Lock
Unlock
See reverse side for more information
9/24
BC808
WARNING
Manual for Biometric Keypad Safe
Read all instructions before using this safe
- In Factory Default mode, the safe CANNOT be opened by
any fingerprint. For security purposes, please promptly
register your own fingerprint before starting to use the safe.
The initial Pin Code A: 1234 and Code B:123456. Kindly
follow the Fingerprint/Password Set Up to establish your
personalized fingerprint/password.
- Safe can be opened by either Fingerprint, Pin code, and /or
Emergency Keys.
- Test and Store emergency keys in a secure place, NOT
inside of the safe.
- Avoid leaving safe door open and unattended; it will allow
unauthorized individuals to add their fingerprints and/or
reprogram the safe, gaining full access to the safe and
the contents.
- To maximize the security and performance of the safe, test
registered fingerprints every 6 months.
- Test and make sure the safe works properly before
mounting. Once tested, mount the safe before use.
- Keep children away from safe; they should not play with or
around the safe at anytime. Children at play could
accidentally pull on the safe or accidentally pull on the safe
door causing safe to tip over if not properly mounted.
- Failure to follow these warnings could result in serious injury
or death.
OPENING SAFE WITH ACCESS KEY
1. To expose the key access, rotate the keypad
counter-clockwise smoothly to remove it from the door
2. Insert emergency key into key access and turn clockwise;
turn handle to unlocked position and open the safe.
Remove key and keep in a secure location.
B
A
A. Battery Compartment
B. Initialization Button
C. Handle
D. Fingerprint Scanner
C
E
F
PARTS OF THE SAFE
E. Keypad
F. External 9V Battery Source
G. Emergency Key Access
D
G
INSTALL BATTERIES
1. With the door open, remove the battery cover by sliding
the cover.
2. Insert 4 AA batteries by lining them up in a manner as
indicated by the “+” and “-“signs.
3. Put the arrow of the battery cover align to the arrow on the
compartment, slide the batteries cover back into place.
Restore the battery compartment cover.
NOTE:
DO NOT use any other type of non-alkaline battery.
DO NOT mix new and old batteries.
External Battery Source
9V battery can be used as an external power source. (9V
battery not included) Please remove the bottom black sticker
of keypad, then place 9V battery, touch the metal contacts
under the fingerprint or pin code mode. Safe should power
up, if not switch the polarity of the 9V battery.
LOCK/UNLOCK SAFE
Single Entry Mode
Unlock Safe with Pin Code
1. On the keypad enter registered pin code 4-8 digits and
press "#" to confirm. Green light flashes with 2
short beeps.
2. Turn the handle to unlock position to open the safe door.
Unlock Safe with Fingerprint
1. On the scanner place registered fingerprint, green light
flashes with 2 short beeps.
2. Turn the handle to unlock position to open the safe door.
Lock Safe
Close door and turn handle to lock position to lock the safe.
FINGERPRINT REGISTRATION
1. With the safe open, press and release initialization button
located inside of the safe. Yellow light flashes with 2
short beeps.
2. Immediately place desired finger on fingerprint scanner,
yellow light flashes with 2 short beeps. Remove the finger
from fingerprint scanner.
3. Repeat step 2 two more times, 1 long beep will be heard.
Fingerprint Registration is completed.
4. Fingerprint Registration can be stored up to 20
different fingerprints.
Important: 1 Fingerprint registration required 3 times of
placing the finger on the scanner to complete.
Successful Registration
1 long beep will be heard and yellow light will flash off.
Unsuccessful Registration
3 short beeps will be heard.
NOTE:
1. DO NOT choose a fingerprint with a scar or cut.
2. Make sure your hands are clean without dusts.
3. Make sure your finger is flatly placed at the center of
fingerprint scanner for better identification.
4. In cold or dry climate conditions, your hands may be too
dry, it will affect your fingerprint registration. We
recommend to moisturize your hands and rub your fingers
before registering.
5. Testing a fingerprint that is not registered to make sure the
safe cannot be unlocked to complete the
registration process.
