REFER TO INSTRUCTIONS
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE
AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
FLEXI GRIP NITRILE PALM GLOVES
(X-LARGE) - PACK OF 6 PAIRS
MODEL NO: TSP125L & TSP125XL/6
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
1. INTRODUCTION
Nitrile coated palm gives superior grip and dexterity. Good abrasion resistance. Breathable open back. CE Marked and conforms to BS
EN 388:2016 4-1-2-2-X.
Sizes: TSP125L/6 (Large), TSP125XL/6 (Extra-Large)
Notied Body: 0075
Type Examination Certicate Number: 0075/1022/162/11/18/2709
Carried Out By: CTC
2. SAFETY
9 Users should be warned that gloves should not be worn when there is a risk of entanglement by moving parts of machines.
9 This model does not contain any substances at levels that are known to, or suspected to, adversely aect user hygiene or health.
9 The protection against risks or hazards which are not mentioned in this document is not warranted.
9 The levels of performance mentioned are only valid for the palm of the glove.
9 These levels of performance are obtained from the tests done according to the conditions dened by the applicable standards.
9 This glove shall not be in contact with re.
9 Before use, the glove shall be visually controlled. In case of deterioration the gloves must be scrapped (abrasion, cut, tear, ...).
9 For gloves with two or more layers of material, the performance levels are warranted only for the whole glove.
9 For gloves with two or more layers the overall classication does not necessarily reect the performance of the outermost layer.
3. APPLICABLE STANDARDS
Mechanical Hazard
EN 388 : 2016
4122X
Abrasion Resistance 4 (on 4 maxi) ‘X’ indicates that the glove has
not been submitted to the test or
the test method appears not to
be suitable for the glove design
or material.
Blade Cut Resistance 1 (on 5 maxi)
Tear Resistance 2 (on 4 maxi)
Puncture Resistance 2 (on 4 maxi)
Cut Resistance Method (EN ISO 13997) X (A to F)
Impact Protection -
4. MAINTENANCE
4.1. STORAGE
9 Store the gloves in their original packaging.
9 Store the gloves in normal temperature and humidity conditions.
9 Store the gloves in clean, covered and ventilated premises.
4.2. MAINTENANCE
9 The gloves should be inspected before each use, and replaced if damaged.
TSP125L & TSP125XL/6 Issue 1 06/10/23
Original Language Version
© Jack Sealey Limited
EU | Sealey EU Ltd, Farney Street, Carrickmacross, Co. Monaghan, A81 PK68 Ireland
UK | Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 sales@sealey.co.uk www.sealey.co.uk
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted,
taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product
becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and
dispose of the product and fluids according to local regulations.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
REGISTER YOUR
PURCHASE HERE
This document has been drawn up according to Regulation (EU) 2016/425 as amended to apply to GB for Personal Protective
Equipment. The declaration of conformity can be accessed at www.sealey.co.uk.
