Contents
Page
Important Safeguards 3
Know Your Futura Electronic Kettle 5
Specifications 6
Ideal For 6
Trial Run 7
How to Use 7
High Altitude Use 10
How to Clean 11
Descaling 11
Troubleshooting 12
Guarantee Card back cover
2
© 2025 and All Rights Reserved. 'Futura' and 'Hawkins' are the Registered Trademarks of
Hawkins Cookers Limited in India and in various other countries throughout the world.
CIN: L28997MH1959PLC011304.
Hawkins Cookers Limited
Udyog Mandir 2, Pitamber Lane, Mahim, Mumbai 400 016, INDIA
TEL (91 22) 2444 0807 FAX (91 22) 2444 9152
EMAIL: kit[email protected]n
WEBSITE: www.hawkinscookers.com
Any Questions or Comments?
Contact:
3
Important Safeguards
1. Read all instructions before use.
2. Do not use the Kettle for any use other than its intended use.
3. Do not use the Kettle on any other base or stand – use only on the power base
provided.
4. Do not immerse cord, plugs or Kettle/base in water or other liquid, to protect against
fire, electric shock, equipment damage and injury. Do not operate the Kettle with wet
hands/gloves.
5. This appliance incorporates an earth connection for functional purposes.
6. Do not touch hot surfaces – use the handle/knob. Handle with care at all times.
7. Do not open the lid during a boiling cycle – this may cause scalding. To avoid burns
and risk of personal injury, use extreme caution when moving hot liquid contents.
8. Do not operate the Kettle on an inclined surface – always use a dry, level surface well
away from edges.
9. Do not operate the Kettle if body, cord or plug is damaged, or if the handle is loose.
Do not operate the Kettle if the cord or plug is damaged, if it malfunctions, or if it is
dropped or damaged in any manner. Do not try to open or repair the Kettle yourself –
return it to an Authorised Service Centre for inspection, adjustment or repair.
10. Do not overfill the Kettle above the maximum level marking (1.4L). If the kettle
is overfilled, boiling water may be ejected. Do not underfill the Kettle below 1 cup/
240 ml – ensure that the water covers the temperature sensor (which is located on the
inside base, near the handle).
11. Do not allow the Kettle to boil dry. Do not switch it ON if it is empty.
4
12. Do not place the Kettle or cord on or near a hot gas or electric burner, in a heated
oven, or in a microwave. Do not let the cord hang over the table or counter edge, where
it can snag or trip unintentionally. Untie knots and/or untangle cord before use.
13. The Kettle is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities or lack of experience and knowledge, unless they
have been given supervision or instructions concerning use of the appliance by a person
responsible for their safety. Children should be supervised to ensure that they do not play
with the appliance.
14. Unplug from socket when not in use and before cleaning. Allow to cool before
handling and cleaning.
15. To operate, always insert plug into the power outlet and then turn the power switch
ON. To disconnect, turn power switch to OFF, then remove plug from power outlet.
16. Dissolved substances in water or other Kettle contents may deposit and stain the
inside surface. This is not a material defect. Follow the cleaning/descaling instructions
provided herein to remove or minimize the stains to the extent possible.
17. Do not point the Kettle spout during its operation towards walls, cabinets or other
objects that may be affected by steam.
18. Do not drink directly from the Kettle. The Kettle and contents inside may be very hot.
19. Do not wash the Kettle or any of its parts in a dishwasher. Hand wash only. Do not
clean the Kettle with harsh cleansers, steel wool pads, or other abrasive materials.
20. Do not use the Kettle to store food or any other items, when not in use, wash and
wipe dry before storing.
21. This appliance is designed for regular domestic use.
22.
SAVE THESE INSTRUCTIONS.
5
Know Your Futura Electronic Kettle
6
Specifications
Capacity 1.4 Litre
Power consumption 1200 W
Plug and Wire 6A standard plug
Operating voltage 220V AC, 50 Hz
Guarantee 1 Year
Ideal For
Trial Run
•
Remove all packaging material.
