USER MANUAL
xtrovac 910
Pool Vacuum Cleaner
ENGLISH
1
SAFETY WARNINGS & INSTRUCTIONS
Information contained in this Instruction Manual will help you operate the item safely, protect
yourself and others from hazards, and prevent damage to the device and other property.
Remark: Depending on the model you own, accessories/ parts
shown in this manual are not necessarily included in every model.
Product/parts in photos/drawings may vary with the model purchased.
Check the spare parts drawing to understand the parts included in your
model purchased.
SAVE THESE INSTRUCTIONS
WARNING!
- This is not a TOY. Children should be kept out of reach from this pool
vacuum and its accessories.
- Never allow children to operate this product.
- This appliance is not intended for use by persons with reduced
physical, sensory, mental capabilities, or a lack of experience and
knowledge, unless they are given supervision or instructions
concerning the safe use of the appliance and understand the hazards
involved by a person responsible for their safety.
- Children must not play with this product.
- Cleaning and user maintenance must not be carried out by children.
- Make sure the pool vacuum is fully immersed in water before
initiating operation. The minimum water level required to operate
the pool vacuum must cover the entire pool vacuum. Operating the
pool vacuum when it is not immersed in the water correctly could
damage the unit and void the warranty as a result.
- Maximum operating depth in water is 3 meters (9.8ft.).
- Operating water temperature: 5°C (41°F) –35°C (95°F).
- Detachable supply unit (external adaptor).
- The pool vacuum is only to be recharged with external adaptor and
charging plug delivered with this product.
- For the purposes of recharging the battery, only use the detachable
supply unit that provided with this pool vacuum to charge the
battery.
- Connect the external adaptor to a power source through a residential
current device (RCD) / a ground fault circuit interrupter (GFCI). If in
doubt, consult a qualied professional electrician.
- DO NOT use this pool vacuum if any damage is detected.
- Replace damaged parts with ones that are certied by the distributor
or manufacturer.
ENGLISH
2
- Turn o the power, disconnect the external adaptor from the power
source, and unplug the external adaptor from the charging plug
before detaching the pool vacuum from the charging plug.
- Disconnect the pool vacuum from the supply mains and make sure
the pool vacuum is powered OFF prior to servicing it such as cleaning
the lter bag.
- DO NOT attempt to replace the installed rechargeable Li-ion battery
pack.
- DO NOT handle the pool vacuum, external adaptor and charging
plug while it is charging with wet limbs and without shoes.
- You should not operate this pool vacuum when people/pets are
present in the water.
- DO NOT use this pool vacuum without an intact lter bag in place,
otherwise your warranty will be voided as a result.
- Suction entrapment hazard: This pool vacuum generates suction.
Do not allow hair, body, and any loose parts of your clothing to
make contact with the suction point of the pool vacuum during its
operation.
- Never insert body parts, clothing, and other objects into the openings
and moving parts of the pool vacuum.
- DO NOT use this pool vacuum to pick up any toxic substance,
ammable, and combustible liquids (i.e. gasoline) in the presence of
explosive or ammable fumes.
- Under no circumstances should you attempt to disassemble the pool
vacuum and replace the impeller, motor, and battery by yourself.
- Never insert ngers and any object to touch the impeller.
- The built-in battery must be removed by a skilled technician before
it is scrapped.
- This pool vacuum contains a battery that are only to be removed by
skilled persons.
- The pool vacuum must be disconnected from the supply mains as
the battery is removed.
- For details regarding battery recycling/disposal, refer to the section
“BATTERY DISPOSAL” in this manual and contact your local authorities
for more information.
- The battery must be disposed safely in accordance with local
ordinances or regulations.
- External adaptor and charging plug:
· Never use the external adaptor and charging plug for anything
other than charging the battery of the pool vacuum that is supplied
in the same pack.
ENGLISH
3
· The external adaptor and charging plug should not be used
outdoors, nor should it be exposed to rain, humidity, any liquid or
heat.
· The transformer (or external adaptor) is to be located outside zone 1.
· Keep the external adaptor and charging plug out of reach of
children.
· Never use the external adaptor and charging plug if any damage is
detected.
· DO NOT handle the external adaptor and charging plug with wet
hands.
