Oregon CHNSAWBMRASW3 Baumr-AG 20V 10" Bar Cordless Chainsaw User Manual

THE BATTERY MAY HAVE SOME CHARGE ON ARRIVAL, IT IS IMPORTANT

HOWEVER THAT THE BATTERY IS CHARGED PRIOR TO USE.

User Manual

[Revision 8.0 October 2023]

READ THIS MANUAL CAREFULLY BEFORE USE – FAILURE TO DO SO MAY RESULT IN INJURY, PROPERTY DAMAGE

AND MAY VOID WARRANTY. • KEEP THIS MANUAL FOR FUTURE REFERENCE. • Products covered by this manual may

vary in appearance, assembly, inclusions, specifications, description, and packaging.

Chainsaw Kits - SW3 and SW4

Safety

Safety messages are designed to alert you to possible dangers or hazards that could cause death, injury or

equipment or property damage if not understood or followed. Safety messages have the following symbols:

You WILL be KILLED or

SERIOUSLY INJURED if you do

not follow instructions.

You CAN be KILLED or

SERIOUSLY INJURED if you do

not follow instructions.

You CAN be INJURED if you do

not follow instructions or equipment

damage may occur.

It is vital that you read and understand this

user manual before using the product,

including safety warnings, and any assembly

and operating instructions. Keep the manual

for future reference.

Safety precautions and recommendations

detailed here must be fully understood and

followed to reduce the risk of injury, fire,

explosion, electrical hazard, and/or property

damage.

Safety information presented here is generic

in nature – some advice may not be

applicable to every product. The term

"equipment" refers to the product, be it

electrical mains powered, battery powered or

combustion engine powered.

• Before Use - If you are not familiar with the

safe operation/handling of the equipment or

are in any way unsure of any aspect of

suitability or correct use for your

application, you should complete training

conducted by a person or organization

qualified in safe use and operation of this

equipment, including fuel/electrical handling

and safety.

• Do NOT operate the equipment in

flammable or explosive environments, such

as in the presence of flammable liquids,

gases or dust. The equipment may create

sparks or heat that may ignite flammable

substances.

• Keep clear of moving parts.

• Equipment may be a potential source of

electric shock or injury if misused.

• Do NOT operate the equipment if it is

damaged, malfunctioning or is in an

excessively worn state.

• Do NOT allow others to use the equipment

unless they have read this manual and are

adequately trained.

• Keep packaging away from children - risk

of suffocation! Operators must use the

equipment correctly. When using the

equipment, consider conditions and pay

due care to persons and property.

General Work Area Safety

• Work areas should be clean and well it.

• Do not operate the equipment if

bystanders, animals etc are within

operating range of the equipment or the

general work area.

• If devices are provided for connecting dust

extraction / collection facilities, ensure

these are connected and used properly.

Dust collection can reduce dust-related

hazards.

General Personal Safety

• Wear appropriate protective equipment

when operating, servicing, or when in the

operating area of the equipment to help

protect from eye and ear injury, poisoning,

burns, cutting and crush injuries. Protective

equipment such as safety goggles,

respirators, non-slip safety footwear, hard

hat, hearing protection etc should be used

for appropriate equipment / conditions.

Other people nearby should also wear

appropriate personal protective equipment.

Do not wear loose clothing or jewellery,

which can be caught in moving parts. Keep

hair and clothing away from the equipment.

• Stay alert and use common sense when

operating the equipment. Do not over-

reach. Always maintain secure footing and

balance.

• Do not use the equipment if tired or under

the influence of drugs, alcohol or

medication.

• This equipment is not intended for use by

persons with reduced physical, sensory or

mental capabilities.

General Fuel Safety

• Petrol/fuel/gasoline is extremely flammable

– keep clear of naked flames or other

ignition sources.

• Do not spill fuel. If you spill fuel, wipe it off

the equipment immediately – if fuel gets on

your clothing, change clothing.

• Do NOT smoke near fuel or when

refuelling.

• Always shut off the engine before

refuelling.

• Do NOT refuel a hot engine.

• Open the fuel cap carefully to allow any

pressure build-up in the tank to release

slowly.

• Always refuel in well ventilated areas.

• Always check for fuel leakage. If fuel

leakage is found, do not start or run the

engine until all leaks are fixed.

General Carbon-Monoxide Safety

• Using a combustion engine indoors CAN

KILL IN MINUTES. Engine exhaust

contains carbon-monoxide – a poison you

cannot smell or see.

• Use combustion engines OUTSIDE only,

and far away from windows, doors and

vents.

General Equipment Use and Care

• The equipment is designed for domestic

use only.

• Handle the equipment safely and carefully.

• Before use, inspect the equipment for

misalignment or binding of moving parts,

loose components, damage or any other

condition that may affect its operation. If

damaged, have the equipment repaired by

an authorised service centre or technician

before use.

• Prevent unintentional starting of the

equipment - ensure equipment and power

switches are in the OFF position before

connecting or moving equipment. Do not

carry equipment with hands or fingers

touching any controls. Remove any tools or

other items that are not a part of the

equipment from it before starting or

switching on.

• Do not force the equipment. Use the

correct equipment for your application.

Equipment will perform better and be safer

when used within its design and usage

parameters.

• Use the equipment and accessories etc. in

accordance with these instructions,

considering working conditions and the

work to be performed. Using the equipment

for operations different from those intended

could result in hazardous situations.

• Always keep equipment components

(engines, hoses, handles, controls, frames,

housings, guards etc) and accessories

(cutting tools, nozzles, bits etc) properly

maintained. Keep the equipment clean and,

where applicable, properly lubricated.

• Store the equipment out of reach of

children or untrained persons. To avoid

burns or fire hazards, let the equipment

cool completely before transporting or

storing. Never place or store the equipment

near flammable materials, combustible

gases or liquids etc.

• The equipment is not weather-proof, and

should not be stored in direct sunlight, at

high ambient temperatures or locations that

are damp or humid.

• Do not clean equipment with solvents,

flammable liquids or harsh abrasives.

