OWNER'S MANUAL
AUTO EMPTY
CHARGING STATION
Before beginning installation, read these instructions
carefully. This will simplify installation and ensure that the
product is installed correctly and safely. Leave these
instructions near the product after installation for future
reference.
ENGLISH
VDS-ST1AU / VDS-ST1WU
MFL71780904
Rev.04_120522
www.lg.com
Copyright © 2021-2022 LG Electronics Inc. All Rights Reserved.
TABLE OF CONTENTS
This manual may contain images or
content that may be different from the
model you purchased.
This manual is subject to revision by the
manufacturer.
SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE...........................................................3
WARNING............................................................................................................3
CAUTION .............................................................................................................9
INSTALLATION
Product Overview.............................................................................................12
Installing the Charging Station ......................................................................15
Storing the Accessories ...................................................................................17
OPERATION
Charging the Battery .......................................................................................19
Getting Started .................................................................................................20
MAINTENANCE
Cleaning the Appliance ...................................................................................24
TROUBLESHOOTING
Before Calling for Service................................................................................28
3
SAFETY INSTRUCTIONS
ENGLISH
SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
The following safety guidelines are intended to prevent unforeseen
risks or damage from unsafe or incorrect operation of the appliance.
The guidelines are separated into ‘
WARNING
’ and ‘
CAUTION
’ as
described below.
Safety Messages
WARNING
WARNING
• To reduce the risk of explosion, fire, death, electric shock, injury or
scalding to persons when using this product, follow basic
precautions, including the following:
Technical Safety
• This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a person
This symbol is displayed to indicate matters and
operations that can cause risk. Read the part with this
symbol carefully and follow the instructions in order to
avoid risk.
WARNING
This indicates that the failure to follow the instructions can
cause serious injury or death.
CAUTION
This indicates that the failure to follow the instructions can
cause the minor injury or damage to the product.
4
SAFETY INSTRUCTIONS
responsible for their safety. Children should be supervised to ensure
that they do not play with the appliance.
• Do not allow the appliance to be used as a toy. Close attention is
necessary when used by or near children.
• Do not allow children to play with or hang on the appliance.
• Do not use the appliance with damaged power cord or plug. The cord
must be replaced. If the appliance is not working as it should, has
been dropped, damaged, left outdoors, or dropped into water, return
it to an LG Electronics service centre.
• Do not pull or carry by cord, use cord as a handle, close a door on
cord, or pull cord around sharp edges or corners. Do not run
appliance over cord. Keep cord away from heated surfaces.
• Do not unplug by pulling on cord. To unplug, grasp the plug, not the
cord.
• Place the cords from other appliances out of the area to be cleaned.
Battery
• Never use the battery and the vacuum cleaner from other appliances
with this appliance. Use only the battery and the vacuum cleaner
provided by LG Electronics.
• Use appliances only with specifically designated battery packs. Use of
any other battery packs may create a risk of injury and fire.
• Recharge only with the charger specified by the manufacturer. A
charger that is suitable for one type of battery pack may create a risk
of fire when used with another battery pack.
• Never use the battery and the charging station from this appliance
with other appliances.
• Unplug the power cord and remove the battery if the appliance will
not be used for an extended period of time.
• Do not use modified or damaged batteries.
• When disposing of the battery or the appliance, remove the battery
from the appliance and safely dispose of it.
5
SAFETY INSTRUCTIONS
ENGLISH
• Do not use a battery pack or appliance that is damaged or modified.
Damaged or modified batteries may exhibit unpredictable behavior
resulting in fire, explosion or risk of injury.
• Do not disassemble, remove or short-circuit the battery.
• Have the battery replaced when it is no longer able to hold a charge.
• Refer to the
Charging the Battery
section instructions for the
method of replacing the battery.
• When disposing of this appliance, follow regulations for disposal of
rechargeable lithium-ion batteries.
• Follow all local ordinances and regulations when handling or
disposing of the battery.
• Disconnect the battery pack before cleaning or servicing.
• Prevent unintentional starting. Ensure the switch is in the off position
before connecting to the battery pack, picking up or carrying the
appliance. Carrying the appliance with your finger on the switch or
energizing an appliance that has the switch on invites accidents.