· Keep the external adaptor disconnected from power when it is not
in use.
· Never attempt to open the external adaptor and charging plug.
· If the supply cord of the external adaptor is damaged, the external
adaptor must be replaced by the manufacturer or its service agent
to prevent hazards of any kind.
· Make sure the pool vacuum and the charging plug are completely
dry before charging.
CAUTION!
- This pool vacuum is designed for underwater use only; it is not an all-purpose vacuum cleaner. DO
NOT attempt to use it to clean anything other than your pool.
- Use only original accessories delivered with this product.
- DO NOT use this pool vacuum right after pool-shocking. It is recommended to rst leave the pool
circulating for at least 24-48 hours.
- If you are planning on using the pool vacuum in a saltwater pool, make sure all salt are dissolved
before placing it in the water.
- DO NOT use this pool vacuum with another automatic cleaner/cleaner simultaneously in the pool/spa.
- Avoid picking up hard, sharp objects with this product as they may damage the pool vacuum and lter.
- To avoid damaging the external adaptor and charging plug, do not attempt to carry the pool vacuum
by the cable of external adaptor or pull the cable in hopes of disconnecting it from the power source
and charging plug.
- Charge the pool vacuum indoors in a clean, dry area with good ventilation and away from sunlight.
- DO NOT leave the pool vacuum charged for over 10 hours.
- If the pool vacuum will not be used for an extended period, detach it from the charging plug and
use a damp cloth to clean and dry the pool vacuum and its accessories. Make sure to charge the pool
vacuum to about 30% to 50% of the battery capacity before it is stored. Store in a well-ventilated area
away from sunlight, heat, ignition sources, pool chemicals, and children. Recharge the pool vacuum
every three months.
- All actions concerning the disassembly of the main unit (i.e. battery disposal) can only be carried by
an authorized technician.
Above warnings and cautions are not intended to incorporate
all possible instances for risks and / or severe injuries. Pool / spa
owners should always exercise extra caution and common sense when
utilizing the product.
ENGLISH
4
1. Place the unit on a at surface.
Set the pool vacuum to
Power O/ Charging Mode by
turning the switching knob
anticlockwise until it clicks
and completely exposes the
charging port.
2. Align and attach the charging
plug to the charging port.
WARNING! Be sure not to invert
the charging plug and ensure
both the charging plug and
charging port are clean and dry
before charging them. TIPS: Use
cotton bud to dry the charging
port and pins. Plug the charging
cable of the external adaptor
into the charging plug.
GETTING STARTED
Charging The Battery
IMPORTANT NOTE: Fully charge the pool vacuum (about 6 hrs) before
using it for the rst time.
WARNING!
- Use only the original external adaptor and charging plug provided.
- Make sure the pool vacuum and the charging port are clean and
dry before set-up and charging. (TIPS: use a cotton bud to dry the
charging port and charging pins)
- The charging pins are waterproof. However, remnants of water in
the port and around the pins could result in natural occurrence of
stains (a byproduct of chemical reaction between water and electric
currents). Otherwise, the stains can be removed by light scrubbing
with a cotton bud soaked with juice of lemon or vinegar.
ENGLISH
5
3. Connect the external adaptor to the power source. The indicator light
on the external adaptor will turn red when the vacuum is charging
and green when it is fully charged. Charge it for 5-6 hours for best
performance.
· Immediately disconnect the external adaptor from the power source
if you detect any of the following:
- Oensive or unusual odor
- Excessive heat
- Deformation, cracks, leaks
- Smoke
4. When charging is complete, disconnect the external adaptor from
the power source and unplug the charging cable from the charging
plug. Detach the charging plug from the main unit. WARNING! Never
leave the charging plug while the pool vacuum is in the water.
Normally the pool vacuum is designed to operate for up to 75 minutes
on a full charge.
Note: Empty the lter bag regularly. Excessive debris increases the
burden to the motor and may shorten the operating time.
NOTE: Rechargeable lithium-ion battery is classied as a consumable item.
It has a limited life and will gradually lose its capacity to hold a charge.
Therefore, the running time of the pool vacuum will gradually reduce after
repeated charging and discharging throughout its product life.
Once the lifespan of the battery reaches its end, refer to section “BATTERY
DISPOSAL” for instructions regarding battery disposal.
