BAUMR-AG SAWWCSBMRA6X4 Wall Chaser Dual Handles and Wet User Manual

Model shown is BM-WC52

User Manual

[Revision 6.0 November 2023]

READ THIS MANUAL CAREFULLY BEFORE USE – FAILURE TO DO SO MAY RESULT IN INJURY, PROPERTY DAMAGE AND

MAY VOID WARRANTY. • KEEP THIS MANUAL FOR FUTURE REFERENCE. • Products covered by this manual may vary in

appearance, assembly, inclusions, specifications, description, and packaging.

Wall Chasers - BM-WC52, BM-WC54, BM-WC64

Safety

Safety messages are designed to alert you to possible dangers or hazards that could cause death, injury or

equipment or property damage if not understood or followed. Safety messages have the following symbols:

You WILL be KILLED or

SERIOUSLY INJURED if you do

not follow instructions.

You CAN be KILLED or

SERIOUSLY INJURED if you do

not follow instructions.

You CAN be INJURED if you do

not follow instructions or equipment

damage may occur.

It is vital that you read and understand this

user manual before using the product,

including safety warnings, and any assembly

and operating instructions. Keep the manual

for future reference.

Safety precautions and recommendations

detailed here must be fully understood and

followed to reduce the risk of injury, fire,

explosion, electrical hazard, and/or property

damage.

Safety information presented here is generic

in nature – some advice may not be

applicable to every product. The term

"equipment" refers to the product, be it

electrical mains powered, battery powered or

combustion engine powered.

• Before Use - If you are not familiar with the

safe operation/handling of the equipment or

are in any way unsure of any aspect of

suitability or correct use for your

application, you should complete training

conducted by a person or organization

qualified in safe use and operation of this

equipment, including fuel/electrical handling

and safety.

• Do NOT operate the equipment in

flammable or explosive environments, such

as in the presence of flammable liquids,

gases, or dust. The equipment may create

sparks or heat that may ignite flammable

substances.

• Keep clear of moving parts.

• Equipment may be a potential source of

electric shock or injury if misused.

• Do NOT operate the equipment if it is

damaged, malfunctioning or is in an

excessively worn state.

• Do NOT allow others to use the equipment

unless they have read this manual and are

adequately trained.

• Keep packaging away from children - risk

of suffocation! Operators must use the

equipment correctly. When using the

equipment, consider conditions and pay

due care to persons and property.

General Work Area Safety

• Work areas should be clean and well it.

• Do not operate the equipment if

bystanders, animals etc are within

operating range of the equipment or the

general work area.

• If devices are provided for connecting dust

extraction / collection facilities, ensure

these are connected and used properly.

Dust collection can reduce dust-related

hazards.

General Personal Safety

• Wear appropriate protective equipment

when operating, servicing, or when in the

operating area of the equipment to help

protect from eye and ear injury, poisoning,

burns, cutting and crush injuries. Protective

equipment such as safety goggles,

respirators, non-slip safety footwear, hard

hat, hearing protection etc should be used

for appropriate equipment / conditions.

Other people nearby should also wear

appropriate personal protective equipment.

Do not wear loose clothing or jewellery,

which can be caught in moving parts. Keep

hair and clothing away from the equipment.

• Stay alert and use common sense when

operating the equipment. Do not over-

reach. Always maintain secure footing and

balance.

• Do not use the equipment if tired or under

the influence of drugs, alcohol, or

medication.

• This equipment is not intended for use by

persons with reduced physical, sensory, or

mental capabilities.

General Fuel Safety

• Petrol/fuel/gasoline is extremely flammable

– keep clear of naked flames or other

ignition sources.

• Do not spill fuel. If you spill fuel, wipe it off

the equipment immediately – if fuel gets on

your clothing, change clothing.

• Do NOT smoke near fuel or when

refuelling.

• Always shut off the engine before

refuelling.

• Do NOT refuel a hot engine.

• Open the fuel cap carefully to allow any

pressure build-up in the tank to release

slowly.

• Always refuel in well ventilated areas.

• Always check for fuel leakage. If fuel

leakage is found, do not start, or run the

engine until all leaks are fixed.

General Carbon-Monoxide Safety

• Using a combustion engine indoors CAN

KILL IN MINUTES. Engine exhaust

contains carbon-monoxide – a poison you

cannot smell or see.

• Use combustion engines OUTSIDE only,

and far away from windows, doors, and

vents.

