Smeg SPR36UIMAN Range Matt Black

Installation Manual EN - Transcript

• Page 1 - English - : Table of Contents EN 1Installation 9 11 Product dimensions 9 12 Unpacking moving and positioning the range 12 13 Electrical connection 13 14 Wall and floor attachment 14 15 For the installer 18 Important Notes to the Installer Read all instructions contained in these installation instructions before installing the range Remove all packing material from the oven and the drawer compartments before connecting the electrical supply to the range Observe all governing codes and ordinances Be sure to leave these instructions with the consumer Important Note to the Customer Keep these instructions with your owners guide for future reference Definitions This manual contains important safety symbols and instructions Please pay attention to these symbols and follow all instructions given IMPORTANT SAFETY INSTRUCTIONS WARNING If the instructions contained in this manual are not followed precisely a fire or explosion may result causing property damage personal injury or loss of life INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER IMPORTANT SAVE FOR THE LOCAL INSPECTORS USE
• Page 2 - English - : Important Safety Instructions TIP OVER HAZARD Check for proper installation and use of the antitip bracket Carefully tip the range forward by pulling it from the back to ensure that the antitip bracket engages the range leg and prevents tipover The range should not move more than 1 25cm Appliance Handling Safety Hidden surfaces may have sharp edges Use caution when reaching behind or under the appliance Wear gloves to avoid cutting fingers on sharp edges during installation The unit is heavy and requires at least two persons or proper equipment to move it Do not lift appliance by the oven door handle Remove the oven door for easier handling and installation Do not use the oven for storage WARNING This symbol will help alert you to situations that may cause serious bodily harm death or property damage CAUTION This symbol will help alert you to situations that may cause injury or property damage WARNING Tip Over Hazard A child or adult could tip the range over and be killed Install the antitip device on the floor or wall as per the installation instructions Engage the range with the anti tip device as per the installation instructions Ensure the antitip device is re engaged when the range is moved Do not operate the range without the antitip device in place and engaged See installation instructions for details Failure to follow these instructions can result in death or serious burns to children and adults To check if the antitip bracket is installed properly use both arms and grasp the back edge of the range Carefully attempt to tilt the range forward When properly installed the range should not tilt forward Refer to the antitip bracket installation instructions supplied with your range for proper installation
• Page 3 - English - : Important Safety Instructions EN Safety Codes and Standards This appliance complies with one or more of the following Standards UL 858 The Standard for the safety of Household Electric Ranges CANCSAC222 No 61 Household Cooking Ranges It is the responsibility of the owner and the installer to determine whether additional requirements andor standards apply to specific installations The appliance must be electrically grounded in accordance with local codes or in the absence of local codes with the National Electrical Code NFPA 70 latest edition or in Canada the Canadian Electric Code CSA C22102 Before installing the range in an area covered with linoleum or any other synthetic floor covering make sure the floor covering can withstand heat at least 90F above room temperature without shrinking warping or discoloring Do not install the range over carpeting unless you place an insulating pad or sheet of ¼quot 1016cm thick plywood between the range and carpeting Be sure your range is installed and grounded properly by a qualified installer or service technician Make sure the wall coverings around the range can withstand the heat generated by the range Do not store items of interest to children in the cabinets above the range Children could be seriously burned if they climb on the range to reach items Do not use the oven as a storage space This creates a potentially hazardous situation Do not store or use gasoline or other flammable vapors and liquids near this or any other appliance Explosions or fires could result Never use your range for warming or heating the room Prolonged use of the range without adequate ventilation can be dangerous WARNING Never leave children alone or unattended in the area where an appliance is in use As children grow teach them the proper safe use of all appliances Never leave the oven door open when the range is unattended CAUTION Stepping leaning or sitting on the doors or drawers of this range can result in serious injuries and can also cause damage to the range