NOTE: Let the pool vacuum rest for around 30 to 40 minutes before
charging it again.
5-6h
RED light - Charging
GREEN light - Charged
ENGLISH
6
Set-Up Before Use
This pool vacuum has removable extensions which can be removed to clean the narrow areas.
Side Extension Assembly
IInsert the stem of the wing to the hole on the side of the main body. Turn the wing and press on it to
secure it to the main body. You will hear a “click” sound.
Side Extension Disassembly
Reverse the steps to disassemble the extension from the main unit.
Telescopic pole connector / telescopic pole (not included) assembly (for EU & US only)
Align and insert the pole connector into the post as shown. Slide the telescopic pole into the pole
connector until the holes on the side of the telescopic pole are secured to the pins of the pole connector.
Click
1
2
ENGLISH
7
Pool Preparation
- If the liner is brittle, damaged, or wrinkled, contact a qualied professional to perform the necessary
repairs or perform a liner replacement prior to using the pool vacuum.
- If you are using a saltwater pool, make sure all salt are dissolved before placing the pool vacuum
into the water.
Specic telescopic pole connector/specic pole (not included) assembly (for Australia/New
Zealand only)
Align and insert the pole connector into the post as shown. Press on the internal wishbone clip
(preinstalled inside the specic telescopic pole) to retract its side pins. Slide the specic telescopic
pole into the specic pole connector until it’s locked in place by the side pins and holes.
1
2
1
2
ENGLISH
8
OPERATION
1) Bring your pool vacuum to the side of your pool. Turn the switching knob clockwise until it clicks to
expose the water sensors. The light at the top will turn blue. Immerse the pool vacuum into water,
the light turns immediately to green and the impeller will start to turn after 4-5 seconds.
2) To retrieve the pool vacuum, bring it poolside and ip it upside down before lifting. This is done to
prevent debris from scattering back into the pool (especially if you are using the ne lter bag) and
avoid bending the pole in the process.
3) Rinse the pool vacuum with fresh water after every use. DO NOT use any aggressive detergent.
4) Dry the charging port and pins thoroughly (TIPS: Use cotton bud to dry them).
To eectively vacuum up debris, ensure the pool vacuum is laid at on the pool oor as you steer
it back and forth in regular motion over debris patches for collection. Debris is collected from the
front, side and back to ll up the lter bag.
Excess dirt and debris in the pool could clog the impeller, which would automatically stop to protect
the motor, and the indicator light would turn red. Remove the vacuum from the pool and turn it o
prior to unclogging and emptying the lter bag if it is full. To resume operation, turn the switching
knob anticlockwise until Power O is selected, then turn it clockwise to select Power On.
Once the pool vacuum is out of the water, the impeller will cease to spin within 2-3 seconds. The
LED light will turn blue. When battery level is running low, blue light will ash.
Light
Light Color
Blue Power On (ready for operation)
Blue - Flash Battery level is running low
Green In operation
Green - Flash Battery level is running low.
Green light O Battery depleted (need to be recharged)
Red Impeller stops (impeller clogged)
ENGLISH
9
Vacuuming the Sunken Compartment of an Automatic Slatted Cover
WARNING! Pay attention to all safety warnings in the manual
of your automatic slatted cover concerning this cleaning
operation beforehand.
- The minimum distance required for the immersion of the vacuum into the sunken compartment is
30cm (12in).
- Remove the duckboard and unroll the pool slat according to instructions from your pool cover
manual.
- Detach one extension of the vacuum cleaner before immersing it into the pool.
- Attach a telescopic pole (not provided) to the pool vacuum handle as instructed in the manual.
- Power on the vacuum then align it as shown in the image above before immersion.
- Once the cleaner reaches the pool oor, parallel it to the pool length as shown above and start
vacuuming the sunken compartment.
ENGLISH
10
EMPTYING THE FILTER BAG
CAUTION! Make sure the pool vacuum is OFF before cleaning the lter bag. Place the cleaner on a at
surface. Press on the cord fastener to release the bag from the main body. It is recommended to clean
the lter bag with splashing water. If brushing is deemed necessary, use only a soft brush to clean it
carefully and gently to avoid any damages.