General Equipment Use and Care

• The equipment is designed for domestic

use only.

• Handle the equipment safely and carefully.

• Before use, inspect the equipment for

misalignment or binding of moving parts,

loose components, damage, or any other

condition that may affect its operation. If

damaged, have the equipment repaired by

an authorised service centre or technician

before use.

• Prevent unintentional starting of the

equipment - ensure equipment and power

switches are in the OFF position before

connecting or moving equipment. Do not

carry equipment with hands or fingers

touching any controls. Remove any tools or

other items that are not a part of the

equipment from it before starting or

switching on.

• Do not force the equipment. Use the

correct equipment for your application.

Equipment will perform better and be safer

when used within its design and usage

parameters.

• Use the equipment and accessories etc. in

accordance with these instructions,

considering working conditions and the

work to be performed. Using the equipment

for operations different from those intended

could result in hazardous situations.

• Always keep equipment components

(engines, hoses, handles, controls, frames,

housings, guards etc) and accessories

(cutting tools, nozzles, bits etc) properly

maintained. Keep the equipment clean and,

where applicable, properly lubricated.

• Store the equipment out of reach of

children or untrained persons. To avoid

burns or fire hazards, let the equipment

cool completely before transporting or

storing. Never place or store the equipment

near flammable materials, combustible

gases, or liquids etc.

• The equipment is not weather-proof, and

should not be stored in direct sunlight, at

high ambient temperatures or locations that

are damp or humid.

• Do not clean equipment with solvents,

flammable liquids, or harsh abrasives.

• For specific equipment safety use and care,

see Equipment Safety.

Wall Chasers - BM-WC52, BM-WC54, BM-WC64

General Electrical Safety

• Inspect electrical equipment, extension

cords, power bars, and electrical fittings for

damage or wear before each use. Repair or

replace damaged equipment immediately.

• Ensure all power sources conform to

equipment voltage requirements and are

disconnected before connecting or

disconnecting equipment.

• When wiring electrically powered

equipment, follow all electrical and safety

codes.

• Always use a Residual Current Device

(RCD) (GFCI) / Earth Leakage Circuit

Breaker / Safety Switch when operating this

item (electrical items only).

• High voltage / high current power lines may

be present. Use extreme caution to avoid

contact or interference with power lines.

Electrical shock can be fatal.

General Electrical Safety

• Electrically grounded equipment must have

an approved cord and plug and be

connected to a grounded electrical outlet.

• Do NOT bypass the ON/OFF switch and

operate equipment by connecting and

disconnecting the electrical cord.

• Do NOT use equipment that has exposed

wiring, damaged switches, covers or

guards.

• Do NOT use electrical equipment in wet

conditions or in damp locations.

• Do NOT use electrical cords to lift, move or

carry equipment.

• Do NOT coil or knot electrical cords, and

ensure electrical cords are not trip hazards.

General Service Information

• The equipment must be serviced or

repaired at authorised service centres by

qualified personnel only.

• Replacement parts must be original

equipment manufacturer (OEM) to ensure

equipment safety is maintained.

• Do NOT attempt any maintenance or repair

work not described in this manual.

• After use, the equipment and components

may still be hot – allow the equipment to

cool and disconnect spark plugs and/or

electrical power sources and/or batteries

from it before adjusting, changing

accessories, or performing repair or

maintenance.

• Do NOT adjust while the equipment is

running.

• Perform service-related activities in suitable

conditions, such as a workshop.

• Replace worn, damaged or missing

warning/safety labels immediately.

Wall Chaser Safety

• Avoid grooving near live cables, gas pipelines, and water pipes.

• Wear safety equipment such as protective glasses and dust mask while working on the wall chaser.

• Avoid burns! DO NOT touch the wall chaser’s head (clamp, saw blade and output shaft) while operating it.

• Prevent water from entering the motor. DO NOT let water get into the motor to avoid electric shock risks.

• Maintain the tool regularly. Clean up the earth plug promptly after each use.

• DO NOT lift the machine directly with its cable to avoid damaging the tool and short-circuiting.

• Use only in suitable work environments, away from wet/damp and dangerous conditions.

• Be careful not to step on the wire or pull the plug with the wire.

• Always unplug the tool first before performing any sort of maintenance on it.

Wall Chasers - BM-WC52, BM-WC54, BM-WC64

Safety Symbols

The product may have safety warning labels attached to it, explained below. Understand the symbols on your

product and their meanings. If any stickers become unreadable, unattached etc., replace them.