•
Check and confirm that the available power voltage complies with the rated Kettle voltage
of 220V AC and that the power outlet can bear the rated load of 1200 Watts and is
properly earthed.
•
Remove lid. Clean and wash Kettle. Add water up to '1.4L' marking.
•
Place Kettle on power base on a flat, level surface.
•
Safely plug the power-supply cord into the power outlet.
•
Set target temperature to boil water (see "How to Use" below).
•
Once target temperature is reached, wait 2 minutes. Turn off Kettle.
•
Discard boiled water – do not consume.
•
Your Kettle is now ready to use.
How to Use
POWER BASE WITH 360° ACCESS
•
Release cord from under power base and adjust length to reach the power outlet.
FILLING
•
Remove the Kettle from the Power Base before filling.
•
Open lid and fill Kettle to desired level:
a. Do not fill less than 1 cup/240 ml of water, to prevent the Kettle running dry, which
will shorten its life.
b. Do not fill more than 5 cups/1.2 litres of water (up to the 1.2L marking) if using
steam mode: boiling water may be ejected, causing burns.
c.
Do not fill more than 6 cups/1.4 litres of water (up to the 1.4L marking) in regular
mode: if overfilled, boiling water may be ejected, causing burns.
7
TURNING THE KETTLE ON/OFF
•
Plug Power Base into the power outlet and turn power ON. The LED Indicator (above the
Power Button) will glow red and the LED Display will display "Open".
•
Place Kettle (filled with contents) on Power Base. The LED Display will show the current
ambient temperature inside the Kettle.
•
Press the Power Button. The LED Indicator will turn green, and the Kettle will beep. The
Kettle is now Switched ON. If you do not set any temperature, the Kettle will boil the
liquid contents up to 100°C at sea level and maintain temperature for 60 minutes.
•
To switch OFF the Kettle, press the Power Button. The LED Indicator will turn red and the
LED Display will show the present temperature of the liquid contents.
SETTING TARGET TEMPERATURE
1. Switch Kettle ON. By default, the temperature is set at 100°C (the maximum). Turn
Temperature Control Knob to set your target temperature (anticlockwise lowers temperature,
clockwise raises temperature). Once set, the LED Display will blink, the Kettle will beep
once and show the set temperature for a moment, and then start heating to reach the set
temperature. For example, you want water to be heated to 70°C, turn Knob anticlockwise
till the display shows "S 70". After a second the display will blink twice, indicating that the
target temperature is set at 70°C. Once the Kettle reaches the target temperature, it will
beep thrice and shift to 'Keep Warm' mode.
2. In Keep Warm mode, the Kettle will maintain the target temperature for 60 minutes,
and will beep periodically after every 5 minutes as a reminder.
3. To change the Keep Warm time, press knob once – the LED Display will show
"A 60". Turn the knob clockwise or anticlockwise to set the desired time (maximum
16 hours 30 minutes). The LED Display will blink twice (within 2 seconds if the said time is
changed, or 5 seconds if it is not). After the set Keep Warm time, the unit will beep thrice
and the Kettle will Switch OFF automatically. The LED Indicator will turn red.
4. Turn knob at any time during operation to change the target temperature – the Kettle
8
will beep once and display the new temperature (80°C, for example, will be displayed as
"S 80").
STEAM MODE
Turning the knob clockwise beyond 100°C will shift Kettle into Steam mode (the LED
Display will show "S St") in which the Kettle will keep boiling the water for up to 10 minutes,
after which it will beep thrice and switch OFF automatically. The LED Indicator will turn red
and the LED Display will show the current temperature of the Kettle contents.
ADDITIONAL INSTRUCTIONS
•
To reach a target temperature lower than the current temperature, consider adding some
cold water to speed up the process.
•
The LED Display will show the temperature progression till the target temperature is
reached.
•
Be watchful for steam that is likely to emerge from the spout. Keep spout pointed away
from your person.
•
The Water Temperature Sensor (a small sensor sitting atop the inside base, towards handle)
constantly monitors the temperature of the contents inside the Kettle. The Sensor will
not work properly if there is insufficient water in the Kettle (less than 1 cup/240 ml). As
a thumb rule, ensure that it remains covered by liquid throughout operation.
