NINJA WOODFIRE™ PRO XL OUTDOOR
GRILL & SMOKER WITH BUILT-IN THERMOMETER
OG900 Series | Owner’s Guide
IMPORTANT SAFETY INSTRUCTIONS
OUTDOOR HOUSEHOLD USE ONLY. READ ALL INSTRUCTIONS BEFORE USE
WARNING
Failure to follow these instructions could result in electric shock, fire or burn hazard which could cause property
damage, personal injury, or death. When using electrical appliances, basic safety precautions should always be
followed, including the following:
1 To eliminate a choking hazard for young children, discard all packaging materials immediately upon unpacking.
2 This appliance is for outdoor household use only.
3 DO NOT use this appliance for anything other than its intended use. Misuse may cause injury.
4 DO NOT operate this appliance unattended.
5 DO NOT use in moving vehicles or boats.
6 This appliance can be used by persons with reduced physical, sensory, or mental capabilities or lack of experience and knowledge if they
have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
7 To avoid property damage from flame or heat maintain a minimum distance of 3 feet from rear, sides and top to walls, rails, or other
combustible constructions.
8 To avoid property damage and burn injury from flame or heat, ALWAYS maintain a minimum safe distance of at least 1 foot (30 cm)
from the pellet box during smoking. Small flames can come out from the pellet box if the grill lid is lifted in windy conditions.
9 To avoid burn injury, DO NOT lean over grill while cooking.
10 DO NOT place on or near a hot gas or electric burner, or in a heated oven.
11 ALWAYS use pellet scoop when adding pellets to smoker box. DO NOT add pellets by hand.
12 To avoid burn injury and property damage, make sure the lid of the smoke box is fully closed to prevent flames from escaping out of
the smoke box.
13 Pellets may continue to burn after cook time is complete. DO NOT touch or remove the smoke box until the grill has stopped smoking,
pellets have completely burnt out, and the smoke box has cooled.
14 To avoid personal injury and burns allow to cool before cleaning, disassembly, putting in or taking off parts and storage.
15 DO NOT allow pellets to overflow the pellet box. Doing so will introduce oxygen leading to combustion, flame, and damage to the
unit which may result in burn injury.
16 DO NOT touch hot surfaces. Appliance surfaces are hot during and after operation. To prevent burns or personal injury, ALWAYS use
protective hot pads or insulated oven mitts and use available handles and knobs.
17 DO NOT touch accessories during or immediately after cooking. The basket will become extremely hot during the cooking process.
Avoid physical contact while removing the accessory from the appliance. To prevent burns or personal injury ALWAYS use care when
interfacing with product. Recommend use of long handed utensil and protective hot pads or insulated oven mitts.
18 Ensure the surface is level, stable, clean and dry. DO NOT place the appliance near the edge of the surface the grill is placed on during
operation.
19 Keep the appliance and its cord out of reach of children. DO NOT allow the appliance to be used near, cleaned, or maintained by
children. Close supervision is necessary when used near children.
20 CONNECT ONLY TO GFCI GROUNDED ELECRICAL OUTLET IF USING AN EXTENSION CORD
Read and review instructions to understand operation and use of product.
Indicates the presence of a hazard that can cause personal injury, death or substantial property damage if
the warning included with this symbol is ignored.
Avoid contact with hot surface. Always use hand protection to avoid burns.
2 3
ninjakitchen.com
ninjakitchen.com
PARTS & ACCESSORIES
A Grill Grate
B Crisper Basket
C Smoke Box
D Grease Tray
E Grease Tray Liner
F Pellet Scoop
G Main Unit
(power cord not shown)
H Hood
I Control Panel
J Onboard Thermometer storage
K Built-in Thermometer(s)
(not all models include
two thermometers)
A
21 A short power-supply cord is provided to reduce the risk of children less than 8 years grabbing the cord or becoming entangled
and to reduce the risk of people tripping over a longer cord. When using an extension cord it must be specific for use outdoors
and must have a “W” marking and tag stating: SUITABLE FOR USE WITH OUTDOOR APPLIANCES.
22 ALWAYS ensure the grill is completely cool before releasing and removing the cooking plates or moving the to avoid burns or
personal injury.
23 DO NOT use the appliance without the grill plate installed.
24 To protect against electrical shock, keep the cord connection dry and DO NOT immerse cord, plugs, or main unit housing in water
or other liquid.
25 Regularly inspect the appliance and power cord. DO NOT use the appliance if there is damage to the power cord or plug. If the
appliance malfunctions or has been damaged in any way, immediately stop use and call Customer Service.
26 NEVER use outlet below countertop surface.
27 ALWAYS ensure the appliance is properly assembled before use. DO NOT use without side handles attached.
28 NEVER connect this appliance to an external timer switch or separate remote-control system.
29 DO NOT place appliance and let cord hang over edges of tables, counters or touch hot surfaces.
30 Only use recommended accessories included with this appliance or authorized by SharkNinja. The use of accessories or attachments
not recommended by SharkNinja may cause a risk of fire or injury.
31 Before placing any accessory into the cooker, ensure they are clean and dry.
32 DO NOT move the appliance when in use.
33 DO NOT cover the air intake vent or air outlet vent while unit is operating. Doing so will prevent even cooking and may damage
the unit or cause it to overheat.
34 DO NOT place anything on top of the product when the hood is closed during use and stored.
35 Ensure the grill plate is correctly inserted and securely locked into position.
36 DO NOT use this appliance for deep-frying.
37 Some foods may cause oils or grease to splash. Use care when opening the grill to avoid burns.
38 Should a grease fire occur, or the unit emits black smoke, unplug immediately. Wait for smoking to stop before removing any
cooking accessories.
39 Socket voltages can vary, affecting the performance of your product. To prevent possible illness, ALWAYS use an external food
thermometer to check that your food is cooked to the recommended temperatures.
40 DO NOT use heating or any other non-food-grade pellets in the grill, due to potential hazardous contaminants and additives that
may be present.
41 DO NOT use heating or any other non-food-grade pellets in the grill, due to potential hazardous contaminants and additives that
may be present.
42 NEVER use heating fuel pellets, hardwood, charcoal, liquid fuels, or any other combustible material in the Smoker.
43 Keep hands and face away from Smoker Box when unit is in use and hot.
44 ALWAYS keep a fire extinguisher accessible while operating the smoker.
45 ALWAYS store wood pellets in a dry location, away from heat-producing appliances and other fuel containers.
46 Keep your grill clean. DO NOT allow excess grease or ash to collect inside the grease tray, or on the smoke box and cartridge.
Doing so significantly increases the chances of a grease fire and additional smoke which can taint the flavor of your food.