• Page 4 - English - : Important Safety Instructions THIS COOKTOP IS NOT REMOVABLE Do not attempt to remove the cooktop Electric Safety Personal injury or death from electrical shock may occur if the appliance is not installed by a qualified installer or electrician Make sure your appliance is properly installed and grounded by a qualified electrician Installation electrical connections and grounding must comply with all applicable codes Before installing turn power OFF at the service panel Lock service panel to prevent power from being turned ON accidentally For appliances equipped with a cord and plug do not cut or remove the ground prong It must be plugged into a matching grounding type receptacle to avoid electrical shock If there is any doubt as to whether the wall receptacle is properly grounded the customer should have it checked by a qualified electrician Do not use an extension cord Do not use an adapter If required by the National Electrical Code or Canadian Electrical Code this appliance must be installed on a separate branch circuit The circuit breaker should have a contact separation of at least 3 mm on all poles INSTALLER show the owner the location of the circuit breaker or fuse Mark it for easy reference Refer to rating label for more information Proposition 65 Warning This product may contain a chemical known to the State of California which can cause cancer or reproductive harm Therefore the packaging of your product may bear the following label as required by California WARNING Do not repair replace or remove any part of the appliance unless specifically recommended in the manuals Improper installation service or maintenance can cause injury or property damage Refer to this manual for guidance All other servicing should be done by an authorized service provider WARNING Before you plug the electrical cord into an outlet make sure that all the appliance controls are in the OFF position State of California Proposition 65 WARNING Cancer or Reproductive Harm wwwP65Warningscagov
• Page 5 - English - : Important Safety Instructions EN Related Equipment Safety The appliance should only be used if installed by a qualified technician in accordance with these installation instructions and all applicable regulations and codes The manufacturer is not responsible for damages resulting from incorrect installation Remove all tape and packaging before using the appliance Dispose of the packaging after unpacking the appliance Never allow children to play with packaging material Never modify or alter the construction of the appliance For example do not remove leveling legs panels wire covers or anti tip bracketsscrews To eliminate the risk of burns or fire by reaching over hot surface units cabinet storage space located above the surface units should be avoided If cabinet storage is to be provided the risk can be reduced by installing a hood that projects horizontally a minimum of 5 inches 127 mm beyond the bottom of the cabinet Be sure cabinets above the cooktop are a maximum of 13quot 330 mm deep When installing a cooktop over a single oven be sure to follow both the oven and cooktop installation manuals Ventilation Recommendations Do not obstruct air vents or heat vent openings We strongly recommend the installation of a ventilation hood above this appliance The hood must be installed according to the instructions provided with the hood Do not obstruct the flow of combustion air at the oven vent nor around the base or beneath the lower front panel of the range Avoid touching the vent openings or nearby surfaces as they may become hot while the oven is in operation Air curtains or other overhead range hoods which operate by blowing air downwards onto a range shall not be used in conjunction with gas ranges other than when the hood and range have been designed tested and listed by an independent test laboratory for use in combination with each other CAUTION The appliance should not be installed with a ventilation system that blows air downward toward the cooktop This type of ventilation system may cause ignition and combustion problems with the gas cooking appliance and may result in personal injury or unintended operation
• Page 6 - English - : Important Safety Instructions High altitude installation This appliance can operate up to an altitude of 10000 ft 3048 m elevation above sea level If desired for altitudes above 2000 ft 610 m elevation above sea level adjustments may be made It is required that a Certified Professional make the high altitude adjustments during installation Improper installation is not covered by the warranty How to read the user manual This user manual uses the following reading conventions 1 Use instruction sequence Single use instructions SAVE THESE INSTRUCTIONS WARNING If the information in this manual is not followed exactly fire or shock may result causing property damage or personal injury Installation Information for the qualified technician installation operation and inspection Safety instructions Information Advice