BOIL-DRY PROTECTION
•
"Boil-Dry" occurs when the liquid contents fall to an unacceptably low level, which can
cause the heating element to burn out if not handled promptly and properly.
•
A boil-dry event will switch the Kettle OFF automatically. The LED Display will show "dry"
and the LED indicator will turn red.
•
Immediately remove Kettle from the Power Base to reset the device.
•
Set the Kettle down on a suitable surface and wait 5 minutes. Add minimum 1 cup/
240 ml water at room (or cooler) temperature before restarting.
9
High Altitude Use
Water boils at a lower temperature at high altitude owing to lower atmospheric pressure.
At sea level, water boils at 100°C/212°F. It is estimated that, for every 500 feet/152 metres
of altitude gain, the boiling point reduces by approximately 0.5°C/0.9°F. When using this
Kettle at a high altitude, we recommend that you follow the guidelines given in the table
below, making adjustments to suit the ambient conditions as desired by you.
Altitude
(ft/m)
Boiling Point of
Water
(°C/°F)
0 ft/0 m 100°C/212°F
500 ft/150 m 99.5°C/211.1°F
1000 ft/305 m 99°C/210.2°F
2000 ft/610 m 98°C/208.4°F
5000 ft/1524 m 95°C/203°F
6000 ft/1829 m 94°C/201.1°F
8000 ft/2438 m 91.9°C/197.4°F
10000 ft/3048 m 89.8°C/193.6°F
12000 ft/3658 m 87.6°C/189.8°F
14000 ft/4267 m 85.5°C/185.9°F
10
How to Clean
•
Unplug the Kettle and allow to cool naturally before cleaning.
•
Use a soft damp cloth to wipe the Kettle body and its Power Base. Do not allow the
electric socket on the exterior base of the Kettle – to get wet, sit on a wet
counter, or be wiped with a wet cloth.
•
Never immerse Kettle or its Power Base in water.
•
Dry all parts after each use.
•
Do not wash Kettle or any of its parts in a dishwasher. Hand wash only.
•
If food is stuck in the Kettle, fill to maximum level with water. Bring to boil. Allow to
cool naturally. Empty out water. Clean with a non-abrasive kitchen cleanser and a plastic
scrubber. Wash and wipe dry.
•
Be very gentle when cleaning the temperature sensor inside to avoid damage.
Descaling
Scaling is a naturally occurring build up generally caused by mineral deposits present in
hard water. Descaling the Kettle regularly can increase the useful life of the Kettle, allowing it
to boil water faster with less energy. The ideal descaling cycle depends on the water hardness.
The guarantee is void if descaling is not carried out in accordance with these instructions. If
scale deposits build up inside the Kettle, please follow these steps to descale it:
1. Squeeze half a lemon or add
1
/2 cup/120 ml of distilled vinegar into the Kettle.
2. Add 2 cups/480 ml of fresh water. Bring the mixture to a boil.
3. Let mixture cool about 15 minutes to loosen the deposits, then pour out contents.
4. Use a soft damp cloth, sponge or brush to clean off any remaining deposits.
5. Rinse inside surface thoroughly with fresh water.
11
Troubleshooting
The Power Base won’t turn on.
•
Make sure the power cord is securely plugged into the power outlet.
•
Check that the outlet is in working condition – test in another outlet as a cross check.
•
Check and reset the MCB if it has tripped.
•
If using an extension board with multiple connections, detach other connections prior
to retrying.
The Kettle does not heat up.
•
If the LED Display shows "Open", ensure the Kettle is properly seated on the Power Base.
•
If the LED Display shows "dry", overheat control may have tripped. Follow the instructions
in "BOIL DRY PROTECTION" on page 9 to re-use.
The Kettle is not reaching the target temperature.
•
If the Kettle doesn’t reach the target temperature, but operates for an unusually long
time at a temperature lower than the target temperature without reaching the target
or shutting off, it may be due to scaling or hard water. Read and follow "Descaling"
instructions.
12
Space for Your Notes
13
