BAUMR-AG TOLWBNBMRA6XL Steel Workbench LED Worklight User Manual

User Manual

[Revision 4.0 October 2022]

READ THIS MANUAL CAREFULLY BEFORE USE – FAILURE TO DO SO MAY RESULT IN INJURY, PROPERTY DAMAGE AND MAY

VOID WARRANTY. • KEEP THIS MANUAL FOR FUTURE REFERENCE. • Products covered by this manual may vary in appearance,

assembly, inclusions, specifications, description, and packaging.

Multi-Function Workbench

Safety

Safety messages are designed to alert you to possible dangers or hazards that could cause death, injury or

equipment or property damage if not understood or followed. Safety messages have the following symbols:

You WILL be KILLED or

SERIOUSLY INJURED if you do

not follow instructions.

You CAN be KILLED or

SERIOUSLY INJURED if you do

not follow instructions.

You CAN be INJURED if you do

not follow instructions or equipment

damage may occur.

It is vital that you read and understand this

user manual before using the product,

including safety warnings, and any assembly

and operating instructions. Keep the manual

for future reference.

Safety precautions and recommendations

detailed here must be fully understood and

followed to reduce the risk of injury, fire,

explosion, electrical hazard, and/or property

damage.

Safety information presented here is generic

in nature – some advice may not be

applicable to every product. The term

"equipment" refers to the product, be it

electrical mains powered, battery powered or

combustion engine powered.

• Before Use - If you are not familiar with the

safe operation/handling of the equipment or

are in any way unsure of any aspect of

suitability or correct use for your

application, you should complete training

conducted by a person or organization

qualified in safe use and operation of this

equipment, including fuel/electrical handling

and safety.

• Do NOT operate the equipment in

flammable or explosive environments, such

as in the presence of flammable liquids,

gases, or dust. The equipment may create

sparks or heat that may ignite flammable

substances.

• Keep clear of moving parts.

• Equipment may be a potential source of

electric shock or injury if misused.

• Do NOT operate the equipment if it is

damaged, malfunctioning or is in an

excessively worn state.

• Do NOT allow others to use the equipment

unless they have read this manual and are

adequately trained.

• Keep packaging away from children - risk

of suffocation! Operators must use the

equipment correctly. When using the

equipment, consider conditions and pay

due care to persons and property.

General Work Area Safety

• Work areas should be clean and well it.

• Do not operate the equipment if

bystanders, animals etc are within

operating range of the equipment or the

general work area.

• If devices are provided for connecting dust

extraction / collection facilities, ensure

these are connected and used properly.

Dust collection can reduce dust-related

hazards.

General Personal Safety

• Wear appropriate protective equipment

when operating, servicing, or when in the

operating area of the equipment to help

protect from eye and ear injury, poisoning,

burns, cutting and crush injuries. Protective

equipment such as safety goggles,

respirators, non-slip safety footwear, hard

hat, hearing protection etc should be used

for appropriate equipment / conditions.

Other people nearby should also wear

appropriate personal protective equipment.

Do not wear loose clothing or jewellery,

which can be caught in moving parts. Keep

hair and clothing away from the equipment.

• Stay alert and use common sense when

operating the equipment. Do not over-

reach. Always maintain secure footing and

balance.

• Do not use the equipment if tired or under

the influence of drugs, alcohol, or

medication.

• This equipment is not intended for use by

persons with reduced physical, sensory, or

mental capabilities.

General Fuel Safety

• Petrol/fuel/gasoline is extremely flammable

– keep clear of naked flames or other

ignition sources.

• Do not spill fuel. If you spill fuel, wipe it off

the equipment immediately – if fuel gets on

your clothing, change clothing.

• Do NOT smoke near fuel or when

refuelling.

• Always shut off the engine before

refuelling.

• Do NOT refuel a hot engine.

• Open the fuel cap carefully to allow any

pressure build-up in the tank to release

slowly.

• Always refuel in well ventilated areas.

• Always check for fuel leakage. If fuel

leakage is found, do not start, or run the

engine until all leaks are fixed.

General Carbon-Monoxide Safety

• Using a combustion engine indoors CAN

KILL IN MINUTES. Engine exhaust

contains carbon-monoxide – a poison you

cannot smell or see.

• Use combustion engines OUTSIDE only,

and far away from windows, doors, and

vents.

General Equipment Use and Care

• The equipment is designed for domestic

use only.