47 Please refer to the Cleaning & Maintenance section for regular maintenance of the appliance.
48 To disconnect, press the power button to turn the unit off, then unplug from socket when not in use and before cleaning.
49 DO NOT clean with metal scouring pads. Pieces can break off the pad and touch electrical parts, creating a risk of electric shock.
50 When storing and not in use, keep out of reach of children.
51 Keep grill covered when not in use.
IMPORTANT SAFETY INSTRUCTIONS
OUTDOOR HOUSEHOLD USE ONLY. READ ALL INSTRUCTIONS BEFORE USE
SAVE THESE INSTRUCTIONS
WARNING
Failure to follow these instructions could result in electric shock, fire or burn hazard which could cause property
damage, personal injury, or death. When using electrical appliances, basic safety precautions should always be
followed, including the following:
J K
B
D
E
C
G
H
I
F
1 Remove all packaging material, and tape from the unit.
2 Remove all accessories from the package and read this manual carefully. Please pay particular
attention to operational instructions, warnings, and important safeguards to avoid any injury or
property damage.
3 Wash the grill grate and crisper basket in warm, soapy water, then rinse and dry thoroughly. The grill grate,
crisper basket and base unit are NOT dishwasher safe. NEVER clean the main unit in the dishwasher.
4 DO NOT use abrasive brushes or sponges on the cooking surfaces, as it will cause damage to the coating.
BEFORE FIRST USE
We recommend placing all accessories inside the grill and running it on GRILL,
temp set to HI for 20 minutes without adding food. This removes any residues.
This is completely safe and not detrimental to the performance of the grill.
EXTENSION CORD
1
Connect to properly 3-prong grounded GFCI outlets only.
2
Use only outdoor extension cords marked as "SJOW" and "suitable for use with outdoor appliances."
For cords up to 25 feet, use 14-gauge. For 25 to 50-foot cords, use 12-gauge. Cords longer than 50 feet
are not recommended. Using the incorrect cord could lead to the cord overheating, melting, and/or a
drop in voltage. A drop in voltage can increase preheat times and impact cooking performance and/or
cook times.
NOTE: Included accessories may vary by model.
2 Plug the thermometer into the top jack
labeled “1" on the left side of the control
panel. Push firmly on the plug until it cannot
go into the jack any further. Slide the storage
compartment back.
3 After the thermometer is plugged into the
jack, select the desired cook function and
cook temperature.
4 Press the Thermometer button, then use the
dial to select your desired protein type or
Manual. Press dial to confirm selection.
5 Use the dial to select your desired doneness or
manual internal temperature, then press dial to
confirm selection.
4 5
ninjakitchen.com
ninjakitchen.com
GETTING TO KNOW THE NINJA WOODFIRE™ PRO XL
OUTDOOR GRILL & SMOKER WITH BUILT-IN THERMOMETER
FUNCTION BUTTONS
GRILL: Closed-hood cooking for top and bottom
heat. Best when grilling large or thick cuts of
meat or frozen food or for an all-around sear.
Open the hood while grilling delicate foods or
lean proteins to develop char-grilled textures
without overcooking.
SMOKER: Create deep, smoky flavors while
cooking low and slow to tenderize large cuts
of meat.
AIR CRISP: Achieve crispiness and crunch with
little to no oil and higher fan speeds.
BAKE: Bake cakes, treats, desserts, and more
with lower fan speeds.
ROAST: Tenderize meats, roast vegetables, and
more.
BROIL: Add a crispy finishing touch to meals or
melt cheese on sandwiches.
DEHYDRATE: Dehydrate meats, fruits, and
vegetables for healthy snacks.
OPERATING BUTTONS
DIAL: Use the dial to adjust your temperature,
cook time, or thermometer settings.
WOODFIRE FLAVOR: Press after selecting
your cooking function to add authentic smoky
flavors. Intended for use with the Grill, Air Crisp,
Bake, Roast, and Dehydrate functions. When
pressed, flame icon will illuminate on the display
screen.
TEMP: Press TEMP to change the grill
temperature, use the dial to increase or
decrease temperature.
TIME: Press TIME to change the cook time, use
the dial to increase or decrease time.
START/STOP: Press to start or stop the current
cook function, or press and hold for 4 seconds to
skip preheat.
PREHEAT FOR BETTER RESULTS
For best grilling results, let the grill fully preheat
before adding food. Adding food before
preheating is complete may lead to overcooking,
smoke, and longer preheat time.
After you set function, time, and temperature
then press START/STOP, the unit will
automatically begin preheating (except if
using the Smoker/Broil function or the
Dehydrate function without enabling Ninja
Woodfire Flavor).
NOTE: Not all functions included with every model.
NOTE: When the unit is powered on, the
display will be illuminated.
NOTE: Ninja Woodfire Flavor is automatically
enabled when using the Smoker function.
MYLAR + DIAL
OG951 OG901 UI SPEC
Before First Use
Make sure the thermometer jack is free of any
residue and the cord is free of knots before
plugging it into the jack.
1 Slide out the thermometer storage
compartment from under the control panel,
then unwind the cord from the compartment
to remove the thermometer.
NOTE: There is no need to set a cook time, as
the grill will automatically turn o the heating
element and alert you when your food has
finished cooking.
NOTE: Cooking dierent proteins or the
same ones to dierent doneness?
Use the second thermometer. Plug into the
jack labeled "2". Press the Thermometer
button again. The thermometer 2 icon will
flash. Repeat steps 3–5 to program the
second thermometer.
IMPORTANT: DO NOT place hands near
built-in thermometer(s) cord(s) when in use
to prevent burning or scalding.
USING THE BUILT-IN THERMOMETER(S)
SMOKE BOX
Comes fully installed in the unit. Located on the right side of the hood. Always ensure the removeable
smoke box is inserted into place before adding pellets. Review all warnings before proceeding.
Installing the smoke box:
To install, pull the smoke box open with one hand and insert the
removable smoke box so it sits into place.
Removing the smoke box and cleaning:
To avoid burns, allow pellets to burn completely and the smoke box to cool completely,
then remove smoke box and safely discard all contents.
Adding Ninja Woodfire™ Pellets:
Fill the pellet scoop to the top and level o to avoid spilling. While holding the smoke box
open, use the pellet scoop to pour pellets into the smoke box until filled to the top. Then,
close the smoke box.
Use only Ninja Woodfire Pellets for best results, performance, and flavor.
6
ninjakitchen.com
7
ninjakitchen.com
8 The progress bar at the top of the display will
track doneness. Flashing doneness indicates
progression to that doneness.
9 The grill will automatically stop when desired
doneness is almost reached, as it accounts
for carry-over cooking, and “GET FOOD” will
display on the screen.
