450 Series 36 Inch
French Door Refrigerator
in Stainless Steel
!
installing ur New Appliance
I
Before using the appliance for the first
time, you should be in formed of the
following tips.
Warning!
For proper installation, this refrigerator
must be placed on a level surface of hard
material that is the same height as the rest
of the flooring. This surface should be
strong enough to support a fully loaded
refrigerator.
The rollers, which are not castors, should
be only used for forward or backward
movement. Moving the refrigerator
sideways may damage your floor and the
rollers.
21n<h t
l/2;och
-，r
1-
乓u1r
1/2;ach
Ventilation of appliance
心 ��e
or
:二二�:�:勹�
i
:
n
:::;
energy,
it is necessary to
maintain good ventilation around the
appliance r the dissipation of heat. For
this reason, suicient clear space should
be available around the refrigerator.
Suggestion: It is advisable for there to be
at least 2.
96
i
n
ch of clearance from the
back of the fridge to the wall, at least
3
.
9
inch of clearance from its
top, at least
3
.
9
i
n
ch from its side to
the wall and a clear space in front to
allow the doors to open 125
°
. As
shown in following diagrams.
：
三
f
t
• Stand your appliance in a dry place to
avoid high moisture.
•Keep the appliance out of direct sunlight,
rain or frost. Stand the appliance away
from heat sources such as stoves, fires or
heaters.
Leveling of appliance
• For sufficient leveling and air circulating
in the lower rear section of the appliance,
the bottom feet may need to be adjusted.
You can adjust them manually by hand or
by using a suitable tool.
• To allow the doors to self-close, tilt the
top backwards by
4
0.4~0.6inch.
I I
..
'I
!'
士
'
-- - - - .
Mju吐吵b
R
F心心rllor
廿叩妇t
Installing the handles
Before you use the appliance, you have to
install the handles provided in the fridge I Tools you will need(Not provided):
chamber.
Please llow procedures below to install
and reverse the handle.
• Place the handle (A) on the door by
fitting the handle footprints over the
handle supports (C), then fasten the
screws (B) with Allen wrench
(provided in plastic).
Door Removal
In case your home access door is too
narrow for the refrigerator to pass through,
remove the refrigerator doors and drawers.
If you do not need to remove the appliance
doors, proceed to'Installing Water Lines'
on page 8.lf you need to remove the doors,
continue below.
�
三
Allen Wrench
Wrench(
o) l)I
Philips Screwdriver
1 .With the door closed, remove the 3
screws holding the top cover (A) with
Philips
(+
)
screwdriver, and then remove
5
0.1inch
(0.16inch)
0.3inch)
0.4~0.6inch
the top cover with the entire-harness
attached.
2. Take out the ice storage box (B) by
liing it up in the direction of the arrow.
2. Remove the screws (B) fixed on the
hinges with a wrench (0.3inch)and 1
ground screws(C) attached to the
hinge with Philips (
+
) screwdriver.
Remove the upper left and right door
hinges(D).
3.Use your both hands to open the door
more than 90
°
.Li it up and take it o.
I
Disassembling the freezer door
1. Pull out the freezer door and the upper
freezer drawer (A) to the final position .
3.Take out the upper freezer drawer (A) by
liing it up from the rail system.
4. Remove the lower freezer drawer (C) by
liing it up.
4.Remove the 4 hex head bolts hinges (E)
with an Allen wrench (0.1
6
inch).Remove
the lower le and right door hinges (F).
6
• Large quantity of warm food has recently been stored within
the appliance.
•The temperature outside the appliance is high.
•Doors are kept open too long or too often.
•After installing the appliance or ii has been switched o for a
long time.
Check that the air outlets are not blocked by food and ensure
A layer of frost occurs in
food is placed within the appliance to allow suicient
the compartment
ventilation. Ensure that door is fully closed. To remove the
frost, please refer to the "Cleaning and Care" chapter.
Temperature inside is
You may have left the doors open too long or too frequently; or
too warm
the doors are kept open by some obstacle; or the appliance is
located with insuicient clearance at the sides, back and top
Temperature inside is
Increase the temperature by following the "Display Controls"
too cold chapter.
Doors can't be closed
easily
Check whether the top of the refrigerator is tilted back
by 0.
4~
0.
6
inch to allow the doors to self-close, or if something
inside is preventing the doors from closing.
•The LED light may be damaged. Refer to replace LED lights
in" Cleaning and Care" chapter.
The light is not working
• The control system has disabled the lights due to the door
being kept open too long. Close and reopen the door to
reactivate the lights.
• Did you wait for 12 hours after installation of the water supply
line before making ice? If it is not suiciently cool, it may take
longer to make ice, such as when first installed.
•Is the water line connected and the water valve open?
• Did you manually stop the ice making function? Make sure
you do not set the "ice o'mode.
Ice is not dispensing
• Is there any ice blocked within the ice maker bucket or ice
chute?
• Is the water pressure less than30psi? Install a booster pump
to compensate for the low pressure.
• Is the freezer temperature too warm? Try setting the freezer
temperature lower.
•Ice maker is not making the ice fast enough. Please wait for at
least 90 minutes.
•Is the water line connected and the water valve open?
• Has the water line been crushed or kinked? Make sure the
Water dispenser is not
waterline is free and clear of any obstruction.
functioning
• Is the water tank frozen because the refrigerator temperature
is too low? Try selecting a warmer setting on the display panel.
• Check if the filter is properly installed. If it is not properly
20