• Handle the equipment safely and carefully.

• Before use, inspect the equipment for

misalignment or binding of moving parts,

loose components, damage, or any other

condition that may affect its operation. If

damaged, have the equipment repaired by

an authorised service centre or technician

before use.

• Prevent unintentional starting of the

equipment - ensure equipment and power

switches are in the OFF position before

connecting or moving equipment. Do not

carry equipment with hands or fingers

touching any controls. Remove any tools or

other items that are not a part of the

equipment from it before starting or

switching on.

• Do not force the equipment. Use the

correct equipment for your application.

Equipment will perform better and be safer

when used within its design and usage

parameters.

• Use the equipment and accessories etc. in

accordance with these instructions,

considering working conditions and the

work to be performed. Using the equipment

for operations different from those intended

could result in hazardous situations.

• Always keep equipment components

(engines, hoses, handles, controls, frames,

housings, guards etc) and accessories

(cutting tools, nozzles, bits etc) properly

maintained. Keep the equipment clean and,

where applicable, properly lubricated.

• Store the equipment out of reach of

children or untrained persons. To avoid

burns or fire hazards, let the equipment

cool completely before transporting or

storing. Never place or store the equipment

near flammable materials, combustible

gases, or liquids etc.

• The equipment is not weather-proof, and

should not be stored in direct sunlight, at

high ambient temperatures or locations that

are damp or humid.

• Do not clean equipment with solvents,

flammable liquids, or harsh abrasives.

• For specific equipment safety use and care,

see Equipment Safety.

Multi-Function Workbench

General Electrical Safety

• Inspect electrical equipment, extension

cords, power bars, and electrical fittings for

damage or wear before each use. Repair or

replace damaged equipment immediately.

• Ensure all power sources conform to

equipment voltage requirements and are

disconnected before connecting or

disconnecting equipment.

• When wiring electrically powered

equipment, follow all electrical and safety

codes.

• Wherever possible, use a residual current

device (RCD).

• High voltage / high current power lines may

be present. Use extreme caution to avoid

contact or interference with power lines.

Electrical shock can be fatal.

General Electrical Safety

• Electrically grounded equipment must have

an approved cord and plug and be

connected to a grounded electrical outlet.

• Do NOT bypass the ON/OFF switch and

operate equipment by connecting and

disconnecting the electrical cord.

• Do NOT use equipment that has exposed

wiring, damaged switches, covers or

guards.

• Do NOT use electrical equipment in wet

conditions or in damp locations.

• Do NOT use electrical cords to lift, move or

carry equipment.

• Do NOT coil or knot electrical cords, and

ensure electrical cords are not trip hazards.

General Service Information

• The equipment must be serviced or

repaired at authorised service centres by

qualified personnel only.

• Replacement parts must be original

equipment manufacturer (OEM) to ensure

equipment safety is maintained.

• Do NOT attempt any maintenance or repair

work not described in this manual.

• After use, the equipment and components

may still be hot – allow the equipment to

cool and disconnect spark plugs and/or

electrical power sources and/or batteries

from it before adjusting, changing

accessories, or performing repair or

maintenance.

• Do NOT adjust while the equipment is

running.

• Perform service-related activities in suitable

conditions, such as a workshop.

• Replace worn, damaged or missing

warning/safety labels immediately.

ASSEMBLY PRECAUTIONS

• Assemble only according to these instructions. Improper assembly can create hazards.

• Wear ANSI-approved safety goggles and heavy-duty work gloves during assembly.

• Keep assembly area clean and well lit.

• Keep bystanders out of the area during assembly.

• Do not assemble when tired or when under the influence of alcohol, drugs, or medication.

• Weight capacity and other product capabilities apply to properly and completely assembled product only.

USE PRECAUTIONS

• This product is not a toy. Do not allow children to play with or near this item.

• Setup and use indoors only. Keep dry.

• Do not overtighten workpiece; damage to workpiece may occur. Be careful not to pinch fingers when working

• Locate Workbench on a flat, level, solid surface that can support the weight of the workpiece, Workbench, and tools.

• Use as intended only.

• Replace bulb only with same bulb size and rating.

• Inspect before every use; do not use if parts are loose or damaged.

• Do not exceed listed weight capacity, evenly distributed Be aware of dynamic loading! Sudden load movement may briefly create excess load

causing product failure.