• When the battery pack is not in use, keep it away from other metal
objects, like paper clips, coins, keys, nails, screws or other small metal
objects, that can make a connection from one terminal to another.
Shorting the battery terminals together may cause burns or a fire.
• Under abusive conditions, liquid may be ejected from the battery. If
this happens, avoid contact. If contact accidentally occurs, flush with
water. If liquid contacts eyes, additionally seek medical help. Liquid
ejected from the battery may cause irritation or burns.
• Do not modify or attempt to repair the appliance or the battery pack
(as applicable) except as indicated in the instructions for use and care.
Installation
• To avoid an electrical shock or fire, do not install, charge or store the
appliance where it may be exposed to water, rainfall or high
humidity.
• Install, charge and store the appliance in a well-ventilated place.
• Avoid operating the appliance in areas where there is a risk of
leakage of flammable gas, industrial oil or metallic dust.
6
SAFETY INSTRUCTIONS
• Do not store or install the appliance, power cord or plug near heating
devices or open flames.
• Install the charging station on a firm, level surface.
• Install the device so that it does not tip over.
• To prevent tipping, self-standing mode installations should be
anchored to the wall using the provided anchoring kit.
• Use the anchoring screws only when attaching to concrete or similar
solid surfaces.
• Never drill into a wall without first checking that the area behind it is
free from power conduits, plumbing, vents, or cables.
• Do not use or store the appliance at temperatures below 5°C or
above 38°C.
• Do not store or install the appliance where it is exposed to
temperatures below freezing or exposed to outdoor weather
conditions.
• When installing or moving the appliance, be careful not to pinch,
crush, or damage the power cord or plug.
Operation
• This appliance is exclusively for use with the LG Electronics CordZero
A9 Vacuum Cleaner. Do not use it for other appliances or other
purposes.
• Use only as described in this manual. Use only manufacturer’s
recommended attachment.
• This appliance is designed for normal indoor domestic use only. It is
not to be used for any non-residential, commercial, or industrial
application.
• Do not use or store the appliance in any outdoor location, garage
environment or on wet surfaces.
• This appliance is equipped with a double insulated power cord.The
power plug must be plugged into an appropriate outlet socket that is
installed in accordance with all local codes and ordinances.
7
SAFETY INSTRUCTIONS
ENGLISH
• Do not handle the power cord, plug, or appliance controls with wet
hands.
• Wipe any moisture or dirt off the cord or plug with a dry cloth.
• Unplug the power cord using the plug, not the cord. Pulling on the
cord can damage it and result in electric shock or fire.
• Never attempt to operate this appliance if it is damaged,
malfunctioning, partially disassembled, or has missing or broken
parts, including a damaged cord or plug. Take it to an authorized LG
Electronics service centre or dealer for assistance.
• Do not apply excessive force to the power cord to bend it, or place it
under a heavy object as this will damage it.
• Do not use multiple-outlet adapters with this appliance. Make sure to
use a power socket with a capacity of 10 A.
• Do not plug the appliance into a damaged or loose outlet.
• Make sure to unplug the power cord when the appliance is not to be
used for an extended period of time.
• Do not damage, alter, excessively bend, twist, pull, pinch or heat the
power cord.
• Before using the appliance, remove any wire or string on the floor.
• Avoid touching the prongs of the power plug with your finger(s) when
unplugging the power cord.
• Do not cover the power cord with a rug or carpeting.
• Push the power plug firmly into the wall outlet so that it is not loose.
• If the product has been submerged, contact an LG Electronics service
centre or dealer for instructions before resuming use.
• If the product makes a strange noise or emits an odor or smoke,
discontinue use and contact an LG Electronics customer information
centre.
• Only qualified technicians or service personnel from LG Electronics
may disassemble, repair or modify the appliance.
• Never insert a sharp metal object such as a pin, nail or knife in a hole
or gap in the appliance or the charging station.
8
SAFETY INSTRUCTIONS
• Make sure that no water, beverage or detergent gets inside the
appliance or the charging station.
• Do not allow children to use the appliance.
• Do not let children or pets get close to the appliance when using,
charging or storing.