• For specific equipment safety use and care,

see Equipment Safety.

Chainsaw Kits - SW3 and SW4

General Electrical Safety

• Inspect electrical equipment, extension

cords, power bars, and electrical fittings for

damage or wear before each use. Repair or

replace damaged equipment immediately.

• Ensure all power sources conform to

equipment voltage requirements and are

disconnected before connecting or

disconnecting equipment.

• When wiring electrically powered

equipment, follow all electrical and safety

codes.

• Wherever possible, use a residual current

device (RCD).

• High voltage / high current power lines may

be present. Use extreme caution to avoid

contact or interference with power lines.

Electrical shock can be fatal.

General Electrical Safety

• Electrically grounded equipment must have

an approved cord and plug and be

connected to a grounded electrical outlet.

• Do NOT bypass the ON/OFF switch and

operate equipment by connecting and

disconnecting the electrical cord.

• Do NOT use equipment that has exposed

wiring, damaged switches, covers or

guards.

• Do NOT use electrical equipment in wet

conditions or in damp locations.

• Do NOT use electrical cords to lift, move or

carry equipment.

• Do NOT coil or knot electrical cords, and

ensure electrical cords are not trip hazards.

General Service Information

• The equipment must be serviced or

repaired at authorised service centres by

qualified personnel only.

• Replacement parts must be original

equipment manufacturer (OEM) to ensure

equipment safety is maintained.

• Do NOT attempt any maintenance or repair

work not described in this manual.

• After use, the equipment and components

may still be hot – allow the equipment to

cool and disconnect spark plugs and/or

electrical power sources and/or batteries

from it before adjusting, changing

accessories or performing repair or

maintenance.

• Do NOT adjust while the equipment is

running.

• Perform service related activities in suitable

conditions, such as a workshop.

• Replace worn, damaged or missing

warning/safety labels immediately.

Intended Use

• This device may only be used with the approved original cutting chain for sawing wood.

• This product is not intended for commercial use. Generally acknowledged accident prevention regulations and enclosed safety instructions must

be observed.

• Only perform work described in these instructions for use. Any other use is improper. The manufacturer will not assume responsibility for damage

resulting from such use.

General Safety Instructions

• To operate this device safely, the user must have read and understood these instructions for use before using the device for the first time.

• If you sell or pass the device on, you must also hand over these operating instructions.

General Power tool Safety Warnings

• WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock,

fire and/or serious injury.

• Save all warnings and instructions for future reference. The term power tool in the warnings refers to your mains operated (corded) power tool or

battery operated (cordless) power tool.

Work Area Safety

• Keep work area clean and well lit. Cluttered and dark areas invite accidents.

• Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

• Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

Electrical safety

• Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools.

Unmodified plugs and matching outlets will reduce risk of electric shock.

• Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

• Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.

• Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or

moving parts. Damaged or entangled cords increase the risk of electric shock.

• When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of

electric shock.

• If operating a power tools in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the

risk of electric shock.

Personal Safety

• Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under

the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.

• Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or

hearing protection used for appropriate conditions will reduce personal injuries.

• Prevent unintentional starting. Ensure the switch is in the off position before connecting to power source and/or battery pack, picking up or

carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.

Chainsaw Kits - SW3 and SW4

• Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may

result in personal injury.

• Do not overreach. Always keep proper footing and balance. This enables better control of the power tool in unexpected situations.

• Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewellery or

long hair can be caught in moving parts.

• If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of these

devices can reduce dust-related hazards.

Power Tool Use and Care

• Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for

which it was designed.

• Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must

be repaired.

• Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or

storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.

• Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the

power tool. Power tools are dangerous in the hands of untrained users.

• Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power

tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.

• Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

• Use the power tool, accessories, and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work

to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.

Battery Tool Use and Care

• Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire

when used with another battery pack.

• Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.

• When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects,

that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.

• Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts

eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.

• Do not open the rechargeable battery. The rechargeable battery can be damaged by improper handling.

• Do not expose the rechargeable battery to heat, fire, water and humidity. There is a danger of explosion.

• Vapours may escape in case of damage or improper use of the rechargeable battery. Provide good ventilation and seek medical assistance in

case any symptoms occur. The vapours can irritate your respiratory tract and cause illness.

• Never attempt to charge non-rechargeable batteries. There is a danger of fire and explosion.

• The rechargeable battery may only be used in conjunction with this electrical tool. Other electrical tools can overload and hence damage the

rechargeable battery.

• Only chargers approved by the manufacturer with the values stated on the type plate of the rechargeable battery may be used. The use of

deviating chargers can pose the risk of injuries and material damage caused by exploding batteries.

Safety Information for Chargers

• Keep the charger away from rain and wet. The risk of electric shock increases if water penetrates a charging device.

• Keep the charging device clean. Soiling involves the danger of an electric shock.

• Check the charging device, cable, and plug before each use. Do not use the charging device if you detect any damage.

• Do not open the charging device yourself and only have it repaired by qualified professionals and only with original spare parts. Damaged

charging devices, cables and plugs increase the risk of electric shock.

• Do not use the charging device on easily flammables items (e.g. paper, textiles etc.) or in combustible atmospheres. There is a danger of fire due

to the heating of the charging device during the charging process.

• Supervise children and make sure that they do not play with the charger. Children and persons with mental or physical restrictions may only use

the charger under supervision or after having been instructed how to use it. Careful instruction reduces the risk of incorrect operation and injuries.

Service

Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool

is maintained.

Chain Saw Safety Warnings

• Keep all parts of the body away from the saw chain when the chain saw is operating. Before you start the chain saw, make sure the saw chain is

not contacting anything. A moment of inattention while operating chain saws may cause entanglement of your clothing or body with the saw

chain.

• Always hold the chain saw with your right hand on the rear handle and your left hand on the front handle. Holding the chain saw with a reversed

hand configuration increases the risk of personal injury and should never be done.

• Hold the power tool by insulated gripping surfaces only, because the saw chain may contact hidden wiring. Saw chains contacting a “live” wire

may make exposed metal parts of the power tool “live” and could give the operator an electric shock.

