2 COB & 1 SMD LED RECHARGEABLE
ALUMINIUM FOLDING POCKET LIGHT
MODEL NO: LED02G
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
1.1. GENERAL
9 It is important to ensure that the lamp is fully charged before initial use.
8 DO NOT turn the lamp on when it is being charged.
8 DO NOT shine directly into your, another person’s or an animal’s eyes.
8 DO NOT allow children to use the lamp.
8 DO NOT leave battery in a discharged state. Recharge battery immediately.
9 Recharge the battery at least once every six months of non-use.
9 There are no user serviceable components. DO NOT dismantle.
8 DO NOT pull the charger plug from the mains socket by the lead.
1.2. BATTERY SAFETY
WARNING! To reduce the risk of burns or re:
8 DO NOT Attempt to open, disassemble, modify or service the battery pack.
8 DO NOT Crush, puncture, short external contacts or dispose of in re or water.
8 DO NOT Expose to temperatures above 60°C (140°F).
9 Recycle or dispose of used battery as stipulated by local regulation.
9 If the electrolyte in the cells gets on your skin, thoroughly rinse with water. If it gets in your eyes, rinse thoroughly with cool
water and seek immediate medical attention.
2. INTRODUCTION
Slimline pocket light for use in conned spaces. Durable aluminium housing. Inspection arm can be folded 180º. Super bright COB and SMD
LED, 6500k. Rechargeable high quality 3.7V 2600mAh Lithium-ion battery. LED Indicators - ash green for charging and continuous green for
fully charged. High-impact IK07 Rated. Strong magnet on base of handle for hands-free use.
3. SPECIFICATION
MODEL NO: ............................................................ LED02G
Battery: .................................................3.7V 2600mAh Li-ion
Charging Time: ..................................................................4hr
LED Type: ...............................................2 x COB + 1 x SMD
Length: ...................................................................................
Folded: ........................................................ 162 x 29 x 40mm
Extended: ....................................................304 x 29 x 33mm
Lumen Output:
Top: .............................................................................. 120lm
Front(High/low): .................................................800lm/150lm
Rear(High/low): ..................................................... 400/120lm
Operating Time: .....................................................................
Top Spotlight: ........................................(120lm)/(8hr runtime)
Front Light: ............................ (800/150lm) (2.5hr/8hr runtime)
Rear Light: ..................................(400/120lm)/(4/9hr runtime)
4. CHARGING
4.1. The battery fitted to this light is considered to be a consumable item and its ability to accept charge will reduce over time. We will
warranty it against mechanical and electrical defect for a period of one year, this does not cover fair wear and tear. If the battery is not
properly charged before first use, or regularly conditioned, its capacity will diminish. Under these circumstances we will not replace the
battery even if it is less than one year old.
4.2. Connect the charger into the charge port on the light. Plug into power supply and turn on, the green charge indicator LED on the light
will flash as the battery charges. When fully charged the three LEDs turns to continuous green.
4.3. Charge the battery for 4-5 hours for its initial charge. Normal charge time is approx 4hrs. Disconnect from mains supply.
NOTE: The Lithium battery does not suffer from memory effect and once fully charged may be stored for up to six months without
another charge.
LED02G Issue 1 16/06/2021
Original Language Version
© Jack Sealey Limited
Refer to
instructions
5. OPERATION
NOTE: If you leave the light on one setting for more than 20 seconds, the subsequent press will turn the light o. If you then quickly press
the power button again the light will come back on at the last known setting.
5.1. First press: top spot light on
5.2. Second press: front light, half power.
5.3. Third press: front light, full power.
5.4. Fourth press: Rear light, half power.
5.5. Fifth press: Rear light, full power.
5.6. Sixth press: O.
5.7. Fully charge the light before storage.
6. MAINTENANCE
6.1. Keep light clean with a damp cloth (DO NOT use solvents) and check for damage before every use.
6.2. The battery is not designed to be removed.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 01284 703534 sales@sealey.co.uk www.sealey.co.uk
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
BATTERY REMOVAL
Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential purchasers of products
containing batteries (as defined within these regulations), that they are registered with Valpak’s registered compliance scheme. Jack
Sealey Ltd’s Batteries Producer Registration Number (BPRN) is BPRN00705.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
LED02G Issue 1 16/06/2021
Original Language Version
© Jack Sealey Limited