• Keep clothing and hair, fingers, or other parts of the body away from
openings and moving parts.
• Do not use in an enclosed space where vapors are present from paint
thinner, mothproofing substances, flammable dust or other
explosive or toxic materials.
• Make sure that the filter is installed before use.
• Do not touch the charging terminals on the appliance or the charging
station, or insert an electrified object inside the appliance or the
station.
• Do not lean the appliance on walls, chairs or tables.
• If the earth leakage breaker is tripped when the product is put on the
charging station, immediately remove the appliance from the
charging station. Contact an LG Electronics customer service centre.
• Do not use or store a heating device or flammable substance (ether,
benzene, alcohol, chemicals, combustible sprays, insecticide, air
freshener or cosmetics) in close proximity to the appliance.
• Do not attempt to clean up a liquid substance (water, beverage),
odorous substances (candy, chocolate, pet excrement), metal objects
(blades, pins), flammable substances, surfactants, or glass shards
with this appliance.
• In the event of a gas leak (natural gas, propane gas, etc.) do not
operate this or any other appliance. Open a window or door to
ventilate the area immediately.
• Do not hold the charging station upside down with the battery in the
charging station.
• Do not expose the appliance, and the battery in particular, to heat, a
heating device or direct sunlight.
• Do not keep the appliance or its battery inside a vehicle which is
exposed to direct sunlight.
9
SAFETY INSTRUCTIONS
ENGLISH
• Never allow any water, beverage or detergent to get inside the
battery.
• Do not apply physical impacts to the battery.
• Do not use the appliance without the dust bag and filters in place.
Maintenance
• Make sure to unplug the power cord when cleaning or maintaining
the charging station.
• Do not spray or use water, inflammable materials such as gasoline or
thinners, or surfactants such as detergent or bath soap near the
appliance.
Disposal
• Keep packing materials out of the reach of children. Packaging
materials can pose a suffocation risk for children.
• Destroy the carton, plastic bag, and other packing materials after the
appliance is unpacked. Children might use them for play. Cartons
covered with rugs, bedspreads, or plastic sheets can become airtight
chambers.
• Dispose of this appliance according to local, state, and regional laws
and regulations.
• Contact your local city council or the related government authority
before disposing of this appliance.
CAUTION
CAUTION
• To reduce the risk of injury to persons, malfunction, or damage to the
product or property when using the appliance, follow basic safety
precautions, including the following:
Operation
• Do not open the door of the product using excessive force.
10
SAFETY INSTRUCTIONS
• Do not carry the product with the Vacuum Cleaner, nozzles, or
accessories inside; it may cause injury or product damage.
• When opening and closing the product door or control panel, be
careful not to get your fingers caught.
• Remove all the protective plastic from the Vacuum Cleaner before
use. Otherwise, it may cause abnormal noise during the dust
emptying operation.
• Keep the area around the charging station clean. A strong airstream
can be emitted from the exhaust on the back of the product, causing
dust to accumulate on the floor.
• This appliance has a built-in safety device to prevent damage from
overheating. If the appliance becomes overheated after extended
use, it may automatically turn off. If this occurs, leave the appliance
in a cool, well-ventilated area for about an hour before turning on the
power again.
• Do not subject the product to shocks or drop it.
• Do not install wet or damp filters.
• Do not clean the product with a volatile or organic solvent (thinner or
acetone).
• Always use a soft cloth to clean the appliance.
• Remain aware of your surroundings while using the appliance to
avoid colliding with people or animals.
• Do not kick or apply force to the appliance.
• Do not put any object other than the appliance, especially a metallic
or magnetic object, on the charging station.
• Keep fingers away from pinch points when assembling the appliance
or the charging station.
• Do not let a child or a pet hang onto the charging station.
• Follow all applicable state and local codes and regulations when
installing the mounting station.
• Do not use the double-sided tape to anchor the charging station on
wallpaper. Use the provided screws to anchor the charging station.
The weight of the charging station and the appliance could damage
the paper.
11
SAFETY INSTRUCTIONS
ENGLISH
• Do not remove the battery during operation.
12
INSTALLATION
INSTALLATION
Product Overview
The images in this guide may be different from the actual components and accessories, which are subject
to change by the manufacturer without prior notice for product improvement purposes.