6. Please follow the steps " LOCK/UNLOCK SAFE " to test
successful registration.
PIN CODES REGISTRATION
Default code A:1234 and Code B:123456
Pin Code can be 4-8 digits
Code A
1. With the safe open, press and release initialization button
located inside of the safe. Yellow light flashes with 2
short beeps.
2. On the keypad input new desired Pin Code and press
“ # ” to confirm. 2 short beeps will be heard, Pin Code
registration is completed.
Code B
1. With the safe open, Press “00” on keypad.
2. Press and release initialization button located inside of the
safe. Yellow light flashes with 3 short beeps.
3. On the keypad input new desired Pin Code and press “ # ”
to confirm. 2 short beeps will be heard, Pin Code
registration is completed.
Successful Registration
2 short beeps will be heard.
Important
1. Testing a pin code that is registered to make sure the safe
can be unlocked to complete the registration process.
2. Please follow the steps " LOCK/UNLOCK SAFE " to test
successful registration
©2024 BARSKA® | 855 Towne Center Drive | Pomona, CA 91767
RESET TO FACTORY DEFAULT MODE
Open the safe door and press initialization button for 5 seconds
and release, 1 long beep will be heard. The safe is back to factory
default mode. Initial Pin Code A:1234/ Code B:123456 ; ; ANY
fingerprint CANNOT open the safe.
The sound will be on as it is factory default condition.
Note: If you use Dual Entry Mode (Fingerprint and Pin Code)
before resetting. When you Reset Fingerprint Registration, the
safe entry will back to Single Entry Mode. Please refer to
“SWITCH BETWEEN SINGLE/DUAL ENTRY MODE " to change
the entry mode.
SWITCH BETWEEN SINGLE/DUAL ENTRY MODE
With safe open, press “ 1 “ on the keypad and press initialization
button at the same time. When you hear 1 long beep sound, the
Single/Dual Entry mode switch successfully.
Important: Dual Entry Mode require BOTH registered fingerprint
and pin code to unlock the safe.
UNLOCK SAFE ON DUAL ENTRY MODE
1. Place registered fingerprint on the scanner, green light flashes
with 2 short beeps.
2. Within 10 seconds, on the keypad enter pin code and press
"#" to confirm, green light flashes with 2 short beeps.
3. Turn the handle to unlock position to open the safe door.
LOCK OUT
Lock out mode is activated when enter wrong Registered Pin
Code 3 times or Fingerprint 5 times, the beep sound will last 20
seconds.
You can terminate the lock out mode by entering correct code or
fingerprint within the 20 Seconds lock out mode.
SOUND OFF/ ON
Press button " 00 ", Sound is disable. Press button " 66 ", the
sound is active.
Sound off: Lock out/motion sensor alarm is active, only the
keypad button and beep sound are disable.
LOW BATTERY WARNING
After entering correct pin code and red light is flashing or sound
warning this indicates the batteries are low.
Note: Safe may still be opened in low battery state depending on
battery voltage. If safe cannot be opened please use emergency
key or external battery source. All registered pin codes and
fingerprints remain stored.
MOTION SENSOR ALARM
You can press “ ” to active motion sensor alarm after
locking the safe, once the safe is unlocked, the motion
sensor alarm will be off.
If you wish to activate the motion sensor alarm, please press
“ ” each time after locking the safe.
The sound alarm will be on for 20 seconds if safe has any
motion when the motion sensor alarm is active.
You can terminate the alarm by entering correct pin code or
fingerprint within the 20 Seconds sound alarm.
If you use emergency key to stop the alarm sound, the
motion sensor alarm is still active.
Note: The motion sensor alarm is warning you unattended
action.
CARE AND MAINTENANCE
- To maximize the security and performance of the safe,
keep Fingerprint Scanner clean; use a dry cloth to remove
any smudges or prints off the Fingerprint Scanner after
each use.
- Test registered fingerprints and PIN code every 6 months.
