Loading ...
7
Away mode
Place and hold registered ngerprint (master or user ngerprint) on ngerprint sensor for 5
seconds to enable away mode.
Lock in away mode can be unlocked by master user ngerprint or user ngerprint which enabled
away mode. once the lock is unlocked, away mode will be disabled.
4
Delete user fingerprint
The only way to delete user ngerprint is reset the lock to factory default settings, it will delete all
user ngerprints and master user ngerprints.
5
Language settings
Press set button once and then press multi-function button on interior assembly to change voice
guide language between English and Spansih.
Double press set button to enable silent mode.
8
Restore to factory settings
Press and hold set buttons for 5 seconds using the pin tool (K). Voice prompt indicates restoration
to factory default. Yellow light ashes, and then green light ashes.
9
Emergency power supply
Use the power bank with Micro USB charger for emergency power supply When batteries run out.
Once the lock is re-activated, immediate battery replacement is requested.
Pre-Operation
Demo mode: Lock can be unlocked by any ngerprint when lock is in factory default settings (no
ngerprint registered).
Normal mode: The lock can be unlocked by registered ngerprints, and auto re-locks after 5 seconds.
Manual mode: In manual mode, the lock can be opened without ngerprint verication.
Silent mode: All voice guide will be muted in silent mode.
Away mode: In away mode, all ngerprint accesses are restricted, except master user and the user
who enables away mode.
Master user: First two ngerprints registered are master user ngerprints. Master user can be used
for lock programming. Master user ngerprint is able to unlock the door any time in any mode.
System lockdown: If wrong ngerprint attempts exceed 10 times, the system will lockdown for 3
min.
Solid blue light: Setting mode
Flashing blue light: Fingerprint recognizing succeeded when registering ngerprint
Solid green light: Fingerprint registration/verication successful/language switching successful
Flashing green light: Manual mode enabled/disabled or lock the door from inside in manual mode
Flashing yellow light: Low battery level
Flashing yellow light and then solid green light: Restore to factory default
Flashing red light: Fingerprint registration/verication failed,or system is in lockdown
Solid purple light: Away mode enabled
Flashing purple light: Away mode disabled or restrict user ngerprint in away mode
Operation
IMPORTANT: Do not load batteries until lock is completely installed.
WARNING:
Both master user ngerprints can be used for settings.
Master user ngerprint can unlock the door in any mode of lock.
Programming will be exited, if no any operation performed in 5 seconds after pressing set button.
Away mode can be disabled by master user ngerptints.
WARNING:
Maximum 50 user ngerprints (2 master user ngerprints, 48 user ngerprints) can be registered.
Same ngerprint can not be registered twice.
Programming will be exited, if no any operation performed in 5 seconds after pressing set button.
WARNING: Away mode is unavailable in Manual mode.
WARNING: All user ngerprints are deleted after reseting.
Troubleshooting
Operation (continued) Operation (continued)
Operation (continued)
Operation (continued)
Fingerprint sensor
Multi-function button
Emergency power
supply port
Set button
Indication light
Pre-Operation (continued)
NOTE: English is the default language.
6
Manual Mode
Press and hold multi-function button for 5 seconds to enable / disable manual mode and green
light ash.
In manual mode, there is no need to verify ngerprint to unlock from outside.User can press multi-
function button once to lock the door from inside and lock will enter into temporary locking state.
In temporary locking state, ngerprint verication is required to unlock from outside. This state will
exit and lock will return to manual mode after pressing multi-function button again or ngerprint
verication .
Problem Solution
Fail to set up the lock.
Check whether batteries are installed properly.
Check whether the cables is well-connected.
Make sure ngerprint is recognizable.
Check whether second master ngerprint is registered.
Yellow light keeps ashing.
The batteries are getting low. Please replace with 4 new batteries.
Fail to register ngerprint.
Make sure correct master ngerprint is entered.
Make sure your ngerprint isn't wet.
Fail to restore factory
settings.
Make sure correct reset operation is performed.
Check batteries are good
Auto Re-lock does not
function.
Make sure the lever lock is installed properly.
Make sure manual mode is disabled.
Fail to use ngerprint to
unlock.
Listen to voice guide ,Check whether lock is in away mode.
Check whether the ngerprint was registered.
Any ngerprint can open the
lever.
Make sure two master ngerprints are registered.
Master ngerprint 2 must be
added before programming?
Yes, master ngerprint 2 must be added. Master ngerprint 2 could be backup
ngerprint in case master ngerprint 1 is not recognizable.
1
Enter setting mode
If the lock is factory default, pressing set button one time by the pin tool (K) can enter setting mode
directly.
2
Register Master User fingerprints
Register master user ngerprint 1: Press the set button once.
Enter into setting mode, voice guide prompt “Entered setting mode, Please add the master
ngerprint” and blue light ash.
Place the nger on ngerprint sensor following voice guide.
Finish registering master ngerprint ,voice prompt “master ngerprint ,ngerprint added” and
green light ash.
Register master user ngerprint 2: Press the set button, veried the master user ngerprint 1, then
register master user ngerprint 2 following voice guide.
Locking and Unlocking
1
Under Nomal Mode
Use registered master user or user ngerprint to unlock from outside.
Push down lever to unlock from inside.
Lever lock will auto re-lock after 5 seconds following unlocking.
2
Under Manual Mode
Push down lever to unlock from inside or outside without ngerprint verication.
Press multi-function button once to lock the door from inside.
K
F
K
F
3
Register User fingerprints
Press set button and verify master user by scanning master user ngerprint to enter setting mode.
Place new nger on ngerprint sensor following voice guide.
PARTS ILLUSTRATIONS
LED ILLUMINATION DESCRIPTION
DEFINITION
NOTE: In temporary locking state,user can push down lever to unlock from inside, but this state will not exit.
NOTE: Batteries can last up to 12 months if locking and unlocking 10 times per day.
Loading ...
Loading ...