Front View
*1 There is also a nozzle hook on the right.
NOTE
• Use the charging station only with the provided vacuum cleaner. Using a vacuum cleaner other than the
one designed to be used with the charging station, as improper sealing of the products may result and
dust not being emptied from vacuum cleaner.
Part Name Part Name
a
Control Panel
f
Motor Protection Filter (Expendable)
b
Vacuum Cleaner Mounting Unit
g
Exhaust Filter (Expendable)
c
Nozzle Hook
*1
h
Cleaning Brush
d
Bedding Nozzle or Pet Nozzle
i
Crevice Tool
e
Dust Bag (Expendable)
j
Combination Tool
13
INSTALLATION
ENGLISH
Accessories
Included Accessories
a
Dust Bag (Expendable)
Installation Kit
a
String (Including the slide and loop)
b
Fixing Rack (2EA)
c
Wall Fixing Screw
d
Wall Fixing Anchor
e
Product Fixing Screw
NOTE
• The dust bag exhaust filter and the motor
protection filter will eventually need to be
replaced. Contact an LG Electronics customer
service center.
Specifications
Appliance
Battery
The charging station allows you to charge two batteries but charge one battery at a time.
The spare battery will start charging only when the battery in the vacuum cleaner is fully charged.
Model
VDS-ST1******
Dimensions
(Width X Depth X
Height)
255 mm X 297 mm x 1009 mm
Weight
Approximately 10.1 kg
Power Consumption
1700 W (Cleaning)
0.4 A (Charging)
Input
220 - 240 V~ 50 Hz
Output
DC 28.3 V / 1.15 A
14
INSTALLATION
NOTE
• The number of batteries varies depending on the vacuum cleaner purchased. The spare battery is
available to buy separately.
Model
EAC633822**
Voltage
DC 25.9 V
Capacity
2400 mA
15
INSTALLATION
ENGLISH
Installing the Charging
Station
Installation
Follow the steps below to install the charging
station on a hard and level floor.
CAUTION
• Do not install on carpeted floors or rugs. The
product may fall, causing injury or damage.
1
Place the product on a flat, hard surface.
• During installation, allow 5cm clearance in
the the rear and a radius of 20cm to the front
& sides to be able to open both doors of the
product.
• When storing with the mop nozzle, install
the product further away from the wall.
2
Using the anti-tip kit, fix the product firmly to
the wall.
• You may need to seek professional help to
assist with securing product to wall using
anti-tip kit.
3
Plug the power plug into the outlet.
• When the power plug is connected correctly,
the status display flashes, and the product
setting is initialized. Once initialization is
completed, the status display turns off.
• Use a velcro tie to bind and tidy the excess
cable.
Anti-tip Kit Installation
Anti-tip kit is intended to secure the product to the
wall firmly in order to prevent the product from
falling over or tipping,which may lead to personal
injury, or product or floor damage. Install and use
the kit in the following manner.
WARNING
• Carefully read and follow the guidelines in order
to prevent property damage or personal injury.
• Do not lean against the product or place a heavy
object on top of it.
5 cm
20 cm
16
INSTALLATION
WARNING
• Manage and supervise children or pet animals to
prevent them from bumping into product and
falling, or clinging to the product.
• If you prefer not to install this kit immediately,
ensure that you keep it out of the reach of
children as this may pose a choking hazard.
• Do not use this kit for purposes other than the
installation of the charging station.
• When drilling holes for mounting of anti-tip kit,
use caution and wear gloves, protective clothing
& protective goggles to prevent personal injury.
• If there is a pipe (gas pipe, water pipe, pneumatic
pipe, etc.), an electric cable or an electric wire
behind the wall, do not install the product on
that wall.
1
Before moving the product to its final position,
decide on a proper position for installing the
wall fixing anchor
• Install the wall fixing anchor and the fixing
rack directly behind the product.
2
Insert the fixing rack into the loop at the end of
the string and insert the provided wall fixing
screw into the fixing rack screw hole.
3
Drill a 4 mm wide and 44.5 mm deep hole at the
selected position on the concrete wall and
insert the wall fixing anchor into the hole. Fix
the fixing rack to the wall firmly using the wall
fixing screw.