10 Transfer the protein to a plate while “REST”
displays on the screen. Thermometer does
not need to still be inserted. The protein
will continue to carry-over cook to your set
doneness, which will take about 3–5 minutes.
This is an important step, as not resting could
lead to results looking less cooked. Carry-over
cook times can vary based on size of protein,
cut of protein, and type of protein.
USING THE BUILT-IN THERMOMETER(S) – CONT'D
NOTE: The thermometer will be HOT. Use
either oven mitts or tongs to take the
thermometer out of the protein.
NOTE: To check the internal temperature
of other pieces of protein, press and hold
the Thermometer button and insert the
thermometer into each piece of meat.
5 Place the accessory required for your selected
cook function in the grill and close the hood.
Press START/STOP to begin preheating.
6 While the grill is preheating, insert the
thermometer horizontally into the center
of the thickest part of the piece of protein.
Refer to the chart on the next page for
further thermometer placement instructions.
7 When the grill has preheated and “ADD
FOOD” appears on the screen, open the
hood, place food with inserted thermometer
in the unit, and close the hood over the
thermometer cord.
Correct thermometer placement.
Thermometer grip is fully inside unit.
NOTE: When using Grill and Roast, the unit
will beep and display FLIP. Flipping is optional,
but recommended.
FOOD TYPE: PLACEMENT CORRECT INCORRECT
Steaks
Pork chops
Lamb chops
Chicken breasts
Burgers
Tenderloins
Fish fillets
• Insert thermometer
horizontally into the center
of the thickest part of the
meat.
• Make sure the thermometer
is close to (but not touching)
the bone and away from any
fat or gristle.
• Make sure the tip of the
thermometer is inserted
straight into the center of
the meat, not angled toward
the bottom or top of it.
NOTE: The thickest part
of the fillet may not be
the center. It is important
that the end of the
thermometer hits this area
so that desired results are
achieved.
Whole chicken
• Insert thermometer
horizontally into the thickest
part of the breast, parallel to
(but not touching) the bone.
• Make sure the tip reaches
the center of the thickest
part of the breast and
doesn’t go all the way
through the breast into the
cavity.
HOW TO CORRECTLY INSERT THE THERMOMETER
NOTE: DO NOT use the thermometer with frozen protein or for cuts of meat thinner than 1 inch.
NOTE: Preset doneness temperatures for BEEF/
LAMB are lower than normal recommendations,
as unit will carry-over cook 10–15°F.
NOTE: Reference USDA guidelines for
food-safe temperature recommendations.
FOOD TYPE: SET DONENESS TO:
Fish Medium (130°F)
Medium Well (140°F)
Well Done (150°F)
Chicken/Turkey Well Done (165°F)
Pork Medium (130°F)
Medium Well (150°F)
Well Done (160°F)
Beef/Lamb Rare (115°F)
Medium Rare (125°F)
Medium (130°F)
Medium Well (145°F)
Well Done (150°F)
If selecting MANUAL, use the below
recommended internal cook temperatures.
8 9
ninjakitchen.com
ninjakitchen.com
COOKING FUNCTIONS
IMPORTANT: Review all warnings at the beginning of this Owner’s Guide before proceeding.
Grill
1 Place grill on a flat, level surface.
2 Open the hood and install the grill grate
by positioning it flat on top of the heating
element so it sits in place.
3 Install the grease tray by sliding it into place at
the back of the grill.
4 If you plan to add Ninja Woodfire Flavor,
pull the smoke box open and use the
pellet scoop to fill the smoke box with
Ninja Woodfire Pellets to the top. DO NOT
overflow the smoke box.
5 Make sure the grill is plugged in and press
the MODE button or use the dial to select the
GRILL function.
6
If adding Ninja Woodfire Flavor, press the
WOODFIRE FLAVOR button.
7 The default temperature setting will display.
To adjust temperature, if desired, press TEMP
and use the dial to increase or decrease
temperature. Press dial to confirm, otherwise
temperature will lock in after 5 seconds.
8 To adjust cook time, press TIME and use the
dial to increase or decrease cook time. Press
dial to confirm, otherwise cook time will lock
inafter 5 seconds.
9 Press START/STOP to begin preheating. If
using Ninja Woodfire Flavor, the pellets will go
through an ignition cycle (IGN), then the grill
will begin preheating (PRE).
10 When preheating is complete, the grill will
beep and ADD FOOD will appear on the display.
11
Open the hood and place ingredients on the
grill grate. Once the hood is closed, cooking will
begin and the timer will begin counting down.
12 When cook time reaches zero, the grill will
beep and DONE will appear on the display.
13 Remove food from the grill grate.
NOTE: If you are using the thermometer, refer to
the Using the Built-In Thermometer(s) section.
Smoker
1 Place grill on a flat, level surface.
2 Open the hood and install the grill grate
by positioning it flat on top of the heating
element so it sits in place.
3 Install the grease tray by sliding it into place
at the back of the grill.
4 Pull the smoke box open and use the pellet
scoop to fill the smoke box with Ninja
Woodfire Pellets to the top. DO NOT overflow
smoke box.
5 Open the hood and place ingredients on the
grill grate. Close the hood.
6 Make sure the grill is plugged in and press
the MODE button or use the dial to select the
SMOKER function.
7 The default temperature setting will display.
To adjust temperature, if desired, press TEMP
and use the dial to increase or decrease
temperature. Press dial to confirm, otherwise
temperature will lock in after 5 seconds.
8 To adjust cook time, press TIME and use the
dial to increase or decrease cook time. Press
dial to confirm, otherwise cook time will lock
after 5 seconds.
9 Press START/STOP to begin cooking. There
is no preheat time for the Smoker function.
The pellets will go through an ignition cycle
(IGN) for 5–7 minutes, then the grill will begin
cooking and the timer will begin to count
down.
10 When cook time reaches zero, the grill will
beep and DONE will appear on the display.
11 Remove food from the grill grate.
NOTE: If you are using the thermometer, refer to
the Using the Built-In Thermometer(s) section.
NOTE: While preheating is strongly
recommended for best results, you can skip
it by pressing and holding the START/STOP
button for 4 seconds. ADD FOOD will flash
across the screen. Open the hood and place
ingredients on the grill grate. Once the hood
is closed, cooking will begin and the timer
will start counting down. Skip to step 12.
NOTE: Ninja Woodfire Flavor is automatically
enabled when using the Smoker function.
NOTE: Want to cook with the hood open?
After you've added food, keep the lid open,
the timer will begin to count down after 30
seconds, and you will be cooking with bottom
heat only.
IMPORTANT: Review all warnings at the beginning of this Owner’s Guide before proceeding.