Flammable Material Hazard

Flammable liquids, gases, or

substances etc may present.

Avoid ignition sources and open

flames. Danger of fire.

Read User Manual

Read and fully understand

product safety warnings,

operation, procedures etc before

using the product.

Use Hand Protection

Wear appropriate hand protection

and take due care as the product

or use of the product may present

hand hazards.

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be fatal.

Electrocution / Electrical Shock

Hazard

High voltage or high current

electricity may be present or

required by the product. Take

due care when handling electrical

products, cables, plugs and

leads. Electrical shock can be

fatal.

Toxic Fumes / Dust Hazard

Using the product or by-products

from use may produce fumes,

smoke or particles that could be

harmful if inhaled. Wear

appropriate breathing protection

and have adequate ventilation.

Explosive Material Hazard

Combustible liquids, gases, or

substances etc may be present.

Avoid ignition sources and open

flames. Danger of explosion.

Cutting / Amputation Hazard

The product may have blades,

edges or mechanical devices that

can cause severe cut injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Crush Hazard

The product may have blades,

edges or mechanical devices that

can cause severe crush injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Single Operator Only

The product must be operated by

a single person only. More than

one person operating the product

may introduce additional hazards.

Use Face Protection

Wear appropriate full-face

protection and take due care as

the product or use of the product

may present face and eye

hazards.

Use Foot Protection

Wear appropriate foot protection

and take due care as the product

or use of the product may present

foot hazards.

Use Eye / Ear / Head Protection

Wear appropriate eye and / or

ear and / or head protection and

take due care as the product or

use of the product may present

eye, hearing, and head hazards.

Running Hazard

Do not run on or near the product

as doing so may present a fall

hazard.

Diving Hazard

Do not dive into the product as

doing so may present a neck /

head injury hazard.

Adult Supervision Required

Always supervise children and

other users of a product to

prevent drowning or injury.

Skin Penetration / Puncture

Hazard

The product may produce

pressure, emit liquids or objects

that can cause severe injury to

fingers, limbs, blood etc. Take

due care when handling and

using the product.

Hot Surface Hazard

Be aware that the product may

produce high temperatures and

hot surfaces that can cause burn

injuries.

Flying Debris Hazard

Be aware that the product or use

of the product may present

hazards produced by flying

debris. Wear appropriate clothing

and protective devices.

Moving Parts Hazard

Be aware that the product

contains or uses mechanical

devices that move or rotate.

Always wait for moving parts to

stop fully before handling the

product, adjusting, maintenance

etc.

Wall Chasers - BM-WC52, BM-WC54, BM-WC64

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be fatal.

Pull Hazard

Be aware that the product

contains or uses mechanical

devices that can pull in objects

and can cause severe injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Slope / Fall Injury Hazard

Be aware that using the product

on sloping surfaces or in slippery

conditions may present additional

dangers from falls and contact

with blades, moving parts, hot

surfaces etc.

"Slam Dunk" Warning

Do NOT attempt "slam dunk"

manoeuvres as this may result in

severe injury due to falling,

product breakage or collapse etc.

Electrocution / Electrical Shock

Hazard - Outdoor

High voltage or high current

electricity may be present or

required by the product. Do NOT

use in rain, damp, or wet

conditions. Electrical shock can

be fatal.

Electrocution / Electrical Shock

Hazard - Disconnect

High voltage or high current

electricity may be present or

required by the product. Always

disconnect the product from the

electrical supply before handling

the product, adjusting,

maintenance etc.

Power Line Electrocution

Hazard

High voltage / high current power

lines may be present. Use

extreme caution to avoid contact

or interference with power lines.

Electrical shock can be fatal.

"Kick-Back" Hazard

High level of "kick-back" hazard

that can cause the machine to

suddenly rotate towards operator.

Kick-back injury can be fatal.

Winch Operator Position

Hazard

Do NOT stand between winch

and load. Do NOT use winch to

move people.

Winch Lift Hazard

Do NOT LIFT load vertically. Use

machine to PULL only.

Cable Hazard

Ensure that load bearing cable is

not kinked or knotted.

Winch Cable Hazard

Ensure that there is a minimum

number of cable coils on

winching mechanism.

Winch Hook Hazard

Carry hook to load – do NOT

throw or run.

Flash / Blinding Hazard

Wear appropriate eye protection

for welding. Direct exposure to

weld arcs may cause permanent

eye injury.