MAINTENANCE & STORAGE
NOTE:
1. Be sure to clean and dry the areas around the charging port and water sensors after every use to
avoid the forming of stains (byproduct of a natural chemical reaction between electric current and
water). Otherwise, the stains can be removed by light scrubbing with a cotton bud soaked with
juice of lemon or vinegar.
2. Battery discharges on its own during storage. Make sure to charge the pool vacuum to about 30%
to 50% of the battery capacity before it is stored.
3. You must recharge the battery at least once every three months when it is not in use.
- Unplug the external adaptor from the socket and the charging cable from the charging plug.
- Detach accessories from the pool vacuum. If necessary, rinse the pool vacuum and accessories with
fresh water. DO NOT use aggressive detergent.
- Be sure to dry the pool vacuum before storage.
- Use a damp cloth to clean and dry the pool vacuum and its accessories.
- Store them in a well-ventilated area away from sunlight, heat, ignition sources, pool chemicals, and from
children. Ambient temperature for storage should be 10°C – 25°C (50°F – 77°F). NOTE: A higher storage
temperature may reduce the battery life.
WARNING!
Under no circumstances should you attempt to disassemble the
main unit and replace the impeller, motor, and battery by yourself.
CAUTION!
- Excessive heat can damage the battery and reduce the lifespan of your pool vacuum as a result.
- Consult your dealer regarding battery replacement if the following happens:
· Battery does not charge fully.
· Battery operation time is noticeably reduced. Observe and record the run times of the rst few
operations (on a full charge). Use these run times as a reference point for comparison with run
times in the future.
- The battery must be removed from the pool vacuum before it is scrapped.
- The battery is to be disposed safely in accordance with local ordinances or regulations.
NOTE: Incorrect maintenance may reduce the battery life and aect its capacity as a result.
ENGLISH
11
Before detaching the damaged front wheels, you will need to detach the frame rst.
1) Pry and lift up the frame edge.
2) 3) 4) Rotate the frame to the other end.
5) Pick one end and lift it.
6) Lift the other end to detach the whole frame to replace the damaged wheel.
Front wheels replacement
11
2
2
33
4
4
55
66
ENGLISH
12
1. Use a pair of pliers to catch the hook at the end. Press on the hooks and push them inside the hole
of the hinge as shown. As the torsion spring will eject as it leaves the pin, be sure to cover the spring
with a piece of cloth as you pull the pin. Grasp the top round end of the pin with a pair of pliers.
Apply force to pull the pin completely out of the hinges.
2. There is a dot marking on one side of the connector, and it should be oriented downwards during
the subsequent assembly.
3. Insert the at end of the spring into the hole at the bottom of the post.
4. Use a nger to hold the spring underneath and align the hinges as shown. Ensure the round hook
end is placed underneath the bench as shown.
5. Align and insert the pin all the way through the spring hole and opposite hole.
Pole connector replacement
1 2
3
4
5
ENGLISH
13
BATTERY DISPOSAL (To be carried out by authorized technician)
Your pool vacuum is equipped with a maintenance-free rechargeable lithium-ion battery pack, which
must be disposed of properly. Recycling is required; please contact your local authority for more
information.
WARNING! Never attempt to disassemble a battery pack.
· Remove all personal items such as rings, bracelets, necklaces, and
watches when the battery pack is unwired from the pool vacuum.
· A battery can produce a short circuit current high enough to weld a
ring (or similar item) to metal, causing a severe burn in the process.
· Wear complete eye protection, gloves, and protective clothing when
the battery pack is being removed.
· Avoid touching the wires altogether and avoid contact between
them and any metal items, which could cause sparking and/or short
circuit the battery.
· Never smoke or allow a spark or ame in the vicinity of the battery or
the pool vacuum.
· Do not expose the battery to re or intense heat as this may result in
an explosion.
CAUTION!
If a battery leak occurs, avoid any contact with the leaking uids and place the damaged battery in a
plastic bag.
- If leaking uids come in contact with skin and clothing, wash immediately with plenty of soap and water.
- If leaking uids come in contact with eyes, do not rub them and immediately ush them with cool running
water for at least 15 minutes. Seek medical attention as soon as possible.
