Loading ...
Loading ...
Loading ...
MX101644—UN—02SEP20
3. Clean area around the dipstick to prevent debris from falling into
crankcase.
4. Disconnect oil drain hose (A) from the side of the engine and lower
hose, routing the oil drain hose down through the opening behind
the transmission oil reservoir. Ensure that the drain valve will not
drain onto the transmission housing, transmission fan, and frame.
5. Loosen dipstick (C). Remove the oil drain cap (B) and drain the oil
into an approved container until the oil has drained completely.
6. Wipe dirt from around the oil îš¿lter (D). Place a drain pan under the
oil îš¿lter and remove îš¿lter.
7. Put a light coat of fresh, clean oil on the new îš¿lter gasket.
8. Install replacement oil îš¿lter by turning oil îš¿lter to the right
(clockwise) until the rubber gasket contacts îš¿lter base. Tighten
îš¿lter an additional one-half turn.
9. After oil has drained, install the drain cap (B).
10. Attach drain hose assembly (A) to side of engine.
11. Add oil no higher than FULL mark on dipstick. Begin with per
speciîš¿cation; do not overîš¿ll.
Speciîš¿cation
Z515E Engine Oil—Capacity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.9 L
(2.0 qt)
12. Tighten dipstick.
13. Start and run engine at idle to check for leaks. Stop engine. Fix
any leaks before operating.
14. Check oil level. Add oil if necessary.
Z530M and Z530R
1. Run engine to warm oil.
2. Park machine safely on a level surface. (See Parking Safely in the
Safety section.)
IMPORTANT: Avoid damage! Dirt and contamination can enter
engine when checking oil level. Clean area around dipstick
before loosening or removing.
3. Clean area around the dipstick to prevent debris from falling into
crankcase.
MX101429—UN—22APR20
4. Disconnect oil drain hose from the side of the engine and lower
hose, routing the oil drain hose down through the opening behind
the transmission oil reservoir. Ensure that the drain valve will not
drain onto the transmission housing, transmission fan, and frame.
5. Loosen dipstick (A). Remove the oil drain cap (B) and drain the oil
into an approved container until the oil has drained completely.
6. Wipe dirt from around the oil îš¿lter (C). Place a drain pan under the
oil îš¿lter and remove îš¿lter.
7. Put a light coat of fresh, clean oil on the new îš¿lter gasket.
MX101430—UN—23APR20
8. Install replacement oil îš¿lter by turning oil îš¿lter to the right
(clockwise) until the rubber gasket contacts îš¿lter base. Tighten
îš¿lter an additional one-half turn.
9. After oil has drained, install the drain cap (B).
10. Attach drain hose assembly to side of engine.
11. Add oil no higher than FULL mark on dipstick. Begin with per
speciîš¿cation; do not overîš¿ll.
Speciîš¿cation
Z530 Engine Oil—Capacity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.1 L
(2.2 qt)
12. Tighten dipstick.
13. Start and run engine at idle to check for leaks. Stop engine. Fix
any leaks before operating.
14. Check oil level. Add oil if necessary.
Z545R
1. Run engine to warm oil.
2. Park machine safely on a level surface. (See Parking Safely in the
Safety section.)
Service Engine
33
Loading ...
Loading ...
Loading ...