Laser Hazard

Laser may be in use – do NOT

look directly at laser or allow

others to.

Wall Chasers - BM-WC52, BM-WC54, BM-WC64

Table of Contents

Safety ............................................................................................................................................................. 2

Safety Symbols ........................................................................................................................................................... 4

Assembly ....................................................................................................................................................... 7

Installing the Rollers ................................................................................................................................................... 7

Installing the Side Handle ........................................................................................................................................... 7

Installing a Saw Blade ................................................................................................................................................ 7

Installing the Water Pump or Vacuum Cleaner .......................................................................................................... 8

Using the Vacuum ...................................................................................................................................................... 9

Spare Parts .................................................................................................................................................. 10

Operation ..................................................................................................................................................... 11

Features .................................................................................................................................................................... 11

Rotating the Handle .................................................................................................................................................. 12

Maintenance ................................................................................................................................................ 13

Replacing the Carbon Brush .................................................................................................................................... 13

Cleaning Dirt from the Tool After Each Use ............................................................................................................. 14

Specifications ............................................................................................................................................. 15

BM-WC52 ................................................................................................................................................................. 15

BM-WC54 ................................................................................................................................................................. 16

BM-WC64 ................................................................................................................................................................. 17

Product Name

Assembly

Installing the Rollers

The rollers are a necessary device for continuous grooving when turning corners. Place it on the position set on

the movable cover and tighten the two screws with a cross screwdriver, as shown in the figure below:

Installing the Side Handle

Place the position of the side handle bayonet into the bulge on the top of the head shell, secure the flat mat with

an M8 screw. Tighten the screw with a hexagon wrench, as shown in the figure.

After working, clear up any silt and dirt on the tool to prevent rust from forming, or turn off the faucet. Remove

the packaging handle fist before starting the tool, otherwise it is easy to cause harm.

Installing a Saw Blade

1. Loosen the screw under the protective cover, remove the screw on the protective cover, and tum the

protective cover to the side cover; also, remove the three side-cover screws and remove all the side-cover.

2. Press the self-locking button, rotate the movable cover to the highest position, remove the upper pressure

plate with the wrench, install the saw blade to the convex platform corresponding to the lower pressure plate,

and then install the corresponding number of lower pressure plate/middle pressure plate and saw blade,

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Wall Chasers - BM-WC52, BM-WC54, BM-WC64

then install the upper pressure plate, and screw down the upper pressure plate with the spanner while

pressing the self-locking button.

3. Install the protective cover and tighten the rubber head hand screw on the protective cover, also install all

the side-cover.

Installing the Water Pump or Vacuum Cleaner

1. Install a water pump to remove dust: connect the water pipe with a ø5 inner hole to the tap (optional

accessories).

2. Connect one end of the transparent hose to the tap, through the pipe hole on the water retaining cover, and

the other end to the pump, and put the pump head down (the blade down) into the water container.

3. Tum ON the water pump switch and adjust the tap screw to your desired water flow strength.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Wall Chasers - BM-WC52, BM-WC54, BM-WC64

Using the Vacuum

1. After installing the vacuum cleaner, remove the water retaining cap screw in the vacuuming joint with a cross

screwdriver and remove the water retaining cap. The water retaining cap can be pulled out with a long nose

pliers, or it can be pushed out from the saw blade cavity with a screwdriver.

2. Screw in the dust suction hose with a diameter of ø32mm directly into the vacuuming joint (optional

accessories).

3. The alignment slot on the alignment plate is the starting position of the saw blade, and the marking line is

aligned with it or with the laser line.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Wall Chasers - BM-WC52, BM-WC54, BM-WC64

Spare Parts

Spare parts available for purchase, scan QR codes below:

QR Code SKU QR Code SKU

SAWWCSBMRA5X2

SAWWCSBMRA5X4

SAWWCSBMRA6X4

SAWWCSBMRAVC5

SAWWCSBMRAVC5-

5X2

SAWWCSBMRAVC5-

5X4

SAWWCSBMRAVC5-

6X4

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Wall Chasers - BM-WC52, BM-WC54, BM-WC64

Operation

Features

The tool has a rotating device for moving the cover. When passing a corner, the tool can continuously open the

slot without stopping.

The rear cover can rotate around 90° to adapt to cutting different directions. It can also be used as a cutting and

polishing tool.

The cutting direction of the tool is a push-type cutting.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Wall Chasers - BM-WC52, BM-WC54, BM-WC64

Rotating the Handle

Hold in the button as shown, while turning the handle.

