Loading ...
Loading ...
Loading ...
ninjakitchen.com
ninjakitchen.com
CARE & MAINTENANCE
CLEANING
Separate all parts. Wash all containers in warm, soapy water with a soft cloth.
• Hand-Washing
Wash blade assemblies in warm, soapy water using a dishwashing utensil with a handle to avoid
direct contact with the blades. Exercise care when handling blade assemblies, as the blades are sharp.
Thoroughly rinse and air-dry all parts.
• Dishwasher
Accessories are top-rack dishwasher safe but should NOT be cleaned with a heated dry cycle. Ensure
the blade assemblies are removed from their containers before placing in the dishwasher. Exercise care
when handling blade assemblies.
• Motor Base
Turn o the unit and unplug the motor base before cleaning. Wipe motor base with a clean, damp cloth.
DO NOT use abrasive cloths, pads, or brushes to clean the base.
STORING
For cord storage, wrap cord with hook-and-loop fastener near the back of the motor base. DO NOT
wrap the cord around the bottom of the base for storage. Store the unit upright and store all blade
assemblies inside or attached to their respective containers with their lids locked in place.
DO NOT store blended or unblended ingredients in the Single-Serve Cup with the Hybrid Edge™ Blades
assembly attached.
DO NOT stack items on top of the containers. Store any remaining attachments alongside the unit or in
a cabinet where they will not be damaged or create a hazard.
RESETTING THE MOTOR
This unit features a unique safety system that prevents damage to the motor and drive system should
you inadvertently overload the it. If the unit is overloaded, the motor will be temporarily disabled. Should
this occur, follow the reset procedure below.
1 Unplug the unit from the electrical outlet.
2 Allow the unit to cool for approximately 15 minutes.
3 Remove the container’s lid and blade assembly. Empty the container and ensure no ingredients are
jamming the blade assembly.
IMPORTANT: Ensure that maximum capacities are not exceeded. This is the most typical cause of
appliance overload.
If your unit needs servicing, please call Customer Service at 1-877-646-5288. So we may better assist you,
please register your product online at registeryourninja.com and have the product on hand when you call.
ORDERING REPLACEMENT PARTS
To order additional parts and attachments, visit ninjaaccessories.com.
USING THE SINGLE-SERVE CUP
1 Plug in motor base and place on a clean, dry, level surface such as a
countertop or table.
2 Add ingredients to the Single-Serve Cup. DO NOT add ingredients past the
MAX LIQUID line on the cup.
3 Install the Hybrid Edge Blades Assembly onto the top of the cup. Twist
the lid clockwise until it’s sealed tightly.
4 Turn the cup upside down and install on the motor base. Align the tabs on the cup
with the slots on the base, then rotate cup clockwise until it clicks into place. Once the
cup is locked in place, press the Power button to turn unit on. The BlendSense™
program will illuminate.
IMPORTANT: Review all warnings at the beginning of this Owner’s Guide before proceeding.
5a If using the BlendSense program, simply press the dial. The program will automatically
stop once complete. To stop the unit at any time, press the dial again.
5b If using a Manual program, select MANUAL then use the dial to select your desired
speed (LOW, MEDIUM, or HIGH). To start, press the dial. Once the ingredients have
reached your desired consistency, press the dial again or wait 60 seconds for the
unit to come to a complete stop.
6 To remove the cup from the motor base, turn the cup counterclockwise and
then lift up.
7 Remove the Hybrid Edge Blades Assembly by twisting the cap counterclockwise.
DO NOT store blended contents with blade assembly attached. Exercise care
when handling the blade assembly, as the blades are sharp.
8 Turn the unit o by pressing the Power button. Unplug the unit when finished.
Refer to the Care & Maintenance section for cleaning and storage instructions.
9 To enjoy your drink on the go, place the Spout Lid onto the cup and twist lid
clockwise until firmly sealed. For storing ingredients in the cup, use only the
Spout Lid to cover.
NOTE: Processing Mode programs are only compatible with the pitcher.
WARNING:
• Handle the Hybrid Edge™ Blades Assembly with care, as the blades are sharp.
• Remove utensils prior to processing. Failure to remove may cause the Single-Serve Cup to be damaged or to
shatter, which may cause personal injury.
•
DO NOT blend hot, eervescent, or carbonated liquids. Doing so may cause excessive pressure buildup, resulting in
risk of laceration and/or the user being burned.
• DO NOT process or grind dry ingredients.
• Remove the Hybrid Edge Blades Assembly from the Single-Serve Cup upon completion of blending. DO NOT store
ingredients before or after blending them in the cup with the blade assembly attached. Some foods may contain
active ingredients or release gases that will expand if left in a sealed container, resulting in excessive pressure buildup
that can pose a risk of injury.
Loading ...
Loading ...