• Hold the power tool by insulated gripping surfaces only, because the saw chain may contact hidden wiring or its own cord. Saw chains contacting

a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.

Chainsaw Kits - SW3 and SW4

• Wear safety glasses and hearing protection. Further protective equipment for head, hands, legs and feet is recommended. Adequate protective

clothing will reduce personal injury by flying debris or accidental contact with the saw chain.

• Do not operate a chain saw in a tree. Operation of a chain saw while up in a tree may result in personal injury.

• Always keep proper footing and operate the chain saw only when standing on fixed, secure and level surface. Slippery or unstable surfaces such

as ladders may cause a loss of balance or control of the chain saw.

• When cutting a limb that is under tension be alert for spring back. When the tension in the wood fibres is released the spring-loaded limb may

strike the operator and/or throw the chain saw out of control.

• Use extreme caution when cutting brush and saplings. The slender material may catch the saw chain and be whipped toward you or pull you off

balance.

• Carry the chain saw by the front handle with the chain saw switched off and away from your body. When transporting or storing the chain saw

always fit the guide bar cover. Proper handling of the chain saw will reduce the likelihood of accidental contact with the moving saw chain.

• Follow instructions for lubricating, chain tensioning and changing accessories. Improperly tensioned or lubricated chain may either break or

increase the chance for kickback.

• Keep handles dry, clean, and free from oil and grease. Greasy, oily handles are slippery causing loss of control.

• Cut wood only. Do not use chain saw for purposes not intended. For example: do not use chain saw for cutting plastic, masonry, or non-wood

building materials. Use of the chain saw for operations different than intended could result in a hazardous situation.

• Before starting the device, you must ensure that the chain is free from foreign objects.

• Always cut at full motor power and keep the speed constant.

Causes and Operator Prevention of Kickback

Kickback may occur when the nose or tip of the guide bar touches an object, or when the wood closes in and pinches the saw chain in the cut.

Tip contact in some cases may cause a sudden reverse reaction, kicking the guide bar up and back towards the operator.

Pinching the saw chain along the top of the guide bar may push the guide bar rapidly back towards the operator.

Either of these reactions may cause you to lose control of the saw which could result in serious personal injury. Do not rely exclusively upon the

safety devices built into your saw.

As a chain saw user, you should take several steps to keep your cutting jobs free from accident or injury.

Kickback is the result of tool misuse and/or incorrect operating procedures or conditions and can be avoided by taking proper precautions as given

below:

• Maintain a firm grip, with thumbs and fingers encircling the chain saw handles, with both hands on the saw and position your body and arm to

allow you to resist kickback forces. Kickback forces can be controlled by the operator, if proper precautions are taken. Do not let go of the chain

saw.

• Do not overreach and do not cut above shoulder height. This helps prevent unintended tip contact and enables better control of the chain saw in

unexpected situations.

• Only use replacement bars and chains specified by the manufacturer. Incorrect replacement bars and chains may cause chain breakage and/or

kickback.

• Follow the manufacturer’s sharpening and maintenance instructions for the saw chain. Decreasing the depth gauge height can lead to increased

kickback.

Additional Safety Information

• It is recommended that the user is instructed by a qualified specialist about the operation of the chain saw and the use of safety equipment based

on practical examples prior to first commissioning.

• This product is not intended to be used by persons (including children) or who are limited in their physical, sensory, or mental capacities or who

lack experience and/or knowledge of the product.

• Children should be supervised to ensure that they do not use the product as a toy.

• Children and adolescents are not allowed to operate the chain saw. The same applies to persons who are not or not well enough acquainted with

the chain saw.

• The operating instructions should always be within easy reach.

• Persons suffering from fatigue or who are not physically fit must not operate the chain saw.

• Keep the handles dry and free from grease. Slippery handles can cause accidents.

• Keep a firm hold of the electrical tool with both hands while working and make sure you are standing firmly. The electrical tool is more safely

guided using two hands.

• Do not leave tools, objects or cable laying around in the vicinity of the device. If you stumble, you may injure yourself on the power tool.

• Make sure that all safety facilities and handles are mounted when using the product.

• Never attempt to operate an incompletely mounted product or a product with impermissible modifications.

• Wait until the electrical tool has come to a standstill before putting it down.

• Do not use any accessory that has not been provided and recommended by the manufacturer specially for this electrical tool. Just because the

accessories can be fixed on your electrical tool, no secured use is ensured.

• Remember that moving parts may also be located behind ventilation and venting slots.

• The fuse must be a residual current circuit-breaker with a measured residual current of no more than 30 mA.

• Lay out the cable such that it cannot become caught in branches or similar during sawing.

• Beginners should at least first practice cutting round wood logs positioned on a saw block or on a frame.

• If the power supply cable is damaged, it must be replaced with a specially equipped cable, which is available from the customer service

organisation.

Chainsaw Kits - SW3 and SW4

• Changing of the plug or the power supply cable must always be carried out by the manufacturer of the electric tool or by a manufacturer's service.

Risks Caused by Vibrations

CAUTION! Risk of injury due to vibrations! Vibrations may, for persons with circulation problems, cause damage to blood vessels and/or

nerves. If you notice any of the following symptoms, stop working immediately and consult a doctor. Numbness of body parts, loss of

sense of feeling, itching, pins and needles, pain, changes in skin colour.

The vibration values specified in the technical data represent the main uses of the device. The actual existing vibrations during use may deviate

from these because of the following factors:

• Incorrect use of the product.

• Unsuitable tools inserted.

• Unsuitable material.

• Insufficient maintenance.

You can reduce the risks considerably by following the tips below:

• Maintain the device in accordance with the instructions in the operating instructions.

• Avoid working at low temperatures.

• When it is cold, make sure your body and your hands are kept warm.

• Take regular breaks and move your hands at the same time to promote circulation.

Personal Protective Equipment/Sensible Clothing

When cutting, wear the following protective equipment:

• Eye protection: wrap-around goggles/protective visor on the helmet

• Ear protection: earplugs/earmuffs

• Head protection: safety helmet with visor

• Foot protection: safety shoes with gripping soles, steel caps and leg protection

• Hand protection: protective chainsaw gloves

• Clothing: safety overalls (cut-proof), Safety jacket (cut-proof)

Avoid with your clothing that you get caught on something:

• Wear only close-fitting clothing!