• Maintain product labels and nameplates. These carry important safety information. If unreadable or missing, contact the manufacturer for a

replacement.

• People with pacemakers should consult their physician(s) before use. Electromagnetic fields near heart pacemaker could cause pacemaker

interference or pacemaker failure.

• WARNING! THIS PRODUCT CONTAINS LEAD, A CHEMICAL KNOWN TO CAUSE CANCER AND BIRTH DEFECTS OR OTHER

REPRODUCTIVE HARM.

GROUNDING

WARNING! TO PREVENT ELECTRIC SHOCK AND DEATH FROM INCORRECT GROUNDING WIRE CONNECTION:

• CHECK WITH A QUALIFIED ELECTRICIAN IF YOU ARE IN DOUBT AS TO WHETHER THE OUTLET IS PROPERLY GROUNDED. DO NOT

MODIFY THE POWER CORD PLUG PROVIDED WITH THE TOOL. NEVER REMOVE THE GROUNDING PRONG FROM THE PLUG. DO

NOT USE THE TOOL IF THE POWER CORD OR PLUG IS DAMAGED. IF DAMAGED, HAVE IT REPAIRED BY A SERVICE FACILITY

BEFORE USE. IF THE PLUG WILL NOT FIT THE OUTLET, HAVE A PROPER OUTLET INSTALLED BY A QUALIFIED ELECTRICIAN.

Multi-Function Workbench

GROUNDED TOOLS: TOOLS WITH THREE PRONG PLUGS

• Tools marked with “Grounding Required” have a three-wire cord and three prong grounding plug. The

plug must be connected to a properly grounded outlet. If the tool should electrically malfunction or break

down, grounding provides a low resistance path to carry electricity away from the user, reducing the risk

of electric shock.

• The grounding prong in the plug is connected through the green wire inside the cord to the grounding

system in the tool. The green wire in the cord must be the only wire connected to the tool’s grounding

system and must never be attached to an electrically “live” terminal.

• The tool must be plugged into an appropriate outlet, properly installed and grounded in accordance with

all codes and ordinances. The plug and outlet should look like those in the preceding illustration.

DOUBLE INSULATED TOOLS: TOOLS WITH TWO PRONG PLUGS

• Tools marked “Double Insulated” do not require grounding. They have a special double insulation

system which satisfies OSHA requirements and complies with the applicable standards of

Underwriters Laboratories, Inc., and the National Electrical Code.

• Double insulated tools may be used in either of the 120-volt outlets shown in the preceding

illustration.

EXTENSION CORDS

• Grounded tools require a three-wire extension cord. Double Insulated tools can use either a two or

three wire extension cord.

• As the distance from the supply outlet increases, you must use a heavier gauge extension cord.

Using extension cords with inadequately sized wire causes a serious drop in voltage, resulting in

loss of power and possible tool damage. (See Table A.)

• The smaller the gauge number of the wire, the greater the capacity of the cord. For example, a 14-gauge cord can carry a higher current than a

16-gauge cord. (See Table A.)

• When using more than one extension cord to make up the total length, make sure each cord contains at least the minimum wire size required.

(See Table A.) If you are using one extension cord for more than one tool, add the nameplate amperes and use the sum to determine the

required minimum cord size. (See Table A.)

• If you are using an extension cord outdoors, make sure it is marked with the suffix “W-A” to indicate it is acceptable for outdoor use.

• Make sure the extension cord is properly wired and in good electrical condition. Always replace a damaged extension cord or have it repaired by

a qualified electrician before using it.

• Protect the extension cords from sharp objects, excessive heat, and damp or wet areas.

Multi-Function Workbench

Safety Symbols

The product may have safety warning labels attached to it, explained below. Understand the symbols on your

product and their meanings. If any stickers become unreadable, unattached etc., replace them.

Flammable Material Hazard

Flammable liquids, gases, or

substances etc may present.

Avoid ignition sources and open

flames. Danger of fire.

Read User Manual

Read and fully understand

product safety warnings,

operation, procedures etc before

using the product.

Use Hand Protection

Wear appropriate hand protection

and take due care as the product

or use of the product may present

hand hazards.

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be fatal.

Electrocution / Electrical Shock

Hazard

High voltage or high current

electricity may be present or

required by the product. Take

due care when handling electrical

products, cables, plugs and

leads. Electrical shock can be

fatal.