NOTE: Rotating handle not equipped with all models.

90°

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Wall Chasers - BM-WC52, BM-WC54, BM-WC64

Maintenance

Replacing the Carbon Brush

NOTE: The carbon brush must be checked and replaced regularly. Generally, the normal use of one pair

of carbon brush is 200 hours, but the specific time is different according to the difference in tool, work

environment and cutting material. Normally, in normal use, the brushes on both sides need to be replaced at the

same time. Please use only the brushes of the same kind of material. The brushes need to be changed in a

timely manner when its length is less than 5mm, otherwise it will easily damage the tool.

WARNING! Turn off the power of the tool and pull out the plug, or you will be electrocuted! The brush

must be replaced immediately if there is a large spark due to the carbon brush wearing off! Use only

original carbon brush from the supplier or an authorised service centre, otherwise it can damage the

motor!

1. Loosen the carbon brush cover on the tool casing with a cross screwdriver, then use long nose pliers to lift

the coil spring up and take out the carbon brush.

2. Testing the assembly of a new carbon brush: Keep the brush clean and make it move freely in the brush

holder. If there isn't any stagnation in the clamping action, then install directly. Then, loosen the coil spring

and press it against the groove at the end of the brush tail, and then press the brush cover and tighten it.

3. Testing the tool: Start the tool for 15 minutes to observe whether the spark of the tool is good, if not, the

brush needs to be re-installed again.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Wall Chasers - BM-WC52, BM-WC54, BM-WC64

Cleaning Dirt from the Tool After Each Use

•

Cleaning with a water pump: Continue to boot for a minute after you finish cutting to let the water clean the

inner cavity of the saw blade, including any dirt left on the saw blade cavity, in the dust removing port and in

the dust outlet. Boot to clean after manual cleaning and then dry naturally. Otherwise, the mud will become

dry and become stuck and rusted, and the tap will be blocked. When using external high-pressure water to

clean, note that the inlet and outlet where the water passes through should not be used.

•

Cleaning with a vacuum cleaner: Continue to boot for a minute after you finish cutting, and then manually

clean the inner cavity of the saw blade, the dust removing port and the dust outlet. And then boot for a

minute again to clean up the tool, preventing jams, formation of rust and the tap getting blocked.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Wall Chasers - BM-WC52, BM-WC54, BM-WC64

Specifications

BM-WC52

Application

Grooving and cutting

Voltage

220-240v / 50hz

Plug

SAA

Cable length (m)

2.5m (whole length)

Power

1550W

Speed

7900rpm

Cutting width

30mm, adjust with spacer and number of blades

Cutting depth

41mm, not adjustable

Size of saw blade

129x22.23x4.5mm

Type of saw blade

Diamond

Material of saw blade

Diamond

Material that could be cut

Solid bricks, honeycomb bricks, sand and stone

concrete, polished bricks, tiles (replace with different

saw blades as needed, suitable for cutting different

materials)

Saw blade max. quantity

5 (but only comes with 4 blades by default)

Continuous carver cutting without stop/can

groove the wall in 90 degree

Yes

Mechanical alignment function

Yes

Laser alignment function

No

Light

No

Excellent dust and water resistance, basically

achieving dust-free operation

Yes

Soft rubber cover to protect your hand from dirt

and danger, protect the tool from water

Yes

The handle can rotate 90 degrees to facilitate

horizontal and vertical slotting

Yes, left-handed 90 degree, positive, right handed 90

degree

2 ways to remove dust, connect the water pump

or vacuum cleaner

Yes

Size of dust suction hose

32mm diameter

Overload protection

No

Overheat protection

No

Indication light for warning

No

Safety function

The cover of head will protect the user

Brush on base

No

Base roller

No

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Wall Chasers - BM-WC52, BM-WC54, BM-WC64

BM-WC54

Application

Grooving and cutting

Voltage

220v - 240v/50hz

Plug

SAA

Cable length (m)

2.5m (whole length)

Power

1550W

Speed

7900rpm

Cutting width

30mm, adjust with a spacer and number of blades

Cutting depth

41mm, not adjustable

Size of saw blade

129x22.23x4.5mm

Type of saw blade

Diamond

Material of saw blade

Diamond

Material that could be cut

Solid bricks, honeycomb bricks, sand and stone concrete,

polishes bricks, tiles (replace with different saw blades as

needed, suitable for cutting different materials)

Saw blade max. quantity

5 (but only comes with 4 blades by default)