Air Crisp
1 Place grill on a flat, level surface.
2 Open the hood and install the grill grate
by positioning it flat on top of the heating
element so it sits in place.
3 Place the crisper basket on the grill grate,
positioning the basket feet in the designated
indentations.
4 Install the grease tray by sliding it into place
at the back of the grill.
5
If you plan to add Ninja Woodfire™ Flavor,
pull the smoke box open and use the
pellet scoop to fill the smoke box with
Ninja Woodfire Pellets to the top.
DO NOT overflow the smoke box.
6 Make sure the grill is plugged in and press
the MODE button or use the dial to select
the AIR CRISP function.
7
If adding Ninja Woodfire Flavor, press the
WOODFIRE FLAVOR button.
8 The default temperature setting will display.
To adjust temperature, if desired, press TEMP
and use the dial to increase or decrease
temperature. Press dial to confirm, otherwise
temperature will lock in after 5 seconds.
9 To adjust cook time, press TIME and use the
dial to increase or decrease cook time. Press
dial to confirm, otherwise cook time will lock
in after 5 seconds.
10 Press START/STOP to begin preheating. If
using Ninja Woodfire Flavor, the pellets will
go through an ignition cycle (IGN), then the
grill will begin preheating (PRE).
11 When preheating is complete, the grill will
beep and ADD FOOD will appear on the
display.
12 Open the hood and place ingredients on the
grill grate. Once the hood is closed, cooking
will begin and the timer will begin counting
down.
13 When cook time reaches zero, the grill will
beep and DONE will appear on the display.
14 Remove food from the crisper basket.
NOTE: If you are using the thermometer, refer
to the Using the Built-in Thermometer section.
Bake
1 Place grill on a flat, level surface.
2 Open the hood and install the grill grate
by positioning it flat on top of the heating
element so it sits in place.
3 Install the grease tray by sliding it into place at
the back of the grill.
4
If you plan to add Ninja Woodfire Flavor,
pull the smoke box open and use the
pellet scoop to fill the smoke box with
Ninja Woodfire Pellets to the top. DO NOT
overflow the smoke box.
5 Make sure the grill is plugged in and press
the MODE button or use the dial to select the
BAKE function.
6
If adding Ninja Woodfire Flavor, press the
WOODFIRE FLAVOR button.
7 The default temperature setting will display.
To adjust temperature, if desired, press TEMP
and use the dial to increase or decrease
temperature. Press dial to confirm, otherwise
temperature will lock after 5 seconds.
8 To adjust cook time, press TIME and use the
dial to increase or decrease cook time. Press
dial to confirm, otherwise cook time will lock
in after 5 seconds.
9 Press START/STOP to begin preheating. If
using Ninja Woodfire Flavor, the pellets will go
through an ignition cycle (IGN), then the grill
will begin preheating (PRE).
10 When preheating is complete, the grill will beep
and ADD FOOD will appear on the display.
11 Open the hood and place ingredients on the
grate or place bake pan on the grate. Once
the hood is closed, cooking will begin and the
timer will start counting down.
12 When cook time reaches zero, the grill will
beep and DONE will appear on the display.
13 Remove food from the grill grate.
NOTE: When using the Bake function, make
sure to use the proper accessory. For wet or
battered ingredients, use a baking dish. For
loose items, such as cinnamon rolls, hand pies,
or biscuits, use the crisper basket.
NOTE: If you are using the thermometer, refer to
the Using the Built-In Thermometer(s) section.
NOTE: While preheating is strongly
recommended for best results, you can skip
it by pressing and holding the START/STOP
button for 4 seconds. ADD FOOD will flash
across the screen. Open the hood and place
ingredients in the crisper basket. Once the
hood is closed, cooking will begin and the
timer will start counting down. Skip to step 13.
NOTE: While preheating is strongly
recommended for best results, you can skip
it by pressing and holding the START/STOP
button for 4 seconds. ADD FOOD will flash
across the screen. Open the hood and place
ingredients in the crisper basket. Once the
hood is closed, cooking will begin and the
timer will start counting down. Skip to step 12.
10 11
ninjakitchen.com
ninjakitchen.com
Broil
1 Place grill on a flat, level surface.
2 Open the hood and install grill grate by
positioning it flat on top of the heating
element so it sits in place.
3 Install the grease tray by sliding it into place
at the back of the grill.
4 Open the hood and place ingredients on
the grill grate. Close the hood. There is no
preheat.
5 Make sure the grill is plugged in and press
the MODE button or use the dial to select the
BROIL function.
6 The default temperature setting will display.
To adjust temperature, if desired, press TEMP
and use the dial to increase or decrease
temperature. Press dial to confirm, otherwise
temperature will lock in after 5 seconds.
7 To adjust cook time, press TIME and use the
dial to increase or decrease cook time. Press
dial to confirm, otherwise cook time will lock
in after 5 seconds.
8 Press START/STOP to begin cooking.
9 When cook time reaches zero, the grill will
beep and DONE will appear on the display.
10 Remove food from the grill grate.
IMPORTANT: Review all warnings at the beginning of this Owner’s Guide before proceeding.
Roast
1 Place grill on a flat, level surface.
2 Open the hood and install grill grate by
positioning it flat on top of the heating
element so it sits in place.
3 Install the grease tray by sliding it into place
at the back of the grill.
4 If you plan to add Ninja Woodfire™ Flavor,
pull the smoke box open and use the
pellet scoop to fill the smoke box with
Ninja Woodfire Pellets to the top. DO NOT
overflow the smoke box.
5 Make sure the grill is plugged in and press
the MODE button or use the dial to select the
ROAST function.
6 If adding Ninja Woodfire Flavor, press the
WOODFIRE FLAVOR button.
7 The default temperature setting will display.
To adjust temperature, if desired, press TEMP
and use the dial to increase or decrease
temperature. Press dial to confirm, otherwise
temperature will lock after 5 seconds.
8 To adjust cook time, press TIME and use the
dial to increase or decrease cook time. Press
dial to confirm, otherwise cook time will lock
in after 5 seconds.
9 Press START/STOP to begin preheating. If
using Ninja Woodfire Flavor, the pellets will
go through an ignition cycle (IGN), then the
grill will begin preheating (PRE).
10 When preheating is complete, the grill will
beep and ADD FOOD will appear on the
display.
11 Open the hood and place ingredients on the
grill grate. Once the hood is closed, cooking
will begin and the timer will begin counting
down.
12 When cook time reaches zero, the grill will
beep and DONE will appear on the display.
13 Remove food from grill grate.
NOTE: If you are using the thermometer, refer
to the Using the built-in Thermometer section.
NOTE: If you are using the thermometer, refer
to the Using the built-in Thermometer section.