• Page 7 - English - : Important Safety Instructions EN 1 Installation 11 Product dimensions Overall dimensions Location of electrical connection point E Electrical connection Measurement M varies according to the model the minimum is obtained without the rear spacers see quotIsland installationquot and the maximum is obtained for traditional installation slotin installation with the rear spacers Measurement N refers to the open door A quot 130 mm B quot 29 mm F min 3 quot Max 4 quot min 83 mm Max 113 mm H quot 809 mm L quot 9124 mm L quot 9124 mm M min 24 quot Max 25 min 626 mm Max 630 mm N quot 1088 mm O min 35 quot Max 36 quot min 892 mm Max 922 mm
• Page 8 - English - : Installation Cabinet clearances Clearance L can have the following values L 30 762 mm min minimum clearance between the top of the cooking surface and the bottom of an unprotected wood or metal cabinet L 24quot 610 mm minimum when the bottom of wood or metal cabinet is protected by not less than 14inch thick flameretardant millboard covered with not less than No 28 MSG sheet steel 0015inchthick stainless steel 0024inchthick aluminum or 0020 inchthick copper Clearances from non combustible materials are not part of the ANSI Z211 scope and are not certified by CSA Clearances of less than 30 should be approved by the local codes andor by the local authority having jurisdictiont min clearance from the sides of range to side wall or other combustible material min cabinet opening width upper cabinet to countertop max upper cabinet depth The side cabinet depth clearance B must match the front edge of the range side panel A 36quot 914 mm B 25 630 mm C 20quot 508 mm G min 36quot min 914 mm I 18quot 457 mm L see notes below M 13quot 330 mm P 13quot 330 mm The distance between the appliance and the rear wall below the worktop is zero The distance between the appliance and the side cabinets below the worktop is zero Any opening in the wall behind the appliance and in the floor under the appliance shall be sealed
• Page 9 - English - : Installation EN Location of the electric outlet Island installation If the appliance is installed as an island 1 Unscrew the screws shown 2 Remove the spacers A 3 Replace the screws that were previously removed Keep a minimum clearance of 5 quot 150 mm between the appliance and the other furnishings or decorative elements according to the diagram below The side cabinet depth clearance B must match the front edge of the range side panel D min 11 Min 300 mm M min 2 min 51 mm Max 9 Max 250 mm L min 11 min 300 mm Max 24 Max 614 mm
• Page 10 - English - : Installation 12 Unpacking moving and positioning the range When positioning the appliance during installation do not use the door handle to lift or move this appliance Remove the outer carton and packing material from the shipping base Remove anglemounting brackets from the range Due to its weight a dollyfork lift with soft rubber tread wheels should be used to move this unit The weight must be supported uniformly across the bottom The floor under the legs should be protected wood strips carpet paneling etc before pushing the unit into position The antitip device must be installed and the electrical connection should be made before the range is placed in its final position Legs should be installed near to where the appliance will be used as they are not secure for long transit Keep the unit raised so that the legs can be screwed into their couplings then lower the range gently to prevent the legs and mounting hardware from being subject to any undue strain Instead of tilting the unit it is recommended that a pallet or lift jack be used After making the electrical connection screw on the four feet supplied with the appliance CAUTION This unit is designed as a cooking appliance For safety reasons never use it for warming the room or as a space heater NOTE First insert the front feet and then the rear ones
• Page 11 - English - : Installation EN The appliance must sit level on the floor to ensure stability Screw or unscrew the bottom part of the foot until the appliance is stable and level on the floor The adjustment range of the screw is 11830 mm Assembling the backguard The backguard must always be positioned and secured correctly on the appliance 1 Position the backguard above the top taking care to align the holes 2 Secure the backguard to the top by tightening screws 3 Once you have fixed the backguard to the appliance you must insert the screws and spacers provided that are necessary for the slotin installation 13 Electrical connection NOTE this appliance must only use the specific leveling legs provided by the manufacturer The backguard provided is an integral part of the product it must be fastened to the appliance prior to installation WARNING Electrical shock hazard This appliance is equipped with a four prong grounding plug for your protection against electric shock and should be plugged directly into a properly grounded receptacle Do not cut or remove the grounding prong from this plug Failure to do any of the above could result in a fire personal injury or electrical shock
