Loading ...
Loading ...
Loading ...
20
Electricity
In the use of the product, you must be in strict compliance with
the electrical safety regulations of the nation and region. The
equipment shall not be exposed to dripping or splashing and that
no objects filled with liquids, such as vases, shall be placed on the
equipment. Provide a surge suppressor at the inlet opening of the
equipment under special conditions such as the mountain top,
iron tower, and forest. CAUTION: If the fuse of the device can be
replaced, replace it only with the same model to reduce the risk of
fire or electric shock. Do not touch the bare components (such as
the metal contacts of the inlets) and wait for at least 5 minutes,
since electricity may still exist after the device is powered off. For
the device powered on and off only by power plug and
socket-outlet, the socket-outlet shall be installed near the device
and easily accessible.
Battery
Do not ingest battery. Chemical burn hazard! This product
contains a coin/button cell battery. If the coin/button cell battery
is swallowed, it can cause severe internal burns in just 2 hours and
can lead to death. Keep new and used batteries away from
children. If the battery compartment does not close securely, stop
using the product and keep it away from children. If you think
batteries might have been swallowed or placed inside any part of
the body, seek immediate medical attention. CAUTION: Risk of
explosion if the battery is replaced by an incorrect type. Dispose of
used batteries according to the instructions. Improper
replacement of the battery with an incorrect type may defeat a
safeguard (for example, in the case of some lithium battery types).
Do not dispose of the battery into fire or a hot oven, or
mechanically crush or cut the battery, which may result in an
explosion. Do not leave the battery in an extremely high
temperature surrounding environment, which may result in an
explosion or the leakage of flammable liquid or gas. Do not subject
the battery to extremely low air pressure, which may result in an
explosion or the leakage of flammable liquid or gas. + identifies
the positive terminal(s) of equipment which is used with, or
generates direct current. - identifies the negative terminal(s) of
equipment which is used with, or generates direct current.
Fire Prevention
No naked flame sources, such as lighted candles, should be placed
on the equipment. The serial port of the equipment is used for
debugging only.
Hot Surface Prevention
CAUTION: Hot parts! Burned fingers when handling the parts. Wait
one-half hour after switching off before
handling parts. This sticker is to indicate
that the marked item can be hot and
should not be touched without taking
care. For device with this sticker, this device is intended for
installation in a restricted access location, access can only be
gained by service persons or by users who have been instructed
about the reasons for the restrictions applied to the location and
about any precautions that shall be taken.
Installation
Install the device according to the instructions in this manual. To
prevent injury, this device must be securely attached to the
installation surface in accordance with the installation instructions.
Never place the device in an unstable location. The device may fall,
causing serious personal injury or death. Do not install devices for
professional use in locations where children are likely to appear.
If the device is not released with a power adapter, and you need
to wire the bare cables of the device: The device external wiring
connected to the hazardous live terminals requires installation by
an instructed person. Make sure that the power has been
disconnected before you wire, install, or disassemble the device.
The power supply or device must be connected to an earthed
mains socket-outlet. High voltage for the power supply. Do not
disassemble it. If the device needs to be wired by yourself, select
the corresponding wire to supply power according to the electric
parameters labeled on the device. Strip off wire with a standard
wire stripper at corresponding position. To avoid serious
consequences, the length of stripped wire shall be appropriate,
and conductors shall not be exposed.
Power Supply
Device powered by Safety Extra-Low Voltage (SELV): The power
source should meet limited power source or PS2 requirements
according to IEC 60950-1 or IEC 62368-1 standard.
Device powered by AC mains supply voltage: The equipment must
be connected to an earthed mains socket-outlet. An appropriate
readily accessible disconnect device shall be incorporated external
to the equipment. An appropriate overcurrent protective device
shall be incorporated external to the equipment, not exceeding
the specification of the building. An all-pole mains switch shall be
incorporated in the electrical installation of the building. If the
device is powered by terminals connected to the power cord,
ensure correct voltage and wiring of the terminals for connection
to mains supply. The equipment has been designed, when
required, modified for connection to an IT power distribution
system.
White Light Illuminator (If supported)
Possibly hazardous optical radiation emitted from this product. DO
NOT stare at operating light source. May be harmful to the eyes.
Wear appropriate eye protection or DO NOT turn on the white
light when you assemble, install or maintain the camera.
Transportation
Keep the device in original or similar packaging while transporting
it.
System Security
Please understand that you have the responsibility to configure all
the passwords and other security settings about the device, and
keep your user name and password.
Maintenance
If the product does not work properly, please contact your dealer
or the nearest service center. We shall not assume any
responsibility for problems caused by unauthorized repair or
maintenance. A few device components (e.g., electrolytic
capacitor) require regular replacement. The average lifespan
varies, so periodic checking is recommended. Contact your dealer
for details.
Cleaning
Please use a soft and dry cloth when clean inside and outside
surfaces of the product cover. Do not use alkaline detergents.
Using Environment
When any laser equipment is in use, make sure that the device
lens is not exposed to the laser beam, or it may burn out. DO NOT
expose the device to high electromagnetic radiation or dusty
environments. For indoor-only device, place it in a dry and
well-ventilated environment. DO NOT aim the lens at the sun or
any other bright light. Make sure the running environment meets
the requirement of the device. DO NOT place the camera in
extremely hot, cold, dusty or damp locations, and do not expose it
to high electromagnetic radiation.
Emergency
If smoke, odor, or noise arises from the power supply or device,
Loading ...
Loading ...
Loading ...