4
Insert the nearest string into the slide knot and
form a loop as shown in the figure. Insert the
fixing rack into the loop and insert the product
fixing screw into the fixing rack screw hole.
5
Align the screw hole on the fixing rack with the
hole at the back of the product and fix the
fixing rack to the product firmly by fastening
the product fixing screw.
6
Adjust the length of the string on the slide by
pulling it in accordance with the gap between
the wall and the product.
CAUTION
• Do not tighten the wall fixing screw excessively.
Doing so may cause the wall fixing to become
loose and the product to fall, resulting in
personal injury or product damage.
• Use the fixing rack only if the wall is a concrete or
solid wall. If the wall is not solid and the product
falls, personal injury or product damage may
result.
• Do not insert the fixing rack into the loop in the
middle. Doing so may cause the slide to slip after
5 cm
17
INSTALLATION
ENGLISH
the product falls, resulting in personal injury or
product damage.
• If the distance between the wall and the product
is too great, the product may fall.
Storing the Accessories
Storing the Tools
Use the product to store the inlet and components
provided with the vacuum cleaner.
The components may differ depending on the
vacuum cleaner model.
Storing on Sides
1
Open the nozzle hook
a
on both sides of the
product.
• To open the nozzle hooks, press on the right
side. Be careful not to pinch fingers when
opening.
2
Hang the nozzle on the nozzle hook.
Storage Inside
1
Open the left door of the product and insert
the bedding nozzle or the pet nozzle
a
for
storage.
2
Open the right door and insert the
combination tool
b
, the crevice tool
c
and the
cleaning brush
d
for storage.
NOTE
• Before moving the product, unplug it and
remove the vacuum cleaner, nozzles, and
accessories.
18
INSTALLATION
NOTE
• To carry the product, open both doors and hold
the areas shown.
19
OPERATION
ENGLISH
OPERATION
Charging the Battery
Before Charging the Battery
• Make sure that the adapter is connected to both
the charging station and the power outlet.
• Fully charging a single battery usually takes 4
hours. It will take twice as long to charge both
the main and spare batteries.
• The battery will not be charged if the indoor
temperature is below 5 ℃. Only charge the
battery when indoor temperatures are between
5 ℃ and 38 ℃.
• The battery will eventually need to be replaced.
Due to the battery characteristics, runtime is
shortened after using the appliance repeatedly
for an extended period.
• The last bar on the battery indicator begins to
flash when the battery needs to be recharged.
Use the appliance with a fully charged battery.
• To maintain battery life on dual-battery models,
swap the positions of the two batteries
periodically, between the main body and the
spare charging station.
Charging the Spare Battery
After the vacuum cleaner has finished charging,
the spare battery will start charging.
One or two batteries are provided. The number of
batteries varies depending on the model
purchased.
1
Lift the front of the control panel located at the
top of the charging station.
2
To insert, align the battery with the outline of
the battery charger.
3
Press the battery down into the compartment.
NOTE
• The spare battery icon (
*
) in the status display
flashes during charging and remains on when
charging is complete.
• Insert the spare battery completely. If the spare
battery is inserted correctly, the spare battery
icon (
*
) flashes.
20
OPERATION
Getting Started
Control Panel Features
Control Panel
List Descriptions
a
Status Display
The display shows the dust emptying operation status or when to replace
the dust bag, charging status of the spare battery, and dust emptying
mode.
b
Start
Press the
Start/Stop
button once to start the dust emptying operation.
• With the
Start/Stop
button is selected, a melody plays. When the
vacuum cleaner is mounted in the emptying station, the dust bin cover
opens automatically and the dust emptying operation begins.
• When you purchase the product, the manual dust emptying mode is
set by default.
Stop
Press the
Start/Stop
button once to cancel the dust emptying operation.
• When the dust emptying operation is canceled, the product returns to
the charging status.
- In the Finishing Step(the dust bin cover closes automatically), the
Start/Stop
button is inactive.
• Residual dust in the suction area may fall on the floor when the
Vacuum Cleaner is removed from the station after the dust emptying
operation is canceled.