Continuous carver cutting without stop/can

groove the wall in 90 degree

Yes

Mechanical alignment function

Yes

Laser alignment function

No

Light

No

Excellent dust and water resistance, basically

achieving dust-free operation

Yes

Soft rubber cover to protect your hand from dirt

and danger, protect the tool from water

No

The handle can rotate 90 degrees to facilitate

horizontal and vertical slotting

No

2 ways to remove dust, connect the water pump

or vacuum cleaner

Yes

Size of dust suction hose

32mm diameter

Overload protection

No

Overheat protection

No

Indication light for warning

No

Safety function

The cover of head will protect the user

Brush on base

No

Base roller

No

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Wall Chasers - BM-WC52, BM-WC54, BM-WC64

BM-WC64

Application

Grooving and cutting

Voltage

220v - 240v/50hz

Plug

SAA

Cable length (m)

3.5m (whole length)

Power

1850W

Speed

6500rpm

Cutting width

44mm, adjust with a spacer and number of blades

Cutting depth

44mm, can be adjustable with a screw

Size of saw blade

129x22.23x4.5mm

Type of saw blade

Diamond

Material of saw blade

Diamond

Material that could be cut

Solid bricks, honeycomb bricks, sand and stone

concrete, polishes bricks, tiles (replace with different

saw blades as needed, suitable for cutting different

materials)

Saw blade max. quantity

8 (but only comes with 4 blades by default)

Continuous carver cutting without stop/can

groove the wall in 90 degree

Yes

Mechanical alignment function

Yes

Laser alignment function

No

Light

No

Excellent dust and water resistance, basically

achieving dust-free operation

Yes

Soft rubber cover to protect your hand from dirt

and danger, protect the tool from water

No

The handle can rotate 90 degrees to facilitate

horizontal and vertical slotting

Yes, left-handed 90 degree, positive, right-handed 90

degree, press the black button on the handle to adjust

the angle

2 ways to remove dust, connect the water pump

or vacuum cleaner

Yes

Size of dust suction hose

32mm diameter

Overload protection

No

Overheat protection

No

Indication light for warning

No

Safety function

The cover of head will protect the user

Brush on base

No

Base roller

Yes

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Some experts believe that the incorrect or prolonged use of almost any

product may cause serious injury or death. To help reduce your risk of

serious injury or death, refer to the information below. For more information,

see www.datastreamserver.com/safety



Consult all documentation, packaging,

and product labelling before use. Note

that some products feature

documentation available online. It is

recommended to print and retain the

documentation.



Before each use, check the product for

loose/broken/damaged/missing parts,

wear, or leaks (if applicable). Never use a

product with

loose/broken/damaged/missing parts,

wear, or leaks.



Products must be inspected and serviced

(if applicable) by a qualified technician

every 6 months. This is based on

average residential use by persons of

average size and strength, and on a

property of average metropolitan size.

Use beyond these recommendations may

require more frequent

inspections/servicing.



Ensure that all users of the product have

completed a suitable industry recognised

training course before being allowed

access to the product.



The product has been supplied by a general merchandise

retailer that may not be familiar with your specific

application or description of application. Be sure to attain

third-party approval from a qualified specialist for your

application before use, regardless of any assurances from

the retailer or its representatives.



This product is not intended for use where fail-safe

operation is required. As with any product (for example,

automobile, computer, toaster), there is the possibility of

technical issues that may require the repair or

replacement of parts, or the product itself. If the possibility

of such failure and the associated time it may take to

rectify could in any way inconvenience the user, business,

or employee, or financially affect the user, business, or

employee, then the product is not suitable for your

requirements. This product is not intended for use where

incorrect operation or a failure of any kind, including but

not limited to, a condition requiring product return,

replacement, parts replacement, or service by a

technician may cause financial loss, loss of employee

time or an inconvenience requiring compensation.



If this product has been purchased in error when

considering the information presented here, contact the

retailer directly for details of their returns policy, if

required.

ideas, diagrams, or images may be reproduced or transmitted in any form or by any means, electronic or

mechanical, including photocopying, scanning, or recording, or any information storage and retrieval system,

without express permission or consent from the publisher.

BAUMR-AG SAWWCSBMRA6X4 Wall Chaser Dual Handles and Wet Cutting System for Enhanced Precision and Flexibility

Product's Documents

Product manual

Specifications

BAUMR-AG SAWWCSBMRA6X4 Questions and Answers