• Do not wear any jewellery!

• If you have long hair, wear a hair net!

Chainsaw Kits - SW3 and SW4

Safety Symbols

The product may have safety warning labels attached to it, explained below. Understand the symbols on your

product and their meanings. If any stickers become unreadable, unattached etc., replace them.

Flammable Material Hazard

Flammable liquids, gases or

substances etc may present.

Avoid ignition sources and open

flames. Danger of fire.

Read User Manual

Read and fully understand

product safety warnings,

operation, procedures etc before

using the product.

Use Hand Protection

Wear appropriate hand protection

and take due care as the product

or use of the product may present

hand hazards.

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be fatal.

Electrocution / Electrical Shock

Hazard

High voltage or high current

electricity may be present or

required by the product. Take

due care when handling electrical

products, cables, plugs and

leads. Electrical shock can be

fatal.

Toxic Fumes / Dust Hazard

Using the product or by-products

from use may produce fumes,

smoke or particles that could be

harmful if inhaled. Wear

appropriate breathing protection

and have adequate ventilation.

Explosive Material Hazard

Combustible liquids, gases or

substances etc may be present.

Avoid ignition sources and open

flames. Danger of explosion.

Cutting / Amputation Hazard

The product may have blades,

edges or mechanical devices that

can cause severe cut injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Crush Hazard

The product may have blades,

edges or mechanical devices that

can cause severe crush injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Single Operator Only

The product must be operated by

a single person only. More than

one person operating the product

may introduce additional hazards.

Use Face Protection

Wear appropriate full-face

protection and take due care as

the product or use of the product

may present face and eye

hazards.

Use Foot Protection

Wear appropriate foot protection

and take due care as the product

or use of the product may present

foot hazards.

Use Eye / Ear / Head Protection

Wear appropriate eye and / or

ear and / or head protection and

take due care as the product or

use of the product may present

eye, hearing and head hazards.

Running Hazard

Do not run on or near the product

as doing so may present a fall

hazard.

Diving Hazard

Do not dive into the product as

doing so may present a neck /

head injury hazard.

Adult Supervision Required

Always supervise children and

other users of a product to

prevent drowning or injury.

Skin Penetration / Puncture

Hazard

The product may produce

pressure, emit liquids or objects

that can cause severe injury to

fingers, limbs, blood etc. Take

due care when handling and

using the product.

Hot Surface Hazard

Be aware that the product may

produce high temperatures and

hot surfaces that can cause burn

injuries.

Flying Debris Hazard

Be aware that the product or use

of the product may present

hazards produced by flying

debris. Wear appropriate clothing

and protective devices.

Moving Parts Hazard

Be aware that the product

contains or uses mechanical

devices that move or rotate.

Always wait for moving parts to

stop fully before handling the

product, adjusting, maintenance

etc.

Chainsaw Kits - SW3 and SW4

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be fatal.

Pull Hazard

Be aware that the product

contains or uses mechanical

devices that can pull in objects

and can cause severe injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Slope / Fall Injury Hazard

Be aware that using the product

on sloping surfaces or in slippery

conditions may present additional

dangers from falls and contact

with blades, moving parts, hot

surfaces etc.

"Slam Dunk" Warning

Do NOT attempt "slam dunk"

manoeuvres as this may result in

severe injury due to falling,

product breakage or collapse etc.

Electrocution / Electrical Shock

Hazard - Outdoor

High voltage or high current

electricity may be present or

required by the product. Do NOT

use in rain, damp or wet

conditions. Electrical shock can

be fatal.

Electrocution / Electrical Shock

Hazard - Disconnect

High voltage or high current

electricity may be present or

required by the product. Always

disconnect the product from the

electrical supply before handling

the product, adjusting,

maintenance etc.

Power Line Electrocution

Hazard

High voltage / high current power

lines may be present. Use

extreme caution to avoid contact

or interference with power lines.

Electrical shock can be fatal.

"Kick-Back" Hazard

High level of "kick-back" hazard

that can cause the machine to

suddenly rotate towards operator.

Kick-back injury can be fatal.

Winch Operator Position

Hazard

Do NOT stand between winch

and load. Do NOT use winch to

move people.

Winch Lift Hazard

Do NOT LIFT load vertically. Use

machine to PULL only.

Cable Hazard

Ensure that load bearing cable is

not kinked or knotted.

Winch Cable Hazard

Ensure that there is a minimum

number of cable coils on

winching mechanism.

Winch Hook Hazard

Carry hook to load – do NOT

throw or run.

Flash / Blinding Hazard

Wear appropriate eye protection

for welding. Direct exposure to

weld arcs may cause permanent

eye injury.

Laser Hazard

Laser may be in use – do NOT

look directly at laser or allow

others to.

Chainsaw Kits - SW3 and SW4

Table of Contents

Safety ............................................................................................................................................................. 2

Safety Symbols ........................................................................................................................................................... 7

Parts Identification ..................................................................................................................................... 11

Parts List ..................................................................................................................................................... 13

Assembly ..................................................................................................................................................... 14

Assembling the Saw Rail and Saw Chain ................................................................................................................ 14

Tightening the Chain................................................................................................................................................. 15

Letting the Saw Chain Run In ................................................................................................................................... 15

Checking the Tensioning of the Saw Chain ............................................................................................................. 15

Checking the Chain Lubrication ................................................................................................................................ 16

Checking the Chain Brake ........................................................................................................................................ 16

Filling Up with Saw Chain Oil ................................................................................................................................... 16

Operation ..................................................................................................................................................... 17

Safety Equipment ..................................................................................................................................................... 17

Chain Catcher .................................................................................................................................................... 17

Rear Hand Guard ............................................................................................................................................... 17

Charging the Battery Pack ........................................................................................................................................ 18

Checking the Remaining Capacity of the Battery ..................................................................................................... 18