NOTE: Ninja Woodfire Flavor cannot be used
with the Broil function.
Dehydrate
1 Place grill on a flat, level surface.
2 Open the hood and install grill grate by
positioning it flat on top of the heating
element so it sits in place.
3 Install the grease tray by sliding it into place
at the back of the grill.
4 Open the hood and place ingredients on the
grill grate. Close the hood.
5 If you plan to add Ninja Woodfire™ Flavor,
pull the smoke box open and use the
pellet scoop to fill the smoke box with
Ninja Woodfire Pellets to the top. DO NOT
overflow the smoke box.
6 Make sure the unit is plugged in and rotate the
dial clockwise from the OFF position to select
the DEHYDRATE function.
7 If adding Ninja Woodfire Flavor, press the
WOODFIRE FLAVOR button.
8 The default temperature setting will display.
To adjust temperature, if desired, press TEMP
and dial to increase or decrease temperature.
Press dial to confirm, otherwise temperature
will lock in after 5 seconds.
9 To adjust cook time, press TIME and use the
dial to increase or decrease cook time. Press
dial to confirm, otherwise cook time will lock
after 5 seconds.
10 Press START/STOP to begin cooking. There
is no preheat time for the Dehydrate function.
If you are using Ninja Woodfire Flavor, the
pellets will go through an ignition cycle (IGN)
for 5–7 minutes, then the grill will begin
cooking and the timer will begin to count
down.
11 When cook time reaches zero, the grill will
beep and DONE will appear on the display.
12 Remove food from the grill grate.
IMPORTANT: Review all warnings at the beginning of this Owner’s Guide before proceeding.
COOKING FUNCTIONS – CONT'D
NOTE: While preheating is strongly
recommended for best results, you can skip
it by pressing and holding the START/STOP
button for 4 seconds. ADD FOOD will flash
across the screen. Open the hood and place
ingredients in the crisper basket. Once the
hood is closed, cooking will begin and the
timer will start counting down. Skip to step 12.
12 13
ninjakitchen.com
ninjakitchen.com
TROUBLESHOOTING GUIDE
WARNING: To reduce the risk of shock and unintended operation, turn power o and unplug
unit before troubleshooting.
• “Add Food” appears on the control panel display.
The grill has completed preheating and it is now time to add your ingredients.
• “Shut Lid” appears on the control panel display.
The hood is open and needs to be closed for the selected function to start.
• “Add Grill” appears on the control panel.
The grill plate needs to be installed. Once installed, close the hood and press the START/STOP button
to begin.
• What does OTA mean?
An update is being sent to the grill. Do not unplug during this process. Wait for OTA to finish before use.
• “E” appears on the control panel display.
The grill is not functioning properly. Contact Customer Service at 1- 855-427-5125. So we may better assist you,
please register your product online at registeryourninja.com and have the product on hand when you call.
• "CLD" appears on the control panel display.
Cold Smoking is to be used to provide smoke flavor to foods and is not intended for cooking.
When used on meat, poultry, or fish, this process should always be used in conjunction with a
separate step to bring food up to food-safe internal temperatures. Reference USDA guidelines for
food-safe temperature recommendations.
• Should I add my ingredients before or after preheating?
For best results, let the grill preheat before adding ingredients.
• Why did a circuit breaker trip while using the unit?
The unit uses 1760 watts of power, so it must be plugged into an outlet on a 15-amp circuit breaker.
Using an outlet on a 10-amp breaker will cause the breaker to trip. It is also important that the unit
be the only appliance plugged into an outlet when in use. To avoid tripping a breaker, make sure the
unit is the only appliance plugged into an outlet on a 15-amp breaker.
• Do I need to completely fill the smoke box with pellets?
Yes, always fill the smoke box to the top. We've perfected the amount of pellets needed for each
smoke session. Regardless of the function or food load, the grill will burn through them appropriately.
• “Plug In” appears on the control panel display.
The thermometer is not plugged into the jack on the right side of the control panel. Plug the
thermometer in before proceeding. Press the thermometer in until you hear a click.
• Why does the unit have a 1–9 scale for the Beef Preset?
Perception of what a specific internal doneness looks like diers from person to person, even
restaurant to restaurant. The 1–9 scale provides a wide range of options for each doneness level so
you can customize doneness to your liking.
• “PRBE ERR” appears on the control panel display.
This means the grill timed out before food reached the set internal temperature. As a protection for
the unit, it can run for only certain lengths of time at specific temperatures.
• Why is there a bend/dent on the inside of the lid?
This is not a bend in the metal; it is designed to properly drain grease from the inside of the unit
while cooking.
• Why is my food overcooked or undercooked even though I used the thermometer?
It is important to insert the thermometer lengthwise into the thickest part of the ingredient to get
the most accurate reading. Make sure to allow food to rest for 3–5 minutes to complete cooking.
For more information, refer to the Using the built-in Thermometer section.
• When do I press the WOODFIRE FLAVOR Button?
Press the WOODFIRE FLAVOR button before pressing START/STOP in order to add authentic
smoky flavors for the Grill, Air Crisp, Roast, Bake, or Dehydrate function. Ninja Woodfire™ Flavor is
automatically enabled when using the Smoker function.
• Where should I keep my pellets stored?
Always store pellets in a dry area. Any moisture in the pellets can compromise ignition and quality of
smoke flavor.
GETTING TO KNOW THE NINJA WOODFIRE™ PRO XL
OUTDOOR GRILL & SMOKER WITH BUILT-IN THERMOMETER
The grill should be cleaned thoroughly after each
use. ALWAYS let the appliance and accessories
cool before cleaning.
• Unplug the grill from power source before
cleaning. Keep the hood open after removing
your food to allow the unit to cool quicker.
• Remove smoke box and safely discard all
contents after every use.
• The pellet scoop is dishwasher safe. The grill
grate, crisper basket, grease tray, and smoke
box are not dishwasher safe.DO NOT place the
thermometer in the dishwasher.
• The Built-In Thermometer and holder are hand-
wash only. DO NOT immerse any part of the
thermometer in water or any other liquid. We
recommend cleaning with a damp cloth only.
• Carefully remove cooled grease tray from back
of unit and safely discard grease contents after
each use. Hand-wash grease tray in warm,
soapy water.
• It is not required to clean the smoke box after
every use. We recommend using a wire brush
to remove extra creosote after every 10 uses.
• The inner hood should be wiped down with
a damp towel or cloth after each use to
deodorize the unit and remove any grease.
• If food residue or grease is stuck on the grill
grate or any other removable part, soak in
warm, soapy water before cleaning.
• Remove non-stick grill grate and non-stick
crisper basket (if used) after each use and
hand-wash with warm, soapy water.