- If the dust emptying operation is canceled, the dust bin may not be
emptied completely and dust will remain on the duct suction area.
- Complete the dust emptying operation before using the Vacuum
Cleaner.
Change Dust
Emptying Mode
Press and hold the
Start/Stop
button for at least 3 seconds to switch
between automatic or manual dust emptying mode.
(PSW\'XVW
67$57
6723
$XWR0RGH2Q2II
+ROGVHF
21
OPERATION
ENGLISH
Status Display
NOTE
• Remove all the protective plastic from the vacuum cleaner before use. Otherwise, it may cause abnormal
noise during the dust emptying operation.
• Ensure cyclonic mesh filter is firmly attached to hand stick cleaner to avoid cyclonic mesh filter from
becoming dislodged during automatic dust emptying mode.
List Descriptions
a
Dust Emptying
(Replace Bag)
Indicator
• Indicates the dust emptying operation status or when to replace the
dust bag.
- White: Product is emptying dust.
- Flashing red: If the indicator flashes red while emptying dust, this
indicates dust bag requires replacement. At the end of dust
emptying operation, replace dust bag.
- Flashing red, beeping: If the dusty emptying operation is complete
and the dust bag is full, the indicator will flash red, beep 10 times
and then turn off.
- If the indicator flashes red, replace the dust bag to maintain product
performance.
b
Spare Battery
Indicator
• Indicates the charging status of the spare battery.
- Flashes: When the spare battery is mounted in the charger.
- On (steady): Spare battery charging is complete.
- The spare battery will not charge until the battery mounted in the
vacuum cleaner is fully charged. Check the battery level on the
handle of the vacuum cleaner to check whether charging is
complete.
c
Auto Emptying
Indicator
• Lights to indicate that the automatic dust emptying mode is on.
- Automatic dust emptying mode automatically starts the operation
every time the vacuum cleaner is mounted correctly onto the
product.
- If you remove the vacuum cleaner and mount it immediately, dust
emptying operation may not start automatically, depending on the
circumstance. If it doesn't start automatically, select the
Start/Stop
button to start.
AUTO
22
OPERATION
Using the Product
Using the Manual Mode
1
Insert the vacuum cleaner into the product.
• After adjusting the length adjustment pipe
of the vacuum cleaner to the shortest length,
attach it to the product.
• If vacuum cleaner pipe is connected to a
combination tool or crevice tool, the vacuum
cleaner will not fit inside the emptying
station. Mount vacuum cleaner to emptying
station with combination too or crevice tool
attached.
• If the vacuum cleaner fits properly inside the
product, the alarm will sound. If the alarm
does not sound, reinsert the vacuum
cleaner.
• Before starting the dust emptying operation,
pull the easy dust emptying lever on the
vacuum cleaner down 2 or 3 times to sweep
away the dust to make the operation easier.
2
Press the
Start/Stop
button. The dust
emptying (replace bag) icon flashes white, and
the dust emptying operation begins along with
a melody.
3
When the dust emptying operation is
complete, a melody sounds, the dust emptying
(replace bag) icon turns off, and the vacuum
cleaner starts charging.
Using the Auto Mode
When the automatic dust emptying mode is set,
the dust emptying operation starts automatically
whenever the vacuum cleaner is properly inserted
into the product.
1
Press and hold
Start/Stop
for 3 seconds to
change from the Manual mode to the Auto
mode.
2
Insert the vacuum cleaner into the product.
3
When the dust emptying operation is
complete, a melody sounds, the dust emptying
(replace bag) icon turns off, and the vacuum
cleaner starts charging.
WARNING
• Do not wash the vacuum cleaner body or the
inlet with water. If water enters the built-in
motor, it can cause electric shock or fire.
CAUTION
• Do not forcibly remove the vacuum cleaner
during the dust emptying operation. Since the
vacuum cleaner is mounted, the product may
break or fall, causing injury or product damage.
- Remove the vacuum cleaner after the dust
emptying (replace bag) icon in the status
display is turned off completely.
• Do not put foreign objects such as hands,
garbage, toys in the dust suction area of the
product without a vacuum cleaner mounted.
• Do not push, pull, or lean on the product; it may
fall, causing injury or damage.