Toxic Fumes / Dust Hazard

Using the product or by-products

from use may produce fumes,

smoke or particles that could be

harmful if inhaled. Wear

appropriate breathing protection

and have adequate ventilation.

Explosive Material Hazard

Combustible liquids, gases, or

substances etc may be present.

Avoid ignition sources and open

flames. Danger of explosion.

Cutting / Amputation Hazard

The product may have blades,

edges or mechanical devices that

can cause severe cut injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Crush Hazard

The product may have blades,

edges or mechanical devices that

can cause severe crush injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Single Operator Only

The product must be operated by

a single person only. More than

one person operating the product

may introduce additional hazards.

Use Face Protection

Wear appropriate full-face

protection and take due care as

the product or use of the product

may present face and eye

hazards.

Use Foot Protection

Wear appropriate foot protection

and take due care as the product

or use of the product may present

foot hazards.

Use Eye / Ear / Head Protection

Wear appropriate eye and / or

ear and / or head protection and

take due care as the product or

use of the product may present

eye, hearing, and head hazards.

Running Hazard

Do not run on or near the product

as doing so may present a fall

hazard.

Diving Hazard

Do not dive into the product as

doing so may present a neck /

head injury hazard.

Adult Supervision Required

Always supervise children and

other users of a product to

prevent drowning or injury.

Skin Penetration / Puncture

Hazard

The product may produce

pressure, emit liquids or objects

that can cause severe injury to

fingers, limbs, blood etc. Take

due care when handling and

using the product.

Hot Surface Hazard

Be aware that the product may

produce high temperatures and

hot surfaces that can cause burn

injuries.

Flying Debris Hazard

Be aware that the product or use

of the product may present

hazards produced by flying

debris. Wear appropriate clothing

and protective devices.

Moving Parts Hazard

Be aware that the product

contains or uses mechanical

devices that move or rotate.

Always wait for moving parts to

stop fully before handling the

product, adjusting, maintenance

etc.

Multi-Function Workbench

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be fatal.

Pull Hazard

Be aware that the product

contains or uses mechanical

devices that can pull in objects

and can cause severe injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Slope / Fall Injury Hazard

Be aware that using the product

on sloping surfaces or in slippery

conditions may present additional

dangers from falls and contact

with blades, moving parts, hot

surfaces etc.

"Slam Dunk" Warning

Do NOT attempt "slam dunk"

manoeuvres as this may result in

severe injury due to falling,

product breakage or collapse etc.

Electrocution / Electrical Shock

Hazard - Outdoor

High voltage or high current

electricity may be present or

required by the product. Do NOT

use in rain, damp, or wet

conditions. Electrical shock can

be fatal.

Electrocution / Electrical Shock

Hazard - Disconnect

High voltage or high current

electricity may be present or

required by the product. Always

disconnect the product from the

electrical supply before handling

the product, adjusting,

maintenance etc.

Power Line Electrocution

Hazard

High voltage / high current power

lines may be present. Use

extreme caution to avoid contact

or interference with power lines.

Electrical shock can be fatal.

"Kick-Back" Hazard

High level of "kick-back" hazard

that can cause the machine to

suddenly rotate towards operator.

Kick-back injury can be fatal.

Winch Operator Position

Hazard

Do NOT stand between winch

and load. Do NOT use winch to

move people.

Winch Lift Hazard

Do NOT LIFT load vertically. Use

machine to PULL only.

Cable Hazard

Ensure that load bearing cable is

not kinked or knotted.

Winch Cable Hazard

Ensure that there is a minimum

number of cable coils on

winching mechanism.

Winch Hook Hazard

Carry hook to load – do NOT

throw or run.

Flash / Blinding Hazard

Wear appropriate eye protection

for welding. Direct exposure to

weld arcs may cause permanent

eye injury.

Laser Hazard

Laser may be in use – do NOT

look directly at laser or allow

others to.

Multi-Function Workbench

Table of Contents

Safety ............................................................................................................................................................. 2

Safety Symbols ........................................................................................................................................................... 5

Parts Identification ....................................................................................................................................... 8

Assembly ..................................................................................................................................................... 10

Maintenance and Servicing ....................................................................................................................... 22

Cleaning, Maintenance, and Lubrication .................................................................................................................. 22

Replacing the Light Bulb ........................................................................................................................................... 22

Specifications ............................................................................................................................................. 23

Multi-Function Workbench

Parts Identification

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Multi-Function Workbench

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND

ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE

MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO

THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE

OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER

AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS

SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER.

THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE

ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER

INSTALLATION OF REPLACEMENT PARTS THERETO.

No.

Name

Qty.

No.

Name

Qty.

1

Front post

2

16F

Front shelf beam

1

2

Back post

2

16B

Back shelf beam

1

3

Rubber foot

4

17L

Left shelf beam

1

4

Side beam

3

17R

Right shelf beam

1

5

Bottom beam

2

18

Pegboard

1

6

Top beam

2

19

Bench top

1

7F

Front drawer bracket

1

20

Bottom shelf

1

7B

Back drawer bracket

1

21

Top shelf

1

8

Middle drawer mount

1

22

Power strip (not shown)

1

9L

Left drawer mount

1

23

Light fixture (not shown)

1

9R

Right drawer mount

1

A

Bolt (M4x10), washer, nut

8

10L

Left drawer panel

2

B

Bolt (M6x10), washer, nut

78

10R

Right drawer panel

2

C

Bolt (M6x16), washer, nut

13

11

Front drawer panel

2

D

Bolt (M5x25), washer, nut

12

Back drawer panel

2

E

Screw (ST4x9.5)

4

13

Drawer bottom

2

F

U bracket

2

14

Drawer handle

2

G

Bolt (M4x16)

2

15

Back upper post

2

Some parts are listed and shown for illustration purposes only and are not available individually as replacement

parts.

Spare parts available

for purchase, scan QR

code below:

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Multi-Function Workbench

Assembly

IMPORTANT! Read the SAFETY INFORMATION section at the beginning of this document

including all text under subheadings therein before setting up or use of this product.

NOTE: Unless stated otherwise, all connections are made using Bolts, Washers and Nuts (B). Finger-

tighten all connections until assembly is done. Assemble the Workbench on a flat, level, hard surface.

1. Attach Side Beams (4) to Front (1) and Back Posts (2).

2. Attach Rubber Feet (3) to the bottom of each post.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Multi-Function Workbench

3. Attach Bottom Beams (5) to Front and Back Posts.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Multi-Function Workbench

4. Attach Side Beam (4) to the top 2 holes on Front Posts and the middle 2 holes on Back Posts.

NOTE: Side Beam with Power Strip Opening can be attached to either the right or left side.

5. Attach Power Strip (22) to Side Beam with Power Strip Opening using U Brackets (F) and Screws (E).

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Multi-Function Workbench

6. Attach Top Beams (6) to the top 2 holes on Front Posts and the middle 2 holes on Back Posts.

NOTE: Make sure the Front Top Beam carries the Warning Label and is right-side up.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Multi-Function Workbench

7. Attach Front (7F) and Back (7B) Drawer Brackets to Top Beams.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Multi-Function Workbench

8. Attach Middle Drawer Mount (8) to Front and Back Drawer Brackets.

9. Attach Left (9L) and Right (9R) Drawer Mounts to Front and Back Posts. Tighten hardware.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Multi-Function Workbench

10. Attach Drawer Handle (14) to the Front Drawer Panel (11) using Bolts, Washers and Nuts (A). Repeat for

second Front Drawer Panel. Tighten hardware.

11. Lay Drawer Bottom (13) down on a flat surface. Attach Right (10R) and Left (10L) Drawer Panels to the

Front and Back (12) Drawer Panels. Repeat for second Drawer.

12. Install the Drawers, making sure the runners on the Drawers are level with the Drawer Mounts.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Multi-Function Workbench

13. Attach left and right Back Upper Posts (15) to left and right Back Posts.

14. Attach Back Shelf Beam (16B) to Back Upper Posts.

15. Attach Left Shelf Beam (17L) and Right Shelf Beam (17R) to back Shelf Beam.

16. Attach Front Shelf Beam (16F) to Left and Right Shelf Beams.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Multi-Function Workbench

17. Attach Pegboard (18) to Back Upper Posts and Middle Drawer Mount using Bolts, Washers and Nuts (C).

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Multi-Function Workbench

18. Attach Bench Top (19) to Side Beams and Bottom Shelf (20) to Lower Side Beams using Bolts, Washers

and Nuts (D).