Checks Before Starting ............................................................................................................................................. 19

Switching ON/OFF .................................................................................................................................................... 19

Operating the Chainsaw ........................................................................................................................................... 20

Correct Posture .................................................................................................................................................. 20

How to Saw Correctly ............................................................................................................................................... 20

Kickback Risks .......................................................................................................................................................... 20

Basic Techniques ..................................................................................................................................................... 21

Before Each Use ................................................................................................................................................ 21

Pulling Sawing .................................................................................................................................................... 21

Pushing Sawing ................................................................................................................................................. 22

Cutting Down Trees ........................................................................................................................................... 23

Trunks Lying Flat on the Ground ....................................................................................................................... 23

Propped-Up Trunks ............................................................................................................................................ 24

Removing Branches ........................................................................................................................................... 24

Lithium Battery Care and Maintenance .................................................................................................... 25

Top 3 Battery Care Requirements ............................................................................................................................ 25

Maintenance ................................................................................................................................................ 27

Cleaning the Device .................................................................................................................................................. 27

Cleaning the Oil Guide Groove of the Saw Rail ....................................................................................................... 27

Re-Tensioning the Saw Chain .................................................................................................................................. 27

Chainsaw Kits - SW3 and SW4

Sharpening the Saw Chain ....................................................................................................................................... 27

Storage and Transportation ....................................................................................................................... 28

Storage ..................................................................................................................................................................... 28

Transportation ........................................................................................................................................................... 28

Troubleshooting ......................................................................................................................................... 29

Specifications ............................................................................................................................................. 30

SW3 .......................................................................................................................................................................... 30

SW4 .......................................................................................................................................................................... 31

Chainsaw Kits - SW3 and SW4

Parts Identification

NOTE: The actual appearance of your product may differ from the illustrations.

1

2

3

4

5

6

7

8

9

10

14

13

11

12

15

16

17

18

19

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Chainsaw Kits - SW3 and SW4

No. Name No. Name

1 Rear handle 11 Safety lock

2 Fill opening for chain oil (tank cover) 12 ON-OFF switch

3 Front hand guard (trigger for chain brake) 13 Battery pack

4

Saw chain

14

Front handle

5

Saw rail

15

Display for remaining capacity

6

Chain tensioning screw

16

Push button for capacity display

7

Quick locking device (for saw rail)

17

Locking button

8

Chain wheel guard

18

Control lights

9 Inspection glass for oil level 19 Battery charger

10 Rear hand guard

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Chainsaw Kits - SW3 and SW4

Parts List

Spare parts available for purchase, scan QR codes below:

QR Code SKU

CHNSAWBMRASW3

CHNSAWBMRASW4

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Chainsaw Kits - SW3 and SW4

Assembly

DANGER! Risk of injury during operation! Improperly mounted parts can cause severe and

even fatal injuries when using the device! This device may only be commissioned if all parts are

mounted completely and tightly and no part is damaged! •read the whole chapter before you assemble the parts!

• Assemble the parts carefully and completely. • Use tools when their use is suggested.

CAUTION! Risk of injuries due to cuts! The teeth of the saw chain are very sharp! Protective gloves must be

worn for all work on the chain.

WARNING! Risk of injury! An improperly mounted saw chain causes uncontrolled cutting behaviour of the

device! When assembling the chain, heed the prescribed running direction!

Assembling the Saw Rail and Saw Chain

1. Release the chain brake (3) (move the hand guard back and engage it).

2. Unlock and loosen the quick-locking device (7) and remove the chain wheel guard (8).

NOTE: When attaching the chain, heed the correct position of the guide groove (saw rail).

3. Place the sawing chain onto the chain wheel. Pay attention to the chain’s correct direction of rotation: the

direction in which the arrow points on the chain must match the direction marked on the chain

wheel.

4. Attach the saw rail and push it towards the chain wheel.

5. Insert the sawing chain into the guiding groove of the saw rail.

6. Route the sawing chain around the saw rail. Ensure the correct location inside the guiding groove.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Chainsaw Kits - SW3 and SW4

7. Attach the chain wheel cover. The chain dowel spin must engage in the hole of the saw rail.

8. Now gently tighten the quick locking device (7).

Tightening the Chain

1. Slightly lift the tip of the saw rail.

2. Check if the sawing chain runs smoothly by turning it manually.

3. Turn the tensioning screw (6) until the chain lies on the underside of the saw rail.

4. Tighten and lock quick locking device (7).

Letting the Saw Chain Run In

During the run-in time, re-tension the saw chain and rail after a maximum of 5 cuts.

Checking the Tensioning of the Saw Chain

The saw chain is tensioned correctly if it lies close against the underside of the saw rail and can be moved easily

by hand. Readjust tension of the saw chain when necessary.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Chainsaw Kits - SW3 and SW4

Checking the Chain Lubrication

The device may not be used without sufficient chain lubrication. Insufficient lubrication reduces the service life of

the device.

1. Check the oil quantity in the tank.

2. Start the device.

3. Hold the running saw chain approx. 15cm over a suitable surface for a time (15 s). If there is sufficient chain

lubrication, the oil spraying from the saw chain will form a slight trail.

Checking the Chain Brake

The chain brake ensures immediate blocking of the saw chain in case of a kickback. Before using the device,

ensure that it is functioning correctly.

1. Set device on the ground.

2. Start the device.

3. Tip the hand guard forwards. The chain must stop immediately.

4. If the chain brake is not working correctly, contact a service partner immediately.

Filling Up with Saw Chain Oil

NOTICE! Environmental damage! Since the saw chain oil can seep into the environment during operation,

biodegradable, vegetable-based saw chain oils should be used.