• Gently wipe down the inside of the hood with
a damp cloth.
• When stacking the coated accessories to
store, place a cloth or paper towel between
each piece to protect the coated surfaces.
NOTE: NEVER use abrasive tools or cleaners.
NEVER immerse the main unit in water or any
other liquid. DO NOT place in dishwasher.
NOTE: DO NOT use liquid cleaning solution
on the smoke box.
To order additional parts and accessories, visit ninjaaccessories.com or contact Customer Service at
1-855-427-5125. We ask that you register your product online at registeryourninja.com and have the
product on hand when you call, so we may better assist you.
REPLACEMENT PARTS
14 15
ninjakitchen.com
ninjakitchen.com
TROUBLESHOOTING GUIDE – CONT'D TROUBLESHOOTING GUIDE – CONT'D
• Should I use any oils or nonstick sprays when smoking?
No, we do not recommend using any oils or nonstick sprays when smoking because smoke will not
adhere to the food as well.
• How do I dispose of burnt pellets after a cook cycle?
Pellets may continue to burn after cook time is complete. Do not touch or remove the smoke box
until the grill has stopped smoking, pellets have completely burnt out, and the smoke box has
cooled. At that point, remove the smoke box and safely discard cooled ash contents.
• Why is preheat taking so long?
Preheat times vary by function and unit temperature.
GRILL: LOW: 9–12 minutes MED: 10–13 minutes HIGH: 13–15 minutes
AIR CRISP, BAKE, ROAST: 2–3 minutes
SMOKER, DEHYDRATE, BROIL: No preheat.
If adding Ninja Woodfire™ Flavor, ignition time will add an additional 3–6 minutes.
Using the unit in inclement weather with heavy rain could cause longer preheat times.
Longer cord length may also cause longer preheat times. We recommend using the shortest
outdoor rated extension cord that fits your outdoor grill setup. We recommend using only outdoor
extension cords marked as "SJOW" and "suitable for use with outdoor appliances."
For cords up to 25 feet, use 14 gauge. For 25- to 50-foot cords, use 12 gauge. Cords longer than
50 feet are not recommended.
While preheating is strongly recommended for best results, you can skip it by pressing and holding
the START/STOP button for 4 seconds. “ADD FOOD” will flash across the screen. Open the hood
and place ingredients in unit. Once the hood is closed, cooking will begin and the timer will start
counting down.
• Can I turn o Ninja Woodfire Flavor?
If you pressed WOODFIRE FLAVOR and already started your cooking function by pressing START/
STOP, you can press the WOODFIRE FLAVOR button again to turn it o if the ignition cycle is less
than 75% complete (indicated by the progress bar on the display screen). If pellets have fully ignited
and the grill has transitioned to the preheat cycle (indicated on the display screen), you cannot turn
o Ninja Woodfire Flavor Technology.
• Can I add more pellets during a cook cycle?
When using the Smoker function, you can add more pellets once the first batch has fully burned. Press
and hold the WOODFIRE FLAVOR button for 3 seconds to ignite new full box of pellets.
To run back-to-back smoking sessions, we recommend refilling the smoke box using the pellet scoop
when half the pellets have burned. DO NOT refill more than once or twice. DO NOT reignite pellets.
• Wi-fi troubleshooting
- Typical home Wi-Fi networks support both 2.4 GHz and 5 GHz.
- Do not use a VPN or a proxy server. Hotspot available to connect only at 2.4GHz.
- Make sure Wi-Fi isolation is turned o on the router.
- If you cannot connect, call 1- 855-427-5125.
• Still can't connect?
- Restart your phone.
- Turn o your phone, wait a few minutes, then turn it back on and connect to Wi-Fi.
- Reboot your grill.
- Unplug your grill for 10 seconds, then plug it back in and press the power button.
- Reboot your router.
- Unplug the router power cable for 30 seconds, then plug it back in. Allow several minutes for your
router to reboot completely.
• What should I do if I verified a wireless network password that is incorrect?
Close the app, then reopen it. Make sure to enter the correct Wi-Fi network password. In your phone's
network settings, choose your home 2.4 GHz network, and select Forget. Reconnect to your home
network. Make sure to use the correct password. (We recommend using the eye icon when entering your
password to make sure it is correct.) If you were able to connect to your home network, proceed to the
app setup process. Turn o your router and wait 30 seconds. Turn your router back on. Check to make
sure your 2.4 GHz network is visible in your phone settings. Turn o the grill, then wait 10 seconds. Turn
the grill back on. Hard-close the app and restart the connection process on the Grill. If you cannot locate
your Wi-Fi password, please contact your Internet service provider.
• What should I do if my username or password is invalid?
We recommend you select the eye icon next to the password entry to verify you are entering your
password correctly. Select the "Forgot Password" option on the sign-in page. The automated system
will email you a link to reset your password. If you do not see an email, search your inbox and spam
folder for emails from my[email protected]om. You can use the “Resend Email” option to
send the email again.
•
What should I do if there is an issue resetting password (did not receive the email or token was invalid)?
Select the "Forgot Password" option on the sign-in page. The automated system will email you a
link to reset your password. If you do not see an email, search your inbox and spam folder for emails
from mysharkninja@sharkninja.com. You can use the “Resend Email” option to send the email again.
NINJA COOKING CONNECTED GRILL
SharkNinja Operating LLC’s (“SharkNinja”) End-User License Agreement (“EULA”) is a legal agreement
between You (either a single entity or an individual) and SharkNinja for SharkNinja’s Software
Applications, including those installed by You onto your SharkNinja products or already installed on
your device, including all firmware (referred hereafter as “SN APPS”). By installing, copying, checking a
box, clicking a button confirming your agreement to these terms, or otherwise continuing to use the SN
APPS, You agree to be bound by the terms of this EULA. This license agreement represents the entire
agreement concerning SN APPS between You and SharkNinja, and it supersedes any prior proposal,
representation, or understanding between the parties. If You do not agree to the terms of this EULA,
do not install or use the SN APPS or this product. The SN APPS are protected by copyright laws and
international copyright treaties, as well as other intellectual property laws and treaties.
1. GRANT OF LICENSE. The SN APPS are licensed as follows:
1.1 Installation and Use. SharkNinja grants You the right to download, install, and use SN APPS on
the specified platform for which the SN APP was designed and in connection with SharkNinja
products with which the SN APPS are designed to operate (“SN Devices”).
1.2 Backup Copies. You may also make a copy of SN APPS downloaded and installed by You for
backup and archival purposes.
2. DESCRIPTION OF OTHER RIGHTS AND LIMITATIONS.
2.1 Maintenance of Copyright Notices. You must not remove or alter any copyright notices on any
and all copies of the SN APPS.
