: 0
Health: 0
NFPA ratings
NFPA ratings
Flammability: 1
Instability: 0
Disclaimer The information in the sheet was written based on the best knowledge and experience currently available.
Issue date January 01, 2024
Other federal regulations
Clean Air Act (CAA) Section 112 Hazardous Air Pollutants (HAPs) List Lead (CAS 7439-92-1)
Clean Air Act (CAA) Section 112(r) Accidental Release Prevention (40 CFR 68.130) Sulphuric Acid (CAS 7664-93-9)
Safe Drinking Water Act (SDWA) Not regulated.
Drug Enforcement Administration (DEA). List 2, Essential Chemicals (21 CFR
1310.02(b) and 1310.04(f)(2) and Chemical Code Number
Sulphuric Acid (CAS 7664-93-9) : 6552
Drug Enforcement Administration (DEA). List 1 & 2 Exempt Chemical Mixtures
(21 CFR 1310.12(c))
Sulphuric Acid (CAS 7664-93-9): 20%WV
DEA Exempt Chemical Mixtures Code Number Sulphuric Acid (CAS 7664-93-9): 6552
US - California Proposition 65 - CRT: Listed date/Carcinogenic substance
Lead (CAS 7439-92-1) Listed: October 1, 1992
Sulphuric Acid (CAS 7664-93-9) Listed: March 14, 2003
US - California Proposition 65 - CRT: Listed date/Developmental toxin
Lead (CAS 7439-92-1) Listed: February 27, 1987
US - California Proposition 65 - CRT: Listed date/Female reproductive toxin
Lead (CAS 7439-92-1) Listed: February 27, 1987
US - California Proposition 65 - CRT: Listed date/Male reproductive toxin
Lead (CAS 7439-92-1) Listed: February 27, 1987
US. California. Candidate Chemicals List. Safer Consumer Products
Regulations (Cal. Code Regs, tit. 22, 69502.3, subd.(a))
Lead (CAS 7439-92-1)
Tin (CAS 7440-31-5)
Sulphuric Acid (CAS 7664-93-9)
