Popsicle
Machine
Operation
Manual
Dear customer:
Thank you for choosing our popsicle machine, hope
this machine suits your need. Before operation, please read
the instruction manual thoroughly. Also please keep your
instructions for further purpose.
Contents
I. Usage of machine ………………………………. 1
II. Technical data ………………………………….. 1
III. Installation …………………………………….. 2
IV. How to use ………………………………. .……3
V. Precautions ………………………………………4
VI. Troubleshooting ……………………………….. 4
VII. Packing list …………………………………….5
I. Usage of our machine
Our popsicle machine, the appearance of fine, safe and
reliable. Stainless steel shell, luxurious and easy to clean. With
high-quality compressor and microcomputer controller, the
machine is mainly used for making popsicles, widely used in
cold drinks chain stores, bars, restaurants and other
entertainment.
II. Technical data (see rating label on machine)
III. Installation
1) According to the packing list, check parts kit and the
whole machine.
2) Place the machine in a ventilated and dry location to
ensure that the wind gates on each side of the machine
are at a distance of 500mm above the wall cargo
barrier.
3) Connect the power supply with reliable grounding as
required on machine’s rating label.
4) Put the calcium chloride solution as refrigerant into the
machine tank.
Refrigerant formulation:
Model BBJ-1A BBJ-2A
Solution
temperature
Solution amount and temperature 23.5kg 50kg -28℃
Calcium
chloride
Water proportion（74
%
） 17.4kg 37kg
-31℃
Calcium chloride proportion
（26
%
）
6.1kg 13kg
Calcium
chloride
Water proportion（77
%
） 18.1kg 38.5kg
-21℃
Calcium chloride proportion
（23
%
）
5.4kg 11.5kg
Please noted：
① The solution concentration may be reduced with long
time use, the way is to add calcium chloride material,
but pay attention: the optimal proportion of water and
calcium chloride is 1.24, the Baume degree is 28.0;
② Try not to use sodium chloride solution, which cannot
meet the requirements of the machine use and achieve
the best cooling effect.
③ The configured solution should be placed in the
normal environment for 24h. When the solution is fully
dissolved and reach the same temperature as the room,
it is better to use a filter to remove the inside precipitate.
5) Microcomputer controller setting：
Item Data Note
Maximum temperature
setting
-22℃ Starting up temperature
Minimum temperature
setting
-25℃ Shutdown temperature
Compressor delay start
time
3min
The compressor will
delay refrigeration when
turn on the machine
Note: These parameters have been set before leaving the factory,
please do not change.
IV. How to use
1. Clean up：Before making popsicle, use water to clean
the popsicle module.
2. Prepare the popsicle material
a) In order to make your popsicle flavor better, taste
better, it is recommended to use ice lolly power or
slurry and follow the instructions on the packing bag
to adjust.
b) Here to recommend a common economic popsicle
formula:
Material
Milk
powder
White
sugar
Water Others
Mass ratio 1 1 10
Appropriate
amount
3. Operation
a) Plug in，then turn on the power switch to the”
一”position，the pump motor in tank starts to work；
Microcomputer controller will show current
temperature and LED will flash. After 3 mins, the
compressor starts working and the temperature in
cooling tank will reach -18℃；The machine will restart
when the temperature gets higher.
b) Put the slurry into the popsicle module (slurry should
not be over the 3/4 line), and add the sticks to the draft
device. Then put the popsicle module to the freezing
cylinder, cover the lid, let the machine work 20-40
mins.
c) After the popsicles are ready, remove the entire
popsicle module and immerse it in the water for 2-5
mins; Remove the draft device, take out the popsicles.
V. Precautions
1) During moving machine, the inclination does not allow
more than 45 degrees.。
2) Power supply voltage requirements of the rated voltage,
there must be a reliable grounding; No sharing the
same socket with other electrical appliances.
3) Out of the wind side should be enough to stay more
than 500mm space to ensure that the machine heat.
4) When the machine is covered with a lid, avoid pushing
the hand into the bucket.
5) The machine should be unplugged after each use of
power; after washing with a towel dry, the appearance
can be wiped with a wet towel, also should not be
washed directly with water.
VI. Troubleshooting
Problem Possible cause Solution
Machine
no work
1.Power or voltage unstable 1.Voltage stabilizer
2.No electricity connected 2.Re-plug in
Frequently
shut down
1. Power or voltage unstable 1. Voltage stabilizer
2.Wind gates blocked 2.500mm at least to wind
gates
3.Enviromental temp too hot 3.Change location of machine
4.Compressor capacity
damaged
4.Replace capacity
Too noisy
1.Machine on a bumpy
surface
1.Place machine on a flat
surface
2.Parts on machine loosen 2.Adjust parts and tighten
them
VII. Packing list
No. Item BBJ-1A BBJ-2A
1 Popsicle machine 1set 1set
2 Popsicle Mold 1set 2 sets
3 Sticker holder 1pc 2 pcs
4 Operation Manual 1pc 1pc
5 QC pass 1pc
1pc