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Multi-Function Workbench

19. Attach Top Shelf (21) to Shelf Beams using Bolts, Washers and Nuts (D).

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Multi-Function Workbench

20. Attach Light Fixture (23) to the underside of the Top Shelf using Bolts (G).

a. Insert a Bolt through each Light Fixture Clip.

b. Thread Bolts through the holes on the underside of the Top Shelf.

c. Push Light Fixture up into the Clips.

21. Attach the Light Fixture power cord to the receptacle at the end of the fixture. It will only connect one way.

Route the cord through the hole in the Pegboard.

NOTE: Make sure all Shelves are level. Then, tighten all Bolts and Screws securely.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Multi-Function Workbench

Maintenance and Servicing

WARNING! Procedures not specifically explained in this manual must be performed only by a

qualified technician.

TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Make sure that the Trigger is in the

off‑position and unplug the tool from its electrical outlet before performing any procedure in this

section.

TO PREVENT SERIOUS INJURY FROM TOOL FAILURE: Do not use damaged equipment. If abnormal

noise or vibration occurs, have the problem corrected before further use.

Cleaning, Maintenance, and Lubrication

•

BEFORE EACH USE, inspect the general condition of the Workbench. Check for:

− loose hardware,

− misalignment or binding of moving parts,

− damaged cord/electrical wiring,

− cracked or broken parts, and

− any other condition that may affect its safe operation.

•

AFTER USE, wipe external surfaces with clean cloth.

Replacing the Light Bulb

The Light Fixture has a semitransparent cover over the bulb.

1. Allow Bulb to cool completely, then gently pull straight down at both ends of the cover and set aside.

2. Remove the Bulb by rotating it 90º, rolling in a forward or backward direction and dropping the Bulb straight

down.

3. With the prongs on either end of the Bulb vertically aligned, fit the new bulb up into the slots at the right and

left fixture receptacles.

4. Rotate the Bulb 90º again to seat the bulb. Replace the cover.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Multi-Function Workbench

Specifications

Frame material

Steel

Workbench

Particle board

Coating

Enamel

Total load capacity

250kg

Work light

LED 7W

Input voltage

240V AC

Power cord length

150cm

Power Plug

Australian Standard

Note: Assembly Required

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Some experts believe that the incorrect or prolonged use of almost any

product may cause serious injury or death. To help reduce your risk of

serious injury or death, refer to the information below. For more information,

see www.datastreamserver.com/safety

◼

Consult all documentation, packaging,

and product labelling before use. Note

that some products feature

documentation available online. It is

recommended to print and retain the

documentation.

◼

Before each use, check the product for

loose/broken/damaged/missing parts,

wear, or leaks (if applicable). Never use a

product with

loose/broken/damaged/missing parts,

wear, or leaks.

◼

Products must be inspected and serviced

(if applicable) by a qualified technician

every 6 months. This is based on

average residential use by persons of

average size and strength, and on a

property of average metropolitan size.

Use beyond these recommendations may

require more frequent

inspections/servicing.

◼

Ensure that all users of the product have

completed a suitable industry recognised

training course before being allowed

access to the product.

◼

The product has been supplied by a general merchandise

retailer that may not be familiar with your specific

application or description of application. Be sure to attain

third-party approval from a qualified specialist for your

application before use, regardless of any assurances from

the retailer or its representatives.

◼

This product is not intended for use where fail-safe

operation is required. As with any product (for example,

automobile, computer, toaster), there is the possibility of

technical issues that may require the repair or

replacement of parts, or the product itself. If the possibility

of such failure and the associated time it may take to

rectify could in any way inconvenience the user, business,

or employee, or financially affect the user, business, or

employee, then the product is not suitable for your

requirements. This product is not intended for use where

incorrect operation or a failure of any kind, including but

not limited to, a condition requiring product return,

replacement, parts replacement, or service by a

technician may cause financial loss, loss of employee

time or an inconvenience requiring compensation.

◼

If this product has been purchased in error when

considering the information presented here, contact the

retailer directly for details of their returns policy, if

required.

ideas, diagrams, or images may be reproduced or transmitted in any form or by any means, electronic or

mechanical, including photocopying, scanning, or recording, or any information storage and retrieval system,

without express permission or consent from the publisher.

BAUMR-AG TOLWBNBMRA6XL Steel Workbench LED Worklight for Garage Workshop

Product's Documents

Product manual

Specifications

BAUMR-AG TOLWBNBMRA6XL Questions and Answers