- Keep liquids away from the control panel. Spills on the
control panel will cause damage and possibly
electric shock.
- Secure safe in a proper area to prevent from falling and
causing damage or injury.
- DO NOT disassemble the product. For all repairs, contact
BARSKA Customer Service.
- DO NOT use chemicals or cleaning agents to clean
the safe.
MOUNTING INSTRUCTIONS
The safe may be mounted to the floor. Be aware of the load
bearing. Failure to do so can result in personal injury and/or
damage to property. Use appropriate tools when performing
work and always use eye protection.
Floor Mounting
- Use proper drill tools depending on the type of floor you are
mounting the safe (wood, tile, or concrete).
- Measure the location of the pre-set drill holes; mark their
exact position onto the floor.
- Drill the appropriate size holes for the anchors you
are using.
- Carefully press the anchor into the holes at this time.
- Mount the safe by running screws from inside of the safe
and securing to anchors; ensure the safe is
mounted securely
Note: All information, feature, and specification displayed
herein are based on the data available at the time of
publishing, thus they are subject to change without notice.
All product pictures displayed herein are for illustration
purposes only. The actual product may vary due to
different circumstances
SAFE/LOCK BOX
1 YEAR LIMITED WARRANTY
BC767
BARSKA warrants this new safe/lock box to be free of defects
in material and/ or workmanship under normal use for a period
of twelve (12) months from the date product is purchased. This
limited warranty is delimited to repair or replacement only. This
warranty does not cover damage caused by improper
installation or maintenance. BARSKA disclaims all liability for
incidental or consequential damages resulting from misuse,
abuse, accident (such as dropping), fire, flood, service or
repairs other than those performed by BARSKA, acts of
nature, or arising out of any breach of this warranty. Altering
the product under any circumstances will automatically void
the warranty.
For service under this limited warranty, please have available
the proof of purchase and the purchase date and location as
well as a detailed description of the problem. This warranty is
not transferable and only applies to the original purchaser with
a proof of purchase from BARSKA or from an authorized
dealer. This warranty applies only to products purchased
within the United States, excluding Alaska, the Hawaiian
Islands and all U.S. territories in the Caribbean and the Pacific.
BARSKA will examine and go through troubleshooting
procedures, product repair or replacement of defective part(s)
or units with new part(s) or provide a new unit, if necessary,
during the warranty period. Reasonable shipping/handling
charges may apply and are based on Barska sole discretion.
Purchaser shall be required to prepay Shipping/handling
charges with a check or money order to BARSKA at time
product is returned. The Return Merchandise Authorization
Number (RMA#) and shipping/handling charge MUST be
obtained from BARSKA in advance of return. BARSKA shall
not be liable for damages or loss occurring during shipping.
Please visit via www.barska.com or call 909.445.8168 to
obtain the RMA#, Shipping/handling amount, and for more
information.
BARSKA reserves the right to modify or discontinue, without
prior notice to the purchaser, any model or style of the product.
BARSKA will determine, at its sole discretion, whether a
product will be repaired or replaced. BARSKA reserves the
right to discontinue or change any feature of its products at
any time. If an exact replacement or product is not available,
BARSKA reserves the right to provide a part or product that
matches as closely as possible.
LIMITATION OF REMEDIES
BARSKA disclaims any warranties, express or implied,
whether of merchantability or fitness for a particular use,
except as expressly set forth herein. The sole obligation of
BARSKA under this limited warranty shall be to repair or
replace the covered product, in accordance with the terms set
forth herein. BARSKA expressly disclaims any lost profits,
general, special, indirect or consequential damages which
may result from breach of any warranty, or arising out of the
use or inability to use any BARSKA product. Any warranties
which are implied and which cannot be disclaimed shall be
limited in duration to a term of one year from the date of
original retail purchase.
Some states do not allow the exclusion or limitation of
incidental or consequential damages or limitation on how long
an implied warranty lasts, so the above limitations and
exclusions may not apply to you.
BARSKA
855 Towne Center Drive, Pomona, CA 91767