• Do not put objects like smartphones on the
product's control panel. The product may
malfunction due to vibration, or the object may
fall to the floor, causing injury or damage.
• If the power suddenly turns off during the dust
emptying operation, you will be unable to
remove vacuum cleaner from emptying station.
Causes for power loss include a power outage, a
turned off power strip, an unplugged power
cord, and a tripped circuit breaker.
23
OPERATION
ENGLISH
• Once power is restored, product will reset and
then product can be removed from emptying
station.
NOTE
• The sound of the high-performance motor may
be louder than the existing wireless vacuum
cleaner. It is normal to hear sounds such as the
vacuum cleaner, dust bin cover opening,
product operating unit, and suction.
• During the vacuum cleaner dust emptying
operation, a stronger suction force is applied
just before the dust emptying operation finishes.
The sound may increase, however this is normal
and does not indicate a fault.
• During the dust emptying operation, the
product and spare battery are not charged for
safety reasons.
• Replace the dust bag every 3 months to maintain
the dust emptying performance. The frequency
of replacing dust bag may vary depending on the
environment.
• The dust bin may not be emptied completely
under certain conditions (very full, contains long
hairs, etc.). If this happens, press
Start/Stop
to
repeat the emptying process.
• Clean the dust bin's inside, the easy dust
emptying lever and the large dust separator to
remove remaining dust. For more information,
see the vacuum cleaner owner's manual.
• The AUTO dust emptying function may not be
able to remove dust and debris from the
cleaner’s canister if the Kompressor lever
function has been used repeatedly. A build-up of
compressed dust and debris within the canister
from using the Kompressor lever repeatedly, will
need to be removed by hand after using the
AUTO function.
24
MAINTENANCE
MAINTENANCE
Cleaning the Appliance
Cleaning the Product Body
1
Disconnect the power plug from the outlet.
2
Wipe the control panel using a soft cloth.
• Product may malfunction if there is dust on
the control panel.
3
Clean the dust around the dust suction area
using a vacuum cleaner.
Changing the Dust Bag
1
Open the left and right doors of the
component storage.
2
Hold the product with one hand and open the
dust bag door with the other hand.
25
MAINTENANCE
ENGLISH
3
Press
n
button
a
above the
PUSH
label with
one hand. The dust bag is released.
4
Pull out the dust bag lever
b
to remove the
dust bag.
• As the dust bag is pulled out, the top
opening is closed.
5
Throw away the dust bag.
6
Prepare a new dust bag.
• To avoid odors, do not reuse the dust bags.
7
Place the end of the dust bag on the rail inside
the product.
8
Slide the dust bag in along the rails of the
product until it is completely inserted.
9
Grab the dust bag lever
b
and push it up until
you hear a "click" sound.
26
MAINTENANCE
NOTE
• The dust bag door will not close without a dust
bag. Discard the dust bag and be sure to put a
new dust bag in place.
• Replace the dust bag once every 3 months. The
replacement cycle may vary depending on the
environment.
• Replace the dust bag if it smells, even if it is not
full.
• The motor protection filter will eventually need
to be replaced. Contact an LG Electronics
customer service centre.
Cleaning the Filters
Clean the motor protection filter and the exhaust
filter every 3 months or sooner if the dust emptying
function seems weaker.
• Clean the filters more frequently if the appliance
is used regularly or in areas with a lot of dust.
CAUTION
• Do not use the appliance without the exhaust
filter and the motor protection filter installed.
Doing so could result in product damage.
1
Open the left and right component storage
doors.
2
Hold the product with one hand and open the
dust bag door with the other hand.
3
Hold the product with one hand and take out
the motor protection filter with the other hand.
4
To remove the exhaust filter, hold the bottom
of the product and pull the handle end of the
filter.
27
MAINTENANCE
ENGLISH
5
Remove dust from the motor protection filter
and exhaust filter once every 3 months and
wash it using room temperature water.
• To avoid odor and the malfunction of the
motor, allow the motor protection filter and
the exhaust filter to dry completely in a well-
ventilated area out of direct sunlight for at
least 24 hours before reassembling.
6
Push the motor protection filter and exhaust
filter back into thier original positions.