1. Lay device securely with the tank cover (2) upwards.

2. Before opening, clean the tank cover and the filler neck, if necessary.

3. Open flap and remove tank cover.

4. Carefully fill up the saw chain oil. Do not spill!

5. Read the oil level at the inspection glass (9). The oil stand must be placed between [MIN] and [MAX].

6. Attach tank cover and close flap.

7. If you have spilled any saw chain oil, be sure to wipe it up.

9

2

MAX

MIN

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Chainsaw Kits - SW3 and SW4

Operation

Safety Equipment

The device has several pieces of safety equipment which reduce the risk of injury when working:

Chain Catcher

The chain catcher serves to catch a torn saw chain or one which has jumped out of the guide. Through regular

maintenance of the saw rail and correct and regular tensioning of the saw chain, accidents of this type can be

prevented.

Rear Hand Guard

The rear hand guard serves to protect your hand against a jumped chain and disturbing branches and twigs.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Chainsaw Kits - SW3 and SW4

Charging the Battery Pack

WARNING! Risk of injury! Comply with all safety instructions when handling rechargeable

devices. NOTICE! Risk of damage to the unit! Do not allow the battery pack to deep discharge.

NOTE: If the battery is fully loaded, the charger automatically switches over to the maintenance charge function.

The battery pack must be charged prior to the first start-up.

1. Press the locking button (17) and remove the battery from the device.

2. Insert the battery pack into the charger.

3. Plug the charger into the power supply. The charging status is displayed by the control lights (18).

4. Insert the battery pack into the device and make sure it clicks into place correctly.

Checking the Remaining Capacity of the Battery

Press the Push button for capacity display (16). The remaining capacity of the battery is displayed by the control

lights (15).

17

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Chainsaw Kits - SW3 and SW4

Checks Before Starting

DANGER! Risk of injury! The device must only be put into operation if no faults are found. If any

part of the device is defective, it must be replaced before the next use.

Check the safety equipment and the safe condition of the device.

•

Check all parts for their firm fit.

•

Check whether there is any leakage.

•

Check whether there are visible defects: broken parts, cracks, etc.

•

Check the device for correct chain tensioning.

•

Check the function of the chain brake.

Switching ON/OFF

1. Hold the device securely with both hands.

2. The chain brake must be puled back.

3. Switching ON: Press switch-on safety lock (11) and ON/OFF switch (12) simultaneously.

4. Switching off: Release On-Off switch (12).

3

11

12

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Chainsaw Kits - SW3 and SW4

Operating the Chainsaw

NOTE: Before using the chainsaw, familiarize yourself sufficiently with the sawing technique for chainsaws. You

will find information about this in the trade literatures. We recommend that you attend suitable training sessions.

The notes here serve only as a complement!

Correct Posture

DANGER! Risk of injury! Never work on unstable surfaces! Never work above shoulder height!

Never work while standing on a ladder! Do not work bent too far forward! Only use the device

under favourable weather and site conditions!

1. Stand with both legs securely on the ground.

2. Heed obstacles in the work area.

3. While you are working, always hold the device fast with both hands!

Hold the device:

− With the left hand on the front handle.

− With the right hand on the rear handle.

− Balanced in a secure position.

How to Saw Correctly

DANGER! Risk of injury! Always switch the motor OFF before you put the device down!

1. Search the work area and remove objects which are in your way.

2. When you begin work, check the safety of the device (Checks Before Starting).

3. Take the device in both hands, as instructed.

Kickback Risks

DANGER! Risk of injury! When working

with the device, dangerous kickbacks

may occur! Severe or even fatal injuries can be the

result! Before beginning work with the device, the chain

brake must be checked to ensure that it is functioning

correctly.

Kickbacks occur if the upper edge or tip of the saw rail

contacts wood or other hard objects. The device is

thrown with high energy back and forth, which can

cause extremely severe injuries.

Avoid letting the area of the saw rail touch wood or other hard objects. To reduce the risk of injury in case of a

kickback, the device is equipped with a chain brake which is triggered automatically on impact and which stops

the saw chain immediately.

For safety reasons, the functionality of the chain brake must be checked each time before the device is used

(Checking the Chain Brake). W

ith less strong kickbacks, it can happen that the chain brake is not triggered

automatically. For this reason, it is important that the device should be held securely with both hands.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Chainsaw Kits - SW3 and SW4

Only a careful and correct working method can reduce the risk of a kickback reliably!

Basic Techniques

DANGER! Risk of injury! This section shows basic work techniques when handling the device.

The information provided here does not replace the many years of training and experience of a

professional. Do not perform any work for which you are not sufficiently qualified! Thoughtless handling of the

device can cause severe or even fatal injuries!

Before Each Use

1. Check the chain brake to ensure it is functioning correctly.

2. Check the rear hand guard for damage.

3. Check the switch-on safety lock and start button to ensure they are functioning correctly.

4. Check whether all handles are free of oil residues.

5. Check whether all parts of the device are present, firmly attached, and undamaged.

6. Check the chain catcher for damage.

7. Check the chain tensioning.

Pulling Sawing

With this technique, sawing occurs by starting on the underside of the saw rail and moving downwards. The saw

chain thus pushes the device forwards away from the user. This way, the front edge of the device forms a

support, which catches the forces that arise on the tree trunk when sawing.

With pulling sawing, the user has much more control over the device and can avoid kickbacks better. This is the

preferred sawing technique.

•

Saw as close to the motor block as possible. This prevents the saw from kicking back out of control.

•

If the bar saw is caught, pull the handle of the saw upwards. The leveraging effect will push the saw rail

down, making the sawing work easier.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Chainsaw Kits - SW3 and SW4

Pushing Sawing

With this technique, sawing occurs with the upper edge of the saw rail from below and slowly moving upwards.

The saw chain pushes the device backwards towards the user. If the saw rail twists, the device can fly towards

the user with great force.

The leveraging effect will push the saw rail down making, the sawing work easier.

If the user does not balance out the force of the saw chain pushing backwards with his or her bodily force, there

is a danger that only the tip of the saw rail will make contact with the wood and there will be a kickback!

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Chainsaw Kits - SW3 and SW4

Cutting Down Trees

DANGER! Risk of injury! Felling and delimbing work should only be performed by trained

people! There is a risk of fatal injuries! IMPORTANT! Small electric chainsaws are not suitable for

cutting down large trees, however the following information should be taken into consideration when cutting

down trees.