2.2 Distribution. You may not distribute copies of the SN APPS to third parties.
2.3 Prohibition on Reverse Engineering, Decompilation, and Disassembly. You may not reverse
engineer, decompile, or disassemble SN APPS, except and only to the extent that such activity is
expressly permitted by applicable law notwithstanding this limitation.
2.4 Rental. You may not rent, lease, or lend SN APPS without written permission from SharkNinja.
2.5 NOT FOR RESALE SOFTWARE. Applications identified as “Not for Resale” or “NFR,” may not be
resold, transferred, or used for any purpose other than demonstration, test, or evaluation.
2.6 Support Services. SharkNinja may provide You with support services related to SN APPS
(“Support Services”). Any supplemental software code provided to You as part of the Support
Services shall be considered part of SN APPS and subject to the terms and conditions of this
EULA.
2.7 Compliance with Applicable Laws. You must comply with all applicable laws regarding use
of SN APPS.
3. UPDATES.
SharkNinja may provide You with upgrades or updates to SN APPS. This EULA will govern any
upgrades provided by SharkNinja that replace and/or supplement SN APPS, unless such upgrade is
accompanied by a separate EULA, in which case the terms of that EULA will govern. If You decide
not to download and use an upgrade or update provided by SharkNinja, You understand that You
could put SN Apps at risk to serious security threats or cause SN Apps to become unusable or
unstable.
IMPORTANT: PLEASE READ THE TERMS AND CONDITIONS OF THIS LICENSE AGREEMENT
16 17
ninjakitchen.com
ninjakitchen.com
NINJA COOKING CONNECTED GRILL – CONT'D
4. DATA AND PRIVACY.
SharkNinja is committed to ensuring your privacy by adhering to high standards of fairness and
integrity. We are committed to keeping our customers informed about how we use the information
we gather from You through the use of each of our websites or SN APPS. Our privacy practices are
described in SharkNinja’s Privacy Policy, as well as in separate notices given when an app, product,
or service is purchased or downloaded. By using SN APPs or providing us with your personal
information, You are accepting and consenting to the practices, terms, and conditions described
in SharkNinja’s Privacy Policy. At all times your information will be treated in accordance with the
SharkNinja Privacy Policy, which is incorporated by reference into this EULA and can be viewed at
the following URL: http://www.sharkninja.com/privacypolicy.
5. THIRD-PARTY APPLICATION LIBRARIES AND EMBEDDED SOFTWARE.
5.1 You acknowledge that Ayla Networks, Inc. (“Ayla”) has provided certain application libraries that
have been embedded into SN APPS (“Ayla Application Libraries”) and enables SN Devices to
connect to the Ayla Cloud Service (“Ayla Embedded Software”).
5.2 You will not use the Ayla Application Libraries except as an incorporated portion of SN APPS,
unmodified from the form provided to You.
5.3 You will not use the Ayla Embedded Software except as an incorporated portion of SN Devices,
unmodified from the form provided to You.
5.4 You will not modify, adapt, translate, or create derivative works based on, or decompile,
disassemble, reverse engineer, or otherwise attempt to derive the source code or underlying
algorithms of, the Ayla Application Libraries or the Ayla Embedded Software.
5.5 SharkNinja retains all ownership of SN APPS (and the Ayla Application Libraries contained
therein) and any software installed on SN Devices (including the Ayla Embedded Software) and
only a license thereto is granted to You for use in connection with the SN APPS and SN Devices.
5.6 You will not use the Ayla Application Libraries or Ayla Embedded Software to attempt to gain
unauthorized access to or use of the systems/services of SharkNinja’s other licensors; nor will
You transmit viruses, worms, Trojan horses, time bombs, spyware, malware, cancelbots, passive
collection mechanisms, robots, data mining software, or any other malicious or invasive code or
program into the systems/services of SharkNinja’s other licensors.
5.7 You will not use the Ayla Application Libraries or Ayla Embedded Software to interfere with,
breach, or circumvent any security feature, authentication feature, or any other feature that
restricts or enforces limitations on the use of, or access to, the systems/services of SharkNinja’s
other licensors.
5.8 You will not probe, attack, scan, or test the vulnerability of the systems/services of SharkNinja’s
other licensors.
5.9 SharkNinja’s other licensors of the SN APPS, Ayla Application Libraries, and the Ayla Embedded
Software are the express third-party beneficiaries of this EULA, and the provisions of this Section
of this EULA are made expressly for the benefit of such licensors, and are enforceable by such
licensors.
6. TERMINATION.
Without prejudice to any other rights, SharkNinja may terminate this EULA if You fail to comply with
the terms and conditions of this EULA. In such event, You must destroy all copies of SN APPS in your
possession.
8. OPEN SOURCE SOFTWARE.
You hereby acknowledge that SN APPS may contain software that is subject to “open source”
or “free software” licenses (“Open Source Software”). The license granted by this EULA does not
apply to Open Source Software contained in the SN APPS. Rather, the terms and conditions in
the applicable Open Source Software license shall apply to the Open Source Software. Nothing in
this EULA limits your rights under, or grants You rights that supersede, any Open Source Software
license. You acknowledge that the Open Source Software license is solely between You and the
applicable licensor of the Open Source Software. To the extent the terms of the licenses applicable
to the Open Source Software require SharkNinja to provide the Open Source Software, in either
source or executable form, or to provide copies of applicable license terms or other required
information, You may obtain a copy of the software by contacting SharkNinja at the below physical
address. Additional information about the Open Source Software, and its terms of use, may be found
at www.sharkclean.com/opensource.
9. NO WARRANTIES.
SharkNinja expressly disclaims any warranty for SN APPS, Ayla Application Libraries, or Ayla
Embedded Software. SN APPS, Ayla Application Libraries, and Ayla Embedded Software are
provided ‘As Is’ without any express or implied warranty of any kind, including but not limited to any
warranties of merchantability, noninfringement, fitness of a particular purpose, or title. SharkNinja
does not warrant or assume responsibility for the accuracy or completeness of any information,
text, graphics, links, or other items contained within the SN APPS. SharkNinja makes no warranties
respecting any harm that may be caused by the transmission of a computer virus, worm, logic
bomb, or other such computer program. SharkNinja further expressly disclaims any warranty or
representation to any third party.