• Make sure that the filters are in place before
using the product.
28
TROUBLESHOOTING
TROUBLESHOOTING
Before Calling for Service
Operation
Symptoms Possible Cause & Solution
Dust emptying doesn't
work.
The power plug is not connected.
• Connect the power plug to an outlet.
The Vacuum Cleaner is not properly inserted into the product.
• Remove the Vacuum Cleaner and reinsert it. If it is installed properly, a
beep will sound.
Dust emptying operation is stopped.
• When the Dust Emptying Start/Stop button is pressed, the dust emptying
operation starts from the beginning.
It is set to automatic or manual dust emptying mode.
• When you purchase the product, the manual dust emptying mode is set by
default. After inserting the Vacuum Cleaner into the product, pressing the
Dust Emptying Start/Stop button starts the dust emptying operation.
• When it is in automatic dust emptying mode, the dust emptying operation
starts automatically whenever the vacuum cleaner is properly inserted
into the product.
Product setting
initialization doesn't
work even after the
power plug is plugged
in again.
The internal motor of the product is not operating properly .
• Disconnect the power plug from the outlet and contact an LG Electronics
Service Centre.
The power supply has
been cut off.
The power supply has been cut off.
• Check whether the power plug is connected correctly to the outlet.
• If using a multi-outlet strip, make sure the strip is turned on.
• Check if the breaker is tripped or there is a power outage.
It won't charge. It is not plugged in.
• Plug it into an outlet.
There is a foreign object on the charging terminals.
• After unplugging from the outlet, wipe off any foreign matter from the
charging terminal with a dry cloth.
The room temperature was 5 °C or less during charging.
• Charging may not work if the temperature where you are charging is 5 °C
or less. Before use, fully charge the vacuum cleaner at a temperature
above 5 °C.
29
TROUBLESHOOTING
ENGLISH
It won't charge. The vacuum cleaner is not properly inserted into the product.
• When the vacuum cleaner is properly inserted into the product, a beep
sounds. If the beep does not sound, reinsert the vacuum cleaner.
The auxiliary battery is not properly inserted into the product.
• Push in the auxiliary battery all the way. When the auxiliary battery is
properly inserted, the auxiliary battery icon flashes.
The product has a
strange smell.
The product is purchased within 3 months.
• The odors from manufacturing the product should be gone within 3
months.
The Vacuum Cleaner smells.
• After cleaning with the mop nozzle, the wet dust may emit an odor. After
finishing cleaning, remove the damp dust from the mop nozzle before
storing the vacuum.
• The pre-filter, exhaust filter, or large dust separator may smell after
washing if it isn’t dried completely. After washing with water, dry them
thoroughly in well-ventilated shade for at least 24 hours before using them
again.
The dust bag smells.
• If you clean foreign matter that smells (such as pet excrement) with an
vacuum cleaner, the vacuum may smell even if you do not have a full dust
bag. Replace the new dust bag even if it isn't full.
• If you have not replaced the dust bag for a long time, it may smell. Replace
it with a new dust bag even if it isn't full.
Two icons [dust
emptying (replace bag)
and auxiliary battery]
flash simultaneously.
The motor that holds the Vacuum Cleaner isn't working properly.
• Disconnect the power plug from the outlet and contact an LG Electronics
Service Centre.
The motor that opens and closes the Vacuum Cleaner dust bin cover isn't
working properly.
• Disconnect the power plug from the outlet and contact an LG Electronics
Service Centre.
Two icons (auxiliary
battery and auto
emptying) flash
simultaneously.
The motor that presses the Vacuum Cleaner dust bin cover separation
button isn't working properly.
• Disconnect the power plug from the outlet and contact an LG Electronics
Service Centre.
During the dust
emptying operation,
the dust emptying
notification flashes
red.
The dust bag is full.
• Throw away the used dust bag and replace it with a new dust bag.
Symptoms Possible Cause & Solution
30
TROUBLESHOOTING
The dust emptying
notification flashes red
for about 10 seconds,
and a beep sounds.
The dust bag is full.
• Throw away the used dust bag and replace it with a new dust bag.
Symptoms Possible Cause & Solution
Memo