Before felling a tree, make sure that:

•

There are no people or animals in the felling area of the tree.

•

There is an obstacle-free escape route for each participant. A retreat

occurs diagonally counter to the felling direction.

•

The area around the trunk is free of obstacles (risk of stumbling!).

•

The next workplace is at least two and a half tree lengths away. Before

felling, the felling direction of the tree must be checked, and it must be

ensured that there are no objects, people, or animals within 2 ½ tree

lengths.

Tree felling occurs in two steps:

1. Notch the trunk by approximately one-third of its diameter on the felling direction side.

2. On the other side, make the felling cut, which must be somewhat higher than the felling notch (approx. 5

cm).

DANGER! Risk of injury! Never saw the tree trunk completely through. The area serves as a

"hinge" and ensures a defined felling direction. When felling, stand only to the side of the tree to

be felled! There is a risk of fatal injuries!

Trunks Lying Flat on the Ground

Cut into the trunk halfway, then turn over and saw through from the opposite side.

NOTICE! Device damage! Make sure that the saw rail does not touch the ground while you are sawing

through the trunk!

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Chainsaw Kits - SW3 and SW4

Propped-Up Trunks

We recommend that you place trunks to be sawed through on sawhorses. If this is not possible, the trunk should

be lifted with the help of supporting branches and placed over trestles.

In area A, first cut through approximately one-third of the trunk diameter from above and move slowly

downwards, then make the final cut from below, moving slowly upwards.

In area B, first cut through approximately one-third of the trunk diameter from below and slowly move upwards,

then saw through from above.

DANGER! Risk of injury! Do not saw any trunks under tension! Splintering wood or a twisted

saw rail can cause extremely severe injuries! Always place on the higher side of the trunk, as

there is a risk that it may roll away.

Removing Branches

•

Always work on the side opposite the branches.

•

Begin at the bottom of the trunk and work your way upwards.

•

Always guide the saw from above and slowly move downwards through the wood.

When removing branches from trunks which are lying down, first saw off the free branches sticking up in the air.

Only saw off supporting branches when the trunk is sawed in lengths.

DANGER! Risk of injury! Branches that are high up or under tension can wedge the saw chain

in the wood!

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Chainsaw Kits - SW3 and SW4

Lithium Battery Care and Maintenance

Top 3 Battery Care Requirements

1. Charge battery before first use. The battery may arrive with some charge, regardless of this the

battery must be charged for 2 hours on the initial charge and 2 hours for each subsequent charge.

2. Charge battery immediately when it is depleted. Do not store a depleted battery. This will

permanently impact the life of the battery. If the battery is going to be stored for a period of time, fully

charge the battery before storing.

3. Disconnect battery when not in use. To prolong the life of a battery, disconnect it from the unit

when not in use. Disconnect chargers from the battery once charged.

To ensure the battery maintains optimum performance, follow the guidelines outlined below.

•

For best results, charge batteries in temperatures between 10°C and 30°C

•

When battery is charged, disconnect the charger from the power supply and remove the battery from the

charger.

•

If a battery is stored or otherwise unused for an extended period, and the battery has no charge remaining

when you check it, consider it to be damaged. Do not attempt to recharge it or to use it. Replace it with a

new battery.

•

Use only with the battery charger specified by the manufacturer.

•

Ensure that the battery charger electrical cord is not subjected to damage or stress. Do not operate the

battery charger if it has a damaged electrical cord or plug.

•

Do not use the charger in wet areas or expose it to rain or water.

•

The typical estimated life of a Lithium-Ion battery is about two to three years or 300 to 500 charge cycles,

whichever occurs first. One charge cycle is a period of use from fully charged, to fully discharged, and fully

recharged again

•

Explosion hazard – protect the battery against heat; for example, direct sunlight and fire. Do not store

batteries in vehicles or locations subject to heat.

•

Batteries can explode in the presence of an ignition source, such as a pilot light. To reduce the risk of

serious personal injury, never use any cordless product in the presence of open ﬂame. Exploding batteries

can propel debris and chemicals.

•

Do not open the battery – danger of short-circuiting and/or explosion.

•

Do not attempt to destroy or disassemble the battery pack or remove any of its components.

•

Do not touch the battery terminals with metal objects and/or body parts as short-circuit and/or personal injury

may result.

•

Explosion hazard – do not open and/or short-circuit the battery.

•

Poison hazard – battery leakage (liquid ejection). Under extreme conditions, liquid may be ejected from the

battery – avoid contact. If contact accidentally occurs, immediately seek medical attention, and flush with

water. If liquid contacts eyes, immediately seek medical attention, flush with clean water for at least 10

minutes. Liquid ejected from the battery may cause irritation or burns.

•

Dispose of non-serviceable batteries in an environmentally responsible manner and according to local

regulations.

Failure to adhere to the requirements above may result in the battery becoming inoperative or battery life being

reduced. In extreme cases or abuse, battery overheating or fire may result.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Chainsaw Kits - SW3 and SW4

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Chainsaw Kits - SW3 and SW4

Maintenance

DANGER! Risk of injury! Before any maintenance or cleaning work: Remove the battery. Let the

device cool down.

Cleaning the Device

1. Remove any coarse dirt.

2. Wipe down the device with a slightly damp cloth.

Cleaning the Oil Guide Groove of the Saw Rail

1. Remove the saw rail.

2. Remove any dirt from the oil guide groove of the saw rail with a suitable tool like a plastic spatula. Do not

use any steel tools!

3. Replace the saw rail (Assembling the Saw Rail and Saw Chain

).

Re-Tensioning the Saw Chain

1. Lift the tip of the saw rail slightly.

2. Tighten the tensioning screw (6) until the chain lies on the underside of the saw rail.

Sharpening the Saw Chain

Special tools are required to sharpen the saw chain; these guarantee that the cutting of the chain occurs at the

correct angle and the correct depth. We recommend that you have the saw chain sharpened by a professional.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Chainsaw Kits - SW3 and SW4

Storage and Transportation

Storage

DANGER! Risk of injury! Make sure that unauthorised persons do not have access to the

device!

