Loading ...
Loading ...
Loading ...
4
To install the dust box:
1. Slide the dust box into the body of the
HAMMERVAC™.
2. The dust box latches should snap into place.
NOTE: Do not operate the HAMMERVAC™ without
the dust box and HEPA lter in place. Dust box cannot
be installed without HEPA lter.
CAUTION
Keep filter clean.
Efficiency of the
HAMMERVAC™ is largely dependent on the lter.
A dirty lter will reduce the air ow and overall
eciency of the system. Do not clean with water
or compressed air. Remove from dust box and
tap clean.
Installing/Removing Nozzle
Replace the nozzle:
• After drilling about 1500 holes,
• When the bit brush shows signs
of wear,
• When suction is reduced,
• When dust escapes through the
bit brush during use
To replace the Standard
(Cat. No. 14-52-0105 and Large
Cat. No. 14-52-0110) nozzles,
rotate the nozzle release lever
down to the open position and
pull out nozzle from the lower nozzle assembly.
Slide the new nozzle into the lower nozzle assembly
and rotate the nozzle release lever up to the closed
position.
Rear depth
bracket
screws
Rear depth
bracket
Tabs
Dove
tail
slot
Front depth
bracket
Bit depth
gauge button
Removing/Installing the Depth Stop
To remove the depth stop:
1. Turn OFF the tool.
2. Remove the battery pack.
3. Remove screws from left and right side of rear
depth bracket with a philips screwdriver.
4. Remove front depth bracket by pulling up on it.
NOTE: Use a at head screwdriver to free the
snap, if needed.
To install the depth stop:
1. Place the rear depth bracket into the slot on the
top of the dedicated dust extractor.
2. Insert screws into the left and right side of rear
depth bracket with a philips screwdriver.
3. Insert front depth bracket into dove tail slot on
nozzle base and push down until snapped into
place.
SYMBOLOGY
Volts
Direct Current
Read Operator's Manual
SPECIFICATIONS
Cat. No. .................................................... 2912-DE
For use only with 2912-20 & 2914-20
M18 FUEL™ 1" SDS PLUS Rotary Hammers
Cat. No. .................................................... 2915-DE
For use only with 2915-20 M18 FUEL™
1-1/8" SDS PLUS Rotary Hammer
Small Nozzle Max Diameter ............................. 5/8"
Large Nozzle Max Diameter .......................... 1-1/8"
Recommended Ambient
Operating Temperature ......................0°F to 125°F
Dust Box Cat. No ................................ 49-90-2344
ASSEMBLY
WARNING
Only use accessories
specifically recom-
mended for this tool. Others may be hazardous.
To reduce the risk of injury, always remove the
battery pack before removing the dust box. Do
not use tool without dust box and HEPA lter
in place.
Removing/Installing the Dust Box
and HEPA Filter
To remove the dust box:
1. Turn OFF the tool.
2. Remove the battery pack.
3. Squeeze the dust box latches.
4. Pull the dust box away from the HAMMERVAC™.
5. Empty debris by holding away
Dust box
port
HEPA
lter
from the user’s face and tap-
ping dust box into a trash can,
pail, or other reasonable
container. For best cleaning
results, connect a vacuum
hose with dust extraction
adapter (Cat. No. 49-90-1959)
to the dust box port and suc-
tion out debris.
6. If necessary, pull the HEPA lter away from the
dust box and tap clean. Do not clean with water
or compressed air. After about 1500 holes or loss
of suction, discard and replace HEPA lter (Cat.
No. 49-90-2306).
Loading ...
Loading ...
Loading ...