INSTRUCTIONS FOR:
MOTOR CYCLE LOCking gROUnD
AnCHOR - 4 SECURiTY BOLTS
MODEL No: MCgA02
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE inSTRUCTiOnS CAREFULLY. nOTE THE SAFE OPERATiOnAL REQUiREMEnTS, WARningS AnD
CAUTiOnS. USE THE PRODUCT CORRECTLY AnD WiTH CARE FOR THE PURPOSE FOR WHiCH iT iS inTEnDED. FAiLURE TO DO SO MAY
CAUSE DAMAgE AnD/OR PERSOnAL inJURY AnD WiLL inVALiDATE THE WARRAnTY. PLEASE kEEP inSTRUCTiOnS SAFE FOR FUTURE USE.
01284 757500
01284 703534
sales@sealey.co.uk
Sole Uk Distributor, Sealey group,
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
Web
1. SAFETY inSTRUCTiOnS
2. inTRODUCTiOn
3. inSTALLATiOn
4. USE
DO nOT install the Ground Anchor in a location where it is likely to cause a trip hazard.
Wear approved safety eye protection whilst drilling (standard spectacles are not adequate).
Keep children and unauthorised persons away from the working area whilst installing.
Heavy-duty hardened steel bolt-down anchor with key operated locking pin. Supplied with all xings. Provides a secure locking point for items such
as motorcycles, cycles, boats, caravans and trailers.
3.1. Locate the Ground Anchor on an area of sound concrete, where the unoccupied anchor will not present a trip hazard. (This unit is not
suitable for wall mounting).
3.2. Using the Ground Anchor as a template, mark the position of the required holes.
3.3. Use an 8mm masonry drill to drill pilot holes to a depth of 45mm.
3.4. Open the holes out using a 12mm masonry drill.
3.5. (See g.1.) Unscrew the bolt from the sleeve and, making sure that the threaded collar is located at the base, drive the sleeve and collar into
the prepared hole.
3.6. Once the sleeves/collars have been settled into all four holes, place the Ground Anchor over the sleeves.
3.7. Using a 6mm hex key, screw the bolts into the sleeves through the Ground Anchor base plate until light resistance is felt on all bolts.
3.8. Tighten all four bolts gradually, in a diagonal pattern, until tight and the Ground Anchor is rmly located.
3.9. To render the Ground Anchor tamper-proof, drive one of the ball bearings into each hex head with a hammer.
nOTE: The unit cannot be removed from the concrete once this has been completed.
g.1
4.1. Unlock the end cap and remove locking bar from the Ground Anchor.
4.2. Place the end links of a high tensile security chain in-between the locking lugs.
4.3. Slide the locking bar back through the locking lugs and chain links; resecure the locking cap as in g.2.
© Jack Sealey Limited
Original Language Version
MCGA02 ISSUE:1 06/11/13
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
iMPORTAnT: No liability is accepted for incorrect use of this product.
WARRAnTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
inFORMATiOn: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
g.2