10. LIMITATION OF LIABILITY.
In no event shall SharkNinja or its suppliers be liable for any special, incidental, punitive, indirect,
or consequential damages whatsoever (including, but not limited to, damages for loss of profits or
confidential or other information, for business interruption, for personal injury, for loss of privacy,
for failure to meet any duty including of good faith or of reasonable care, for negligence, and for
any other pecuniary or other loss whatsoever) arising out of or in any way related to the use of
or inability to use SN Devices or SN APPS, the provision of or failure to provide support or other
services, information, software, and related content through the product or otherwise arising out
of the use of SN APPS, or otherwise under or in connection with any provision of this EULA, even
in the event of the fault, tort (including negligence), strict liability, breach of contract, or breach of
warranty of SharkNinja or any supplier, and even if SharkNinja or any supplier has been advised of
the possibility of such damages. SharkNinja shall have no liability with respect to the content of the
SN APPS or any part thereof, including but not limited to errors or omissions contained therein, libel,
infringements of rights of publicity, privacy, trademark rights, business interruption, personal injury,
loss of privacy, moral rights, or the disclosure of confidential information.
11. APPLICABLE LAW.
The laws of the Commonwealth of Massachusetts will govern this EULA and You hereby consent
to exclusive jurisdiction and venue in the state and federal courts sitting in the Commonwealth of
Massachusetts.
12. ASSIGNMENT.
SharkNinja may assign this EULA without notice to Licensor.
13. ENTIRE AGREEMENT.
This EULA (including any addendum or amendment to this EULA which is included with the
SN Devices) is the entire agreement between You and SharkNinja relating to the SN APPS
and supersedes all prior or contemporaneous oral or written communications, proposals and
representations with respect to the SN APPS or any other subject matter covered by this EULA. To
the extent the terms of any SharkNinja policies or programs for support services conflict with the
terms of this EULA, the terms of this EULA shall control. If You have questions regarding this EULA,
please contact SharkNinja at 89 A Street, Suite 100, Needham, MA 02494.
IMPORTANT: PLEASE READ THE TERMS AND CONDITIONS OF THIS LICENSE AGREEMENT
CAREFULLYBEFORE CONTINUING WITH THIS PROGRAM INSTALL OR USE OF THIS PRODUCT:
19
ninjakitchen.com
18
ninjakitchen.com
The One (1) Year Limited Warranty applies to purchases made from authorized retailers of
SharkNinja Operating LLC. Warranty coverage applies to the original owner and to the original
product only and is not transferable.
SharkNinja warrants that the unit shall be free from defects in material and workmanship for a period
of one (1) year from the date of purchase when it is used under normal household conditions and
maintained according to the requirements outlined in the Owner’s Guide, subject to the following
conditions and exclusions:
What is covered by this warranty?
1. The original unit and/or non-wearable parts deemed defective, in SharkNinja’s sole discretion,
will be repaired or replaced up to one (1) year from the original purchase date.
2. In the event a replacement unit is issued, the warranty coverage ends six (6) months following
the receipt date of the replacement unit or the remainder of the existing warranty, whichever is
later. SharkNinja reserves the right to replace the unit with one of equal or greater value.
What is not covered by this warranty?
1. Normal wear and tear of wearable parts (such as blending vessels, lids, cups, blades, blender
bases, removable pots, racks, pans, etc.), which require regular maintenance and/or replacement
to ensure the proper functioning of your unit, are not covered by this warranty. Replacement
parts are available for purchase at ninjaaccessories.com.
2. Any unit that has been tampered with or used for commercial purposes.
3. Damage caused by misuse, abuse, negligent handling, failure to perform required maintenance
(e.g., failure to keep the well of the motor base clear of food spills and other debris), or damage
due to mishandling in transit.
4. Consequential and incidental damages.
5. Defects caused by repair persons not authorized by SharkNinja. These defects include damages
caused in the process of shipping, altering, or repairing the SharkNinja product (or any of its parts)
when the repair is performed by a repair person not authorized by SharkNinja.
6. Products purchased, used, or operated outside North America.
How to get service
If your appliance fails to operate properly while in use under normal household conditions within the
warranty period, visit ninjakitchen.com/support for product care and maintenance self-help. Our
Customer Service Specialists are also available at 1-855-427-5125 to assist with product support and
warranty service options, including the possibility of upgrading to our VIP warranty service options
for select product categories. So we may better assist you, please register your product online at
registeryourninja.com and have the product on hand when you call.
SharkNinja will cover the cost for the customer to send in the unit to us for repair or replacement. A fee
of $20.95 (subject to change) will be charged when SharkNinja ships the repaired or replacement unit.
How to initiate a warranty claim
You must call 1-855-427-5125 to initiate a warranty claim. You will need the receipt as proof of purchase.
We also ask that you register your product online at registeryourninja.com and have the product on
hand when you call, so we may better assist you. A Customer Service Specialist will provide you with
return and packing instruction information.
How state law applies
This warranty gives you specifi c legal rights, and you also may have other rights that vary from state
to state. Some states do not permit the exclusion or limitation of incidental or consequential damages,
so the above may not apply to you.
ONE (1) YEAR LIMITED WARRANTY
NJA_1_YR_IB_LMTD_WRNTY_US_ENG_OUTDOOR
NOTES
@ninjakitchen
SharkNinja Operating LLC
US: Needham, MA 02494
1-855-427-5125
ninjakitchen.com
Illustrations may dier from actual product. We are constantly striving to improve our products,
therefore the specifications contained herein are subject to change withoutnotice.
NINJA WOODFIRE is a trademark of SharkNinja Operating LLC.
This product may be covered by one or more U.S. patents. See sharkninja.com/patents for more information.
© 2023 SharkNinja Operating LLC
OG900Series_IB_REV_Mv4
TECHNICAL SPECIFICATIONS
Voltage: 120V~, 60Hz
Power: 1760 Watts
RECORD THIS INFORMATION
Model Number: ____________________
Serial Number: _____________________
Date of Purchase: ___________________
(Keep receipt)
Store of Purchase: __________________
REGISTER YOUR PURCHASE
registeryourninja.com
Scan QR code using mobile device
THANK YOU FOR PURCHASING THE NINJA WOODFIRE™
PRO XL OUTDOOR GRILL & SMOKER WITH BUILT-IN
THERMOMETER
FCC WARNINGS
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to parts 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential installa-
tion. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and
accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will
not occur in a particular installation. If this equip-
ment does cause harmful interference to radio or
television reception, which can be determined by
turning the equipment o and on, the user is en-
couraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment
and receiver.
- Connect the equipment into an outlet on a
circuit dierent from that to which the receiver
is connected.
- Consult the dealer or an experienced radio/TV
technician for help.
This device complies with part 15 of the FCC rules.
Operation is subject to the following conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received,
including interference that may cause undesired
operation.
Changes or modifications not expressly approved by
the party responsible for compliance could void the
user’s authority to operate this device.
ISED STATEMENT
This device complies with Industry Canada license-
exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not
cause interference, and (2) this device must accept
any interference, including interference that may
cause undesired operation of the device.