• Page 12 - English - : Installation This range is equipped with a factory connected power cord The cord must be connected to a grounded 120240 volt or 120208 volt outlet If no outlet is available have one installed by a qualified electrician See the rating plate for technical specifications The rating plate is visibly located on the right side of the oven door frame This ID plate must never be removed 14 Wall and floor attachment WARNING Electrical shock hazard Disconnect the electrical supply before servicing the appliance It is the personal responsibility of the consumer to have the appropriate outlet or junction box with the correct properly grounded wall receptacle installed by a qualified electrician It is the responsibility and obligation of the consumer to contact a qualified installer to ensure that the electrical installation is suitable and in conformance with all local codes and ordinances CAUTION Do not use multiple outlets extension cords or adapters WARNING Electrical shock hazard Use extreme caution when drilling holes in the wall or floor There may be concealed electrical wiring behind the wall or under the floor Identify the location of the electrical circuits that could be affected by the installation of the antitip device then turn off power to these circuits Failure to follow these instructions may result in electrical shock or other personal injury
• Page 13 - English - : Installation EN CAUTION Contact a qualified installer or contractor to determine the proper method for drilling holes through the wall or floor material such as ceramic tile hardwood etc Failure to follow these instructions may result in damage to wall or floor coverings WARNING Visually check from the inside of the drawer that the wallfloormounted bracket is inserted into the appropriate lateral hook left side WARNING Tip Over Hazard A child or adult could tip the range over and be killed Install the antitip device on the floor or wall as per the installation instructions Engage the range with the anti tip device as per the installation instructions Ensure the antitip device is re engaged when the range is moved Do not operate the range without the antitip device in place and engaged See installation instructions for details Failure to follow these instructions can result in death or serious burns to children and adults
• Page 14 - English - : Installation Installing the antitip bracket 1 Ensure that the electrical connection is in the correct position 2 Assemble the bracket 3 Align the base of the hook of the bracket with the base on the slot of the rear wall fastening bracket Align the base of the fastening bracket with the floor and tighten the screws to fix the measurements 4 For wall mounting go to steps 5 6 9 and 10 For floor mounting to steps 7 8 and 10 5 Use the specified distance from the side of the appliance to the bracket holes 6 Move the bracket to the wall and fix with the two washers and screws A qualified technician must verify the suitability of the materials in accordance with the type and condition of the wall NOTE The wall attachment is recommended if the appliance is placed against a wall Floor attachment is recommended in case of island installation
• Page 15 - English - : Installation EN 7 Use the following distances for the distance from the side of the appliance to the bracket holes 8 After having positioned and leveled the appliance move the bracket close to the rear of the appliance and anchor it to the floor using the two washers and screws A qualified technician must verify the suitability of the materials in accordance with the type and condition of the floor 9 Push the cooker towards the wall and at the same time insert the bracket in the plate that is fastened to the rear of the appliance 10 Check for proper installation and use of the antitip bracket Carefully tip the range forward by pulling it from the back to ensure that the antitip bracket engages the range leg and prevents tipover The range should not move more than 1 25cm WARNING The rear vent trim has 5 mm standoffs to keep the appliance slightly away from the back wall Do not remove or tamper with standoffs due to potential temperature issues
• Page 16 - English - : Installation Door removal It is not necessary to remove the door in order to install the range but is an added convenience Refer to the Use and Care Guide for the oven door removal instructions 15 For the installer The plug must remain accessible after the installation is complete Do not kink or trap the mains connection cable The appliance must be fitted according to the installation diagrams When satisfied with the appliance please instruct the user on the correct method of operation In case the appliance fails to operate correctly after all checks have been carried out refer to the Authorized Assistance Center in your area LEAVE THESE INSTRUCTIONS WITH APPLIANCE AFTER INSTALLATION IS COMPLETE