•

Let the device cool down before you store it.

•

Store the device horizontally, if possible.

Longer downtimes:

If you are not going to be using the device for a while, remove the chain oil from the device. Store the device in a

dry place.

Transportation

If you are transporting the device in a vehicle:

•

Slip the protective cover onto the cutting tool.

•

Secure the device against slippages.

•

If possible, use the original packaging for transporting.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Chainsaw Kits - SW3 and SW4

Troubleshooting

DANGER! Risk of injury! Unprofessional repairs may mean that your unit will no longer operate

safely. This endangers you and your environment.

Malfunctions are often caused by minor faults. You can easily remedy most of these yourself. Please consult the

following table before contacting a qualified technician or an authorised service centre.

Error/Fault Cause Remedy

Unit does not work.

Battery not inserted correctly.

Adjust and ensure the battery is

inserted correctly.

Battery pack discharged. Charge the battery pack.

Battery pack defective.

Contact a qualified technician or an

authorised service centre.

Unit is defective.

Contact a qualified technician or an

authorised service centre.

NOTE: If you cannot fix the fault yourself, contact a qualified technician or an authorised service centre. Please

be aware that any improper repairs will also invalidate the warranty and additional costs may be incurred.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Chainsaw Kits - SW3 and SW4

Specifications

SW3

Type of chainsaw

Top Handle Chainsaw/Arborist Chainsaw

Cutting capacity

10”

Power Source

Battery/Cordless

Power

250-300W

Battery

Lithium-Ion, 20v 2.0 ah Battery- 18650 cells

Continuous run time if fully charged

(mins.)

Machine can run about 18mins without chain, 6-7mins with chain

without cutting

Battery life cycle (times)

More than 300 cycles of normal charge and discharge

Power plug

240V SAA

Bar

10” Oregon

Chain specs-type

3 / 8 inch

Chain specs-brand

Oregon

Chain specs-drive links

40

Chain specs-gauge

0.053

Chain specs-pitch

3 / 8 inch

Cutting Speed

5m/s

Adjustable speed

Yes

Oil Tank Capacity

≥ 120mL

Bar and Chain Lubrication

Automatic

Toolless Chain Tensioning and Chain

Change

Yes

Ergonomic Operation and a Secure Hold

Yes

Automatic Chain Oiling

Yes

Kickback Protection with Instant Chain

Brake

Yes

Electronic Brake + Mechanical Brake

Yes

Front hand guard for safe operation

Yes

Auto-oil-lubrication

Yes, oil output rate 2-6ml/min

Oil level window

Yes

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Chainsaw Kits - SW3 and SW4

SW4

Type of chainsaw

Top Handle Chainsaw/Arborist Chainsaw

Cutting capacity

12"

Power Source

Battery/Cordless

Power

250-300W

Battery

Lithium-Ion, 20v 2.0 ah Battery- 18650 cells

Continuous run time if fully charged

(mins.)

Machine can run about 18mins without chain, 6-7mins with chain

without cutting

Battery life cycle (times)

More than 300 cycles of normal charge and discharge

Power plug

240V SAA

Bar

12” Oregon

Chain specs-type

3 / 8 inch

Chain specs-brand

Oregon

Chain specs-drive links

45

Chain specs-gauge

0.053

Chain specs-pitch

3 / 8 inch

Cutting Speed

5m/s

Adjustable speed

yes

Oil Tank Capacity

≥ 120mL

Bar and Chain Lubrication

automatic

Toolless Chain Tensioning and Chain

Change

Yes

Ergonomic Operation and a Secure

Hold

Yes

Automatic Chain Oiling

Yes

Kickback Protection with Instant Chain

Brake

Yes

Electronic Brake + Mechanical Brake

Yes, pull this bar to activate the brake

Front hand guard for safe operation

Yes

Auto-oil-lubrication

Yes, oil output rate 2-6ml/min

Oil level window

Yes

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Some experts believe that the incorrect or prolonged use of almost any

product may cause serious injury or death. To help reduce your risk of

serious injury or death, refer to the information below. For more information,

see www.datastreamserver.com/safety



Consult all documentation, packaging

and product labelling before use. Note

that some products feature

documentation available online. It is

recommended to print and retain the

documentation.



Before each use, check the product for

loose/broken/damaged/missing parts,

wear or leaks (if applicable). Never use a

product with

loose/broken/damaged/missing parts,

wear or leaks.



Products must be inspected and serviced

(if applicable) by a qualified technician

every 6 months. This is based on

average residential use by persons of

average size and strength, and on a

property of average metropolitan size.

Use beyond these recommendations may

require more frequent

inspections/servicing.



Ensure that all users of the product have

completed a suitable industry recognised

training course before being allowed

access to the product.



The product has been supplied by a general merchandise

retailer that may not be familiar with your specific

application or description of application. Be sure to attain

third-party approval from a qualified specialist for your

application before use, regardless of any assurances from

the retailer or its representatives.



This product is not intended for use where fail-safe

operation is required. As with any product (for example,

automobile, computer, toaster), there is the possibility of

technical issues that may require the repair or

replacement of parts, or the product itself. If the possibility

of such failure and the associated time it may take to

rectify could in any way inconvenience the user, business

or employee, or financially affect the user, business or

employee, then the product is not suitable for your

requirements. This product is not intended for use where

incorrect operation or a failure of any kind, including but

not limited to, a condition requiring product return,

replacement, parts replacement or service by a technician

may cause financial loss, loss of employee time or an

inconvenience requiring compensation.



If this product has been purchased in error when

considering the information presented here, contact the

retailer directly for details of their returns policy, if

required.

ideas, diagrams or images may be reproduced or transmitted in any form or by any means, electronic or

mechanical, including photocopying, scanning or recording, or any information storage and retrieval system,

without express permission or consent from the publisher.

Oregon CHNSAWBMRASW3 Baumr-AG 20V 10" Bar Cordless Chainsaw Lithium-Ion Electric Pruner Garden

Product's Documents

Product manual

Specifications

Oregon CHNSAWBMRASW3 Questions and Answers