How to remove the battery pack (To be carried out by authorized technician)
Recommended tools (not included): Screwdriver.
WARNING! The pool vacuummust be disconnected from the supply
mains before removing the battery pack.
1) Place the pool vacuum on a at surface. Use the screwdriver to
unfasten the screws on the back cover. Remove the battery from the
chamber.
ENGLISH
14
2) To detach the battery connection wire, press on the clip of the
connector to pull it out. NOTE: Wrap the connector immediately
with insulating tape in order to avoid any short circuit caused by the
contact of both wire terminals.
Problem Possible Cause Solution
Cleaner does not start
working under water (after
5-10 seconds)
Stained water sensors
The stains can be removed by using a cotton bud soaked with juice of lemon
or vinegar to clean the areas around the water sensors.
Out of battery Charge the pool vacuum.
Does not capture the debris /
debris is leaked into the pool
Low battery Charge the pool vacuum.
Jammed impeller
Remove the pool vacuum from the water and turn the knob anticlockwise to
shut it o. Check and see if the impeller is jammed by large debris. Remove
the debris. If necessary, contact your dealer for further instructions.
WARNING! Make sure the pool vacuum is o before the unit is serviced.
Broken impeller Contact your dealer for replacement.
Filter bag is full / clogged Clean the lter bag.
Wheel detached from the
body.
Check if wheel/ wheel bracket
is broken
Replace a new wheel/wheel bracket.
Charging time is longer than
advertised
Stained charging pins
The stains can be removed by using a cotton bud soaked with juice of lemon
or vinegar to clean the areas around the charging pins.
Cleaner cannot be charged
Damaged battery
Contact dealer for battery replacement.
WARNING! DO NOT replace the battery by yourself. This could result
in severe or fatal injuries and the warranty will be voided as a result.
Charging plug is not correctly
connected to external adaptor
and pool vacuum
Refer to instruction manual and connect the charging accessories correctly.
External adaptor is out of order
Contact dealer for replacement.
WARNING! Using the wrong external adaptor will result in damaging
the pool vacuum / battery and voiding the warranty as a result.
Environmental Programmes, WEEE European Directive
Please respect the European Union regulations and help to protect the environment.
Return non-working electrical equipment to a facility appointed by your municipality that properly
recycles electrical and electronic equipment. Do not dispose them in unsorted waste bins. For items
containing removable batteries, remove batteries before disposing of the product.
All rights reserved. No part of this document may be reproduced or transmitted in any form or by
any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written
permission of Kokido Development Ltd. (L-23012005)
TROUBLESHOOTING
15
LIMITED WARRANTY
Warranty applies to the original owner only and cannot be transferred. Contact your local dealer for warranty. The
warranty does not cover:
· Normal wear and tear, including parts that might wear out over time (e.g., brush, rake, lter, lter bag, roller and
its accessories, etc.).
· Accidental damage.
· Damage due to inappropriate use against the rating plate and/or instructions provided in the Operating Manual
or other material.
· Damage caused by the lack of recommended maintenance.
· Damage from external sources such as transit, weather, electrical outages, or power surges.
· Failures caused by circumstances outside of recommendation (e.g., water temperature, storage temperature,
instruction of use and charging environment, etc.).
· Faults caused by:
- Negligent use, misuse, neglect, or careless operation of the appliance.
- Use of the appliance not in accordance with the Operating Manual.
- Use of parts not assembled or installed in accordance with the Operating Manual.
- Use of parts and accessories which are not Genuine Components.
- Faulty assembly or installation.
- Repairs or alterations (if allowed) carried out by unauthorized agents.
GB
We reserve the right to change all or part of the features of the articles or
contents of this document, without prior notice.
International patents pending
SAVE THESE INSTRUCTIONS
Support Email: [email protected]
Toll-Free Voicemail: (866) 683-7672
Download Instruction Manual & Videos:
QR Code:
https://shop.kokido.com/pages/support-xtrovac-910
Manufacturer: Kokido Development Limited. Unit 1319, Sunbeam Centre,
27 Shing Yip Street, Kwun Tong, Kowloon, HK
EV90BX/22R/AMZ/US Made in China
RoHS
We reserve the right to change all or part of the
features of the articles or contents of this document,
without prior notice